JVC HR-S5966EK Instructions Manual
Hide thumbs
Also See for HR-S5966EK:
- Instructions manual (60 pages) ,
- Schematic diagrams (22 pages) ,
- Instructions manual (17 pages)
Related Manuals for JVC HR-S5966EK
Summary of Contents for JVC HR-S5966EK
- Page 1 VIDEO CASSETTE RECORDER HR-S5965EK HR-S5966EK HR-S5967EK – –:– – AUDIO VPS/PDC 0000 30 SEC ENTER S-VHS LP00000-000 VCR/TV IN STRU CTION S LPT0768-001B...
- Page 2 In the unlikely event of the plug fuse failing be sure to replace the fuse only with an identical approved type, as originally fitted, and to replace the fuse cover. If the fuse fails again consult your nearest JVC dealer. If nonetheless the mains plug is cut off remove the fuse and dispose of the plug immediately, to avoid a possible shock hazard by inadvertent connection to the mains supply.
- Page 3 safety first When the equipment is installed in a cabinet or a shelf, make sure that it has sufficient space on all sides to allow for ventilation (10 cm or more on both sides, on top and at the rear.) When discarding batteries, environmental problems must be considered and the local rules or laws governing the disposal of these batteries must be followed strictly.
- Page 4 safety first Some Do’s And Don’ts On The Safe Use Of Equipment This equipment has been designed and manufactured to meet international safety standards but, like any electrical equipment, care must be taken if you are to obtain the best results and safety is to be assured.
-
Page 5: Table Of Contents
Contents Diagrams of Equipment ........ 6 Equipment Key ..........7 Welcome to JVC ..........8 Three-Step Quick Start ....... 10 Basic Features ..........13 Advanced Features ........27 Subsidiary Information ......53 List of Terms ..........57... -
Page 6: Diagrams Of Equipment
diagrams of equipment S-VHS front panel & – –:– – AUDIO ENTREE ANT. IN SORTIE ENTREE/DECODEUR ENTREE/SORTIE ANTENNE IN/DECODER IN/OUT SORTIE RF OUT AUDIO VPS/PDC *DECODER function is not available in the UK. 0000 rear panel 30 SEC 7 6 5 S-VHS ENTER LP00000-000... -
Page 7: Equipment Key
31 TV +/– Buttons control recording (press . the same 6 c Indicator lights when cancels Pause, Still, Slow, volume of connected JVC TV. time). the c button has been Search modes. 32 D E Buttons initiate 12 S Button stops tape. -
Page 8: Welcome To Jvc
VPS/PDC 0000 RF Cable Depending on the type 30 SEC of JVC TV. Some or all functions cannot be operated using the Remote Control. If the Remote Control ENTER doesn’t work properly, remove it’s battery,... - Page 9 GETTING EVERYTHING READY (continued) connect cables Connect the cables as indicated in the diagram (below), using the TV Aerial Cable, the RF Cable and the 21-pin SCART Cable (not provided). RF Cable (provided) TV Aerial Cable (not...
-
Page 10: Three-Step Quick Start
– –:– – the Remote Control and try again. If you cannot obtain the vertical white bars on any channel between 22 and 69, consult your local JVC dealer. rf and scart connection If you have chosen S-VHS to connect the VCR to the TV with both the RF... - Page 11 TV picture while the VCR’s power is on. Set your Video Channel manually. ( pg. 44, Video Channel Set IF YOU HAVE ANY DIFFICULTY WITH THE ABOVE PROCEDURES CALL THE JVC CUSTOMER SERVICE HOT LINE ON 0870 330 5000...
- Page 12 three-step quick start...
-
Page 13: Basic Features
Basic Features Playback............. 14 Playback Features ........16 Recording ........... 18 VIDEO Plus+ ® Timer Programming .... 21 Express Timer Programming ...... 24... -
Page 14: Playback
basic features Playback Playback is the most basic operation possible with your VCR. Audio-visual information recorded on a cassette will be played back on your TV screen just like a broadcast programme. Load a Video Cassette before you start Make sure that the window side of the cassette is facing up and the spine label is facing away from the VCR. - Page 15 • flaw, dirt or mold on video tapes. • continuous usage for a long time. Use a dry cleaning cassette — JVC TCL-2 — in the following cases: • Rough, poor picture appears while a tape is played back. •...
