Advertisement
Quick Links
EU Light Kit
Serial Number 400000000 and After Groundsmaster
Series Rotary Mower with Cab
Model No. 30653—Serial No. 400000000 and Up
Safety
Safety and Instructional Decals
Safety decals and instructions are easily visible to the operator and are located near any area of
potential danger. Replace any decal that is damaged or missing.
136-0007
1. Brakes
Installation
Loose Parts
Use the chart below to verify that all parts have been shipped.
Procedure
1
2
3
4
© 2022—The Toro® Company
8111 Lyndale Avenue South
Bloomington, MN 55420
Description
No parts required
No parts required
Flasher module
Wire harness
Switch
Auxiliary-brake decal
Right headlight mount
Left headlight mount
Cover panel
Plug
Right headlight assembly
Left headlight assembly
Register at www.Toro.com.
decal136-0007
Qty.
–
–
1
1
1
1
1
1
2
8
1
1
Form No. 3413-860 Rev B
®
5900 or 5910
Installation Instructions
Use
Prepare the machine.
Disconnect the battery.
Install the flasher module.
Install the headlights (for machines with
ROPS only).
*3413-860*
Original Instructions (EN)
Printed in the USA
All Rights Reserved
Advertisement
Related Manuals for Toro 30653
Summary of Contents for Toro 30653
- Page 1 Serial Number 400000000 and After Groundsmaster ® 5900 or 5910 Series Rotary Mower with Cab Model No. 30653—Serial No. 400000000 and Up Installation Instructions Safety Safety and Instructional Decals Safety decals and instructions are easily visible to the operator and are located near any area of potential danger.
- Page 2 Procedure Description Qty. Right headlight mount Left headlight mount Right headlight assembly Left headlight assembly Bolt (1/2 x 1-1/4 inches) Install the headlights (for machines with a cab only). Nut (1/2 inch) Bolt (1/4 x 3/4 inch) Nut (1/4 inch) Cable tie Front wire harness Plate light...
-
Page 3: Preparing The Machine
Preparing the Machine No Parts Required Procedure Park the machine on a level surface. Engage the parking brake. Shut off the engine and remove the key. g038719 Figure 1 Disconnecting the Battery No Parts Required Procedure Turn the battery-disconnect switch to the O position. - Page 4 Installing the Flasher Module Parts needed for this procedure: Flasher module g186717 Figure 4 Wire harness 1. Switch 3. Knockout Switch 2. Auxiliary-brake decal Auxiliary-brake decal Adhere the auxiliary-brake decal above the switch (Figure Procedure Connect the new wire harness to the flasher Remove the 6 bolts from the console and module, hazard switch, turn-signal switch, and remove the panel...
- Page 5 Installing the Headlights (for Machines with ROPS only) Parts needed for this procedure: Right headlight mount Left headlight mount Cover panel Plug Right headlight assembly Left headlight assembly g035974 Figure 7 Procedure 1. Headlight assembly 3. Previously removed fasteners Unplug the wire harness from each existing 2.
- Page 6 Route the wire harness through the bracket and under the operator platform (Figure Connect the wire harness to both connectors that you unplugged from the existing headlights and connect the front turn signal connector to the platform wire harness (Figure Route the wire harness through the left headlight bracket and connect it to the left headlight (Figure...
- Page 7 Route the wire harness along the bracket and under the operator platform (Figure 10). Connect the wire harness to both connectors that you unplugged from the existing headlights and connect the front turn signal connector to the platform wire harness (Figure 10).
- Page 8 Remove the tail lights from the machine (Figure Installing the Rear Lights Parts needed for this procedure: Right pivot bracket Left pivot bracket Pivot arm Left lamp shroud Right lamp shroud Cable tie g035978 Figure 13 Clip Rear lamp panel 1.
- Page 9 Hold the pivot bracket on the rear of the left Insert a roll pin in the pivot arm (Figure 17). frame and drill 3 holes (10 mm or 0.39 inch diameter) in the locations shown in Figure Note: You will not use the lower front hole in the pivot bracket.
- Page 10 Install the left light to the shroud using 2 bolts Route the wire harness under the frame of (M6 x 30) and 2 nuts (M6) that you removed in the machine and connect the other end of 2 (Figure 19). the tail-light wire harness to the machine wire harness.
- Page 11 edge (Figure 25). Use the serial plate as a template and drill 4 holes (3 mm or 1/8 inch). Installing the Signs and Serial Plate Parts needed for this procedure: Sign Serial plate Procedure Adhere a sign on both sides of the machine (Figure 24).
-
Page 12: Operation
Check the operation of the lights. Make sure that the correct lights are flashing when Verify that the machine is in CE mode. If it is operating the turn signal switch. not in CE mode; contact your authorized Toro distributor (Figure Aiming the Headlights Loosen the mounting nuts to adjust the lights. - Page 13 Using the Auxiliary-Brake Switch Press and hold the auxiliary-brake switch to decrease the engine speed (Figure 28); release the switch to stop the deceleration and remain at the current engine speed. Note: You may use the switch intermittently to gradually slow the machine. If you press the switch when the engine speed is below 1,200 rpm or if the engine decelerates to 1,200 rpm, the engine shuts off and the machine stops.
- Page 14 The Toro Company (“Toro”) respects your privacy. When you purchase our products, we may collect certain personal information about you, either directly from you or through your local Toro company or dealer. Toro uses this information to fulfil contractual obligations - such as to register your warranty, process your warranty claim or to contact you in the event of a product recall - and for legitimate business purposes - such as to gauge customer satisfaction, improve our products or provide you with product information which may be of interest.
- Page 15 Countries Other than the United States or Canada Customers who have purchased Toro products exported from the United States or Canada should contact their Toro Distributor (Dealer) to obtain guarantee policies for your country, province, or state. If for any reason you are dissatisfied with your Distributor's service or have difficulty obtaining guarantee information, contact your Authorized Toro Service Center.