Related Manuals for Bosch DIP-7384-8HD
Summary of Contents for Bosch DIP-7384-8HD
- Page 1 DIVAR IP all‑in‑one 7000 2U DIP‑7380‑00N | DIP‑7384‑8HD | DIP‑7388‑8HD | DIP‑738C‑8HD Installation manual...
-
Page 3: Table Of Contents
Installing a SSD hard drive into a rear drive bay 10.5.1 Removing a hard drive carrier from a rear hard drive bay 10.5.2 Installing a hard drive into a rear hard drive carrier Bosch Security Systems B.V. 2020.11 | V1.1 | DOC Installation manual... - Page 4 Replacing a system fan 10.11 Replacing the power supply 10.12 Replacing the power distributor 10.13 Service and repair Additional information 11.1 Additional documentation and client software 11.2 Support services and Bosch Academy 2020.11 | V1.1 | DOC Bosch Security Systems B.V. Installation manual...
-
Page 5: Safety
The Low Voltage power supply unit must comply with EN/UL 60950. The power supply must be a SELV-LPS unit or a SELV - Class 2 unit (Safety Extra Low Voltage - Limited Power Source). Bosch Security Systems B.V. 2020.11 | V1.1 | DOC Installation manual... - Page 6 Clean only with a dry cloth. Do not use liquid cleaners or aerosol cleaners. – Do not install device near any heat sources such as radiators, heaters, stoves, or other equipment (including amplifiers) that produce heat. 2020.11 | V1.1 | DOC Bosch Security Systems B.V. Installation manual...
- Page 7 16 A. This must be in accordance with NEC800 (CEC Section 60). – Disconnect the power before moving the unit. Move the unit with care. Excessive force or shock may damage the unit and the hard disk drives. Bosch Security Systems B.V. 2020.11 | V1.1 | DOC Installation manual...
-
Page 8: Electrical Safety Precautions
SELV circuits. – If safe operation of the unit cannot be ensured, remove it from service and secure it to prevent unauthorized operation. In such cases, have the unit checked by Bosch Security Systems. –... -
Page 9: Esd Precautions
Notice! Video loss is inherent to digital video recording; therefore, Bosch Security Systems cannot be held liable for any damage that results from missing video information. To minimize the risk of losing information, we recommend multiple, redundant recording systems, and a procedure to back up all analog and digital information. -
Page 10: Fcc And Ices Compliance
| Safety DIVAR IP all-in-one 7000 2U Disposal Your Bosch product has been developed and manufactured using high-quality materials and components that can be reused. This symbol means that electronic and electrical devices that have reached the end of their working life must be disposed of separately from household waste. - Page 11 OS security updates. – Limiting local network access to trusted devices is strongly suggested. Details are described in the Technical note Network Authentication 802.1X and in the Bosch IP Video and Data Security Guidebook, available in the online product catalog. –...
-
Page 12: About This Manual
This manual is written for professional system integrators and PC technicians. It provides information for the installation and use of the chassis. Installation and maintenance should be performed by experienced and qualified technicians only. 2020.11 | V1.1 | DOC Bosch Security Systems B.V. Installation manual... -
Page 13: System Overview
The chassis includes a control panel on the front that features power buttons and status monitoring LEDs. On the rear there are various I/O ports as well as power supply modules. Bosch Security Systems B.V. 2020.11 | V1.1 | DOC... - Page 14 USB port 3.1 Gen 2 (Type C) 2 LAN ports (teamed) Note: Do not change the teaming mode! VGA display output (disabled) DVI-I port 2 DisplayPort ports Audio Line out Audio MIC in 2020.11 | V1.1 | DOC Bosch Security Systems B.V. Installation manual...
-
Page 15: Control Panel Elements
This LED indicates network activity on GLAN2 when flashing. NIC2 This LED indicates network activity on GLAN1 when flashing. NIC1 Bosch Security Systems B.V. 2020.11 | V1.1 | DOC Installation manual... -
Page 16: Hard Drive Carrier Leds
The system power supply temperature has reached 63 °C. The system will automatically turn off when the power supply temperature reaches 70 °C and restart when the power supply temperature goes below 60 °C. 2020.11 | V1.1 | DOC Bosch Security Systems B.V. Installation manual... -
Page 17: Preparing For Installation
– Allow the hard drives and power supply modules to cool before touching them. Bosch Security Systems B.V. 2020.11 | V1.1 | DOC Installation manual... -
Page 18: Installation Considerations
A reliable ground must be maintained at all times. To ensure this, the rack itself should be grounded. Particular attention should be given to power supply connections other than the direct connections to the branch circuit (i.e. the use of power strips, etc.). 2020.11 | V1.1 | DOC Bosch Security Systems B.V. Installation manual... -
Page 19: Rack Installation
Locate the rail assembly in the chassis packaging. Extend the rail assembly by pulling it outward. Press the quick-release tab. Separate the inner rail extension from the outer rail assembly. Bosch Security Systems B.V. 2020.11 | V1.1 | DOC Installation manual... -
Page 20: Installing The Inner Rails On The Chassis
Hang the hooks of the rails onto the rack holes and if desired, use screws to secure the front of the outer rail onto the rack. Repeat steps 1-3 for the remaining outer rail. 2020.11 | V1.1 | DOC Bosch Security Systems B.V. Installation manual... -
Page 21: Installing The Chassis In The Rack
Push the chassis completely into the rack and make sure that it clicks into the locked position. Optionally, use screws to secure the front of the chassis to the rack. Bosch Security Systems B.V. 2020.11 | V1.1 | DOC Installation manual... - Page 22 Make sure that the brackets are positioned with just enough space to fit the width of the Telco rack. Slide the chassis into the rack and tighten the brackets to the rack. 2020.11 | V1.1 | DOC Bosch Security Systems B.V. Installation manual...