-
Page 16: Playback Features
basic features Playback Features Pause During Playback Press the | button on the VCR or the Remote Control. • If the paused picture on the TV screen jumps vertically, press the button on the Remote Control until the picture is steady. •... - Page 17 basic features Slow Motion This VCR will play your cassette forwards or backwards in slow motion. You can make it do this in one of two ways: method one During still picture, press and hold | on the VCR or the Remote Control for 2 seconds, then release.
-
Page 18: Recording
basic features Recording TV signals being received by the recorder’s built in tuner can be recorded onto a video tape. You can ‘capture’ a TV programme using your VCR. Choose a Programme before you start Press or the number keys on the Remote Control to select the channel that you wish to record. - Page 19 basic features Notes on Recording When using both the RF and SCART connections, you can switch between TV – –:– – and VCR by pressing the button on the Remote Control. TV/VCR If the tape reaches its end during recording, the recording stops and “U” and “,”...
- Page 20 basic features Recording Resume Function If there is a power cut during recording (or Instant Timer Recording or timer recording), the recording will resume automatically when power is restored to the VCR unless the VCR’s memory backup has expired. Instant Timer Recording This method allows you to quickly set the VCR to record in 30 minute incre- ments.
-
Page 21: Video Plus + Timer Programming
basic features ® VIDEO Plus + Timer Programming before you start The VIDEO Plus+ system uses the code numbers – called PlusCode numbers – printed after each programme in your TV listings guide. These are a kind of Make sure that the shorthand for video recorders and using them automatically sets your VCR VCR’s clock is set to record the correct programme, channel and time. - Page 22 basic features Check the Results Press . The VIDEO Plus+ Program screen VPS/PDC appears. -P2- PLUSCODE NO. 56781234 START STOP -P1- Make sure that the preset number displayed is the 21:00 22:00 VPS/PDC OFF one that you want. If it is incorrect, the wrong DATE TV PROG 25.12...
- Page 23 basic features Engage Timer Mode You must now put the VCR into Timer Mode by pressing c otherwise no recording will take place. c will appear on the display panel. Make sure that the VCR turns off automatically. To disengage the Timer Mode, press c again. If a video tape with the safety tab removed is loaded, c, Play indicator (,) and Record indicator (U) will flash.
-
Page 24: Express Timer Programming
basic features Express Timer Programming If you do not know the PlusCode number for the programme that you wish to record, follow the instructions below to manually set your VCR to record. before you start Get to the Timer Programming Set Screen Make sure that the VCR’s clock is set correctly... - Page 25 basic features set pdc mode Press PDC (number key 7 ) to change between ON and OFF . Programme Delivery Control ( ) is a service designed to ensure that timer recording still works in the event of a change in time of broadcast. If you set , your VCR will be turned on not by its own timer but by a signal transmitted by the broadcaster.
- Page 26 basic features Check, Cancel & Change Programmes Press c, then press o to disengage the timer START STOP DATE mode. 8:00 10:00 24.12 10:45 25.12 10:00 11:30 13:00 25.12 review the programmes Press C. The TV screen will display a list of the programmes set for timer recording (screen A).
-
Page 27: Advanced Features
Advanced Features Picture Quality .......... 28 Recording According To Tape Type....30 The B.E.S.T. Picture System ...... 32 Sound Modes ..........33 Finding Specific Scenes ......34 Auto Satellite Program Recording ..... 35 Editing ............37 Other Functions ......... 41 Connection to a Stereo System .... -
Page 28: Picture Quality
advanced features Picture Quality Manual Tracking Your VCR is equipped with automatic tracking control. This will be adequate for most tapes and will automatically adjust the tracking to suit the particular tape in use but if you insert an old or worn tape, it may be necessary to manually adjust the track- ing in order to get the best picture. - Page 29 advanced features Picture Control This feature allows you to select the most appropriate picture quality according to the type of tape or use of this VCR. The default setting is AUTO get to the mode set screen Press . Move the highlight bar to MODE SET using the (or E).
-
Page 30: Recording According To Tape Type
advanced features Recording According To Tape Type Super VHS ET (S-VHS ET) This function allows you to record in SP mode on VHS tapes with S-VHS picture quality. Tapes recorded using this function can be played back on a VCR equipped with the S-VHS ET func- tion. - Page 31 advanced features Super VHS (S-VHS), S-VHS ET and VHS Your VCR can record in S-VHS, S-VHS ET or VHS. To record in S-VHS: Perform the steps below to set . Then, insert a cassette marked ‘S-VHS’, the S-VHS S-VHS indicator will light on the display panel. The S-VHS recording mode will be selected. To record in S-VHS ET on a VHS cassette: See ‘Super VHS ET (S-VHS ET)’...
-
Page 32: The B.e.s.t. Picture System
advanced features The B.E.S.T. Picture System The Biconditional Equalised Signal Tracking (B.E.S.T.) System checks the about b.e.s.t. condition of the tape in use and compensates during recording and playback to give the best picture quality possible. The default setting is ON. Works in SP and LP modes Turning B.E.S.T. -
Page 33: Sound Modes
advanced features Sound Modes NICAM Stereo and Bilingual Broadcasts before you start This VCR is equipped with a digital stereo sound decoder ( NICAM ) which makes the reception of stereo and bilingual broadcasts possible. When the VCR is tuned Set On Screen Display to a different preset, the type of broadcast will be displayed on the TV screen for (O.S.D.) to ON... -
Page 34: Finding Specific Scenes
advanced features Finding Specific Scenes Skip Search During playback, press 3 up to 4 times. Each press of the 3 button will cause the VCR to go into fast-motion playback for a period of 30 seconds. Normal playback resumes automatically. •... -
Page 35: Auto Satellite Program Recording
advanced features Auto Satellite Programme Recording Auto Record from Satellite Receiver This facility allows a programme timer-recorded using the satellite receiver to be recorded on the VCR. connect up Connect your satellite receiver, TV and VCR (see diagram below). 21-pin AV Input Connectors Aerial Outdoor Unit... - Page 36 advanced features programme satellite receiver Enter the details of the programme into your satellite receiver (see receiver manual) and put a tape in the VCR. set tape speed Press / on the Remote Control to set the tape speed to either SP or LP . engage vcr in auto mode Press and hold SAT c (|)on the VCR for about 2 seconds.
-
Page 37: Editing
advanced features Editing L-1 OUTPUT Setting connector delivers either a composite signal (regular video L-1 IN/OUT signal) or a Y/C signal (a signal in which the luminance and chrominance signals are separated). Set to the appropriate mode depending on the type of L-1 OUTPUT unit connected to the rear panel L-1 IN/OUT... - Page 38 advanced features L-2 INPUT Setting L-2 IN/DECODER connector accepts either a composite signal (regular video signal) or a Y/C signal (a signal in which the luminance and chrominance signals are separated). Set L-2 INPUT to the appropriate mode depending on the output signals of the connected unit.
- Page 39 advanced features Editing Using Another VCR connect up Connect the player’s 21-pin SCART connector to the recorder’s 21-pin SCART connector as illustrated. When using your VCR as the player ..connect its L-1 IN/OUT connector to another VCR. When using your VCR as the recorder ..
- Page 40 advanced features Your VCR as the Player TV Set Your VCR ENTREE ANT. IN SORTIE ENTREE/DECODEUR ENTREE/SORTIE ANTENNE IN/DECODER IN/OUT SORTIE RF OUT AUDIO Video Channel 21-pin SCART Cables or AV Mode (not provided) RF Cable (provided) Another VCR ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ Your VCR as the Recorder Your VCR TV Set...
-
Page 41: Other Functions
advanced features Other Functions On-Screen Display (O.S.D.) This function allows you to turn the on-screen information get to the mode set screen Press , move the highlight M ODE SET bar to using the buttons and press MODE SET S-VHS ET B.E.S.T. - Page 42 advanced features Power Save Mode You can reduce the power consumption while the VCR is turned off. get to the mode set screen Press . Move the highlight M ODE SET bar to using the buttons and press MODE SET S-VHS ET B.E.S.T.
- Page 43 advanced features Auto Timer When the AUTO TIMER is set to , the timer is automatically engaged when the VCR power is turned off and automatically disengaged when the VCR is powered back on. get to the mode set screen Press .