-
Page 23: Installing A Sata Hard Drive
Installing a hard drive into a hard drive carrier To install a hard drive into a hard drive carrier: Remove the screws which secure the dummy drive to the hard drive carrier. Bosch Security Systems B.V. 2020.11 | V1.1 | DOC Installation manual... - Page 24 SATA hard drive Notice! Bosch recommends using the respective Bosch hard disk drives. The hard disk drives as one of the critical component are carefully selected by Bosch based on available failure rates. Hard disk drives not delivered from Bosch are not supported.
-
Page 25: Installing A Hard Drive Carrier Into A Front Drive Bay
Push the hard drive carrier into the bay until the handle retracts and the hard drive clicks into the locked position. Bosch Security Systems B.V. 2020.11 | V1.1 | DOC Installation manual... -
Page 26: Turning On The System
Plug the power cord from the power supply unit into a high-quality power strip that offers protection from electrical noise and power surges. Bosch recommends to use an uninterruptible power supply (UPS). Push the power button on the control panel to turn on the system. -
Page 27: System Setup
– Pure video recording system, utilizing the VRM core components and services. – iSCSI storage expansion for a BVMS or VRM system, which runs on a different hardware. Bosch Security Systems B.V. 2020.11 | V1.1 | DOC Installation manual... -
Page 28: Preparing Hard Drives For Video Recording
Following procedure describes how to restore the factory default image. To restore the unit to factory default image: Start the unit and press F7 during the BIOS power-on-self-test. The Recovery menu is displayed. Select one of the following: 2020.11 | V1.1 | DOC Bosch Security Systems B.V. Installation manual... - Page 29 Windows performs the initial setup of the operating system. The unit restarts after Windows has completed the setup. After the restart of the unit, the factory settings are installed. Bosch Security Systems B.V. 2020.11 | V1.1 | DOC Installation manual...
-
Page 30: Troubleshooting
Make sure that the chassis covers are installed. – Make sure that the heat sinks are installed properly. – Make sure that the ambient room temperature is not too high. 2020.11 | V1.1 | DOC Bosch Security Systems B.V. Installation manual... -
Page 31: Maintenance
To remove the power: Shut down the system. Remove the power cords from the power supplies. Disconnect the cord from the power strip or wall outlet. 10.3 Removing the chassis cover Bosch Security Systems B.V. 2020.11 | V1.1 | DOC Installation manual... -
Page 32: Identifying A Faulty Ssd Drive
SATA port 2: refers to the SSD located in the right tray After you have identified the faulty SSD drive, open the corresponding tray on the back of the system and replace the SSD drive. 2020.11 | V1.1 | DOC Bosch Security Systems B.V. Installation manual... -
Page 33: Installing A Ssd Hard Drive Into A Rear Drive Bay
Note: To secure the hard drive, you cannot reuse the screws that are used to secure the dummy drive to the tray. Bosch Security Systems B.V. 2020.11 | V1.1 | DOC Installation manual... -
Page 34: Installing A Hard Drive Carrier Into A Rear Hard Drive Bay
DIVAR IP all-in-one 7000 2U Notice! Bosch recommends using the respective Bosch hard disk drives. The hard disk drives as one of the critical component are carefully selected by Bosch based on available failure rates. Hard disk drives not delivered from Bosch are not supported. -
Page 35: Replacing The Fron Port Panel
Insert the new front port panel unit in the slot until the tab locks into place. Connect the data and power cables to the backplane and motherboard. 10.8 Installing the motherboard Motherboard problems will be handled by trained support people only. Bosch Security Systems B.V. 2020.11 | V1.1 | DOC Installation manual... -
Page 36: Installing The Air Shroud
The fans might still be turning when you remove the fan assembly from the chassis. Keep fingers, screwdrivers, and other objects away from the openings in the fan assembly's housing. 2020.11 | V1.1 | DOC Bosch Security Systems B.V. Installation manual... -
Page 37: Replacing The Power Supply
This unit might have more than one power supply connection. To de-energize the unit, remove all connections. LED status: – Amber lighted LED: The power supply is off. – Green lighted LED: The power supply is operating. Bosch Security Systems B.V. 2020.11 | V1.1 | DOC Installation manual... -
Page 38: Replacing The Power Distributor
The power supply can be replaced without turning off the system if a redundant power supply is available. Replacement units can be ordered directly from Bosch RMA desk. To replace the power supply: Unplug the AC power cord of the failed power supply. -
Page 39: Service And Repair
The storage equipment is shipped with an original manufacturer Service and Support agreement. The Bosch Technical Support is the Single Point of Contact in case of failure but the Service and Support obligations are fulfilled by the manufacturer or a partner. -
Page 40: Additional Information
– Repair & Exchange – Product Security Bosch Building Technologies Academy Visit the Bosch Building Technologies Academy website and have access to training courses, video tutorials and documents: www.boschsecurity.com/xc/en/support/training/ 2020.11 | V1.1 | DOC Bosch Security Systems B.V. Installation manual... - Page 41 DIVAR IP all-in-one 7000 2U Additional information | Bosch Security Systems B.V. 2020.11 | V1.1 | DOC Installation manual...
- Page 42 | Additional information DIVAR IP all-in-one 7000 2U 2020.11 | V1.1 | DOC Bosch Security Systems B.V. Installation manual...
- Page 44 Bosch Security Systems B.V. Torenallee 49 5617 BA Eindhoven Netherlands www.boschsecurity.com © Bosch Security Systems B.V., 2020 202101051352...