-
Page 44: Connection To A Stereo System
advanced features Connection to a Stereo System It is possible to connect your VCR to a suitably equipped stereo system and listen to the soundtrack through the stereo system. connect up Connect the AUDIO OUT L and R connecters on the VCR to the AUX IN or TAPE MONITOR connecters on your stereo. -
Page 45: Video Channel Set
TV screen. If the bars do not appear or are not clear, choose another vacant channel and try again. If you cannot obtain the vertical white bars on any channel between 52 and 69, consult your local JVC dealer. Exit Video Channel Set Mode Press To view pictures from your VCR you must now set your TV to either the Video Channel or to AV mode, depending upon your choice above. -
Page 46: Tuner Set
advanced features Tuner Set The VCR needs to find, identify and memorise all available stations in your area in order to record programmes correctly. Once done, pressing the buttons enables you to jump to the available channels without going via any vacant channels. This channel search can be done either automatically or manually. - Page 47 advanced features Manual Channel Setup get to the confirmation screen Press . Move the high- MAIN MENU light bar to using the buttons and MANUAL CH SET (or E). MODE SET press AUTO CH SET MANUAL CH SET INITIAL SET [1] a k [MENU]: EXIT select position Use the...
- Page 48 advanced features Change Station Name get to the confirmation screen Press . Move the highlight bar to MANUAL CH SET (or E). using the buttons and press select position Use the button on the Remote Control to move the highlight bar to the preset position you want then press twice.
- Page 49 advanced features Change Station Preset Position get to the confirmation screen Press . Move the highlight bar to MANUAL CH SET (or E). using the buttons and press select item Use the button on the Remote Control until the item you want to move begins blinking then press .
- Page 50 advanced features Fine-Tuning Stored Channels get to the confirmation screen Press . Move the highlight bar to using MANUAL CH SET (or E). buttons and press select item Use the button on the Remote Control to move the highlight bar to the channel that you wish to fine-tune then press twice.
- Page 51 advanced features TV Station Channel Number Guide Region Transmitter BBC1 BBC2 London & South-East Bluebell Hill — Crystal Palace Dover — Heathfield — Oxford South-West Beacon Hill — Caradon Hill — Huntshaw Cross Redruth Stockland Hill — Channel Islands Fremont Point —...
-
Page 52: Clock Set
advanced features Clock Set You should only need to perform this function if: • Auto Clock Set was not performed correctly by Auto Setup, Preset Download or Auto Channel • The VCR’s memory backup has expired • You want to change the Just Clock setting Setting the Clock get to the initial set screen Press . -
Page 53: Subsidiary Information
subsidiary information Question and Answers PLAYBACK RECORDING What happens if the end of the tape is When I pause and then resume a reached during playback or search? recording, the end of the recording before The tape is automatically rewound to the the pause is overlapped by the beginning of beginning. - Page 54 • The video heads may be dirty. 4. The playback picture is blurred Use a dry cleaning cassette JVC or interrupted while TV broad- TCL-2 or consult your JVC dealer. casts are clear or USE CLEAN- ING CASSETTE message appears on the screen.
- Page 55 subsidiary information SYMPTOM POSSIBLE CAUSE CORRECTIVE ACTION RECORDING 1. Recording cannot be started. • There is no cassette loaded, or Insert a cassette, or using the cassette loaded has had its adhesive tape, cover the hole where the tab was removed. record safety tab removed.
- Page 56 subsidiary information SYMPTOM POSSIBLE CAUSE CORRECTIVE ACTION TIMER RECORDING (cont.) • The loaded cassette has had its Remove the cassette and cover 7. U, , and the SAT c indicator record safety tab removed. the hole with adhesive tape, or won’t stop blinking.
-
Page 57: List Of Terms
list of terms List of Terms A A A A A N N N N N Auto Channel Setup ..........46 Next Function Memory ........... 43 Auto Satellite Program Recording ......35 NICAM Stereo and Bilingual Broadcasts ....33 Auto Power ............... 43 NTSC Tapes .............. - Page 58 subsidiary information MEMO...
- Page 59 subsidiary information MEMO...
- Page 60 s p e c i f i c a t i o n s g e n e r a l Power requirement : AC 220 V – 240 V , 50 Hz/60 Hz Ó Power consumption : on : 16 W, off : 3.5 W Operating Temperature : 5°C to 40°C Storage Temperature: –20°C to 60°C Operating position : Horizontal only...
- Page 61 This file has been downloaded from: www.UsersManualGuide.com User Manual and User Guide for many equipments like mobile phones, photo cameras, monther board, monitors, software, tv, dvd, and othes.. Manual users, user manuals, user guide manual, owners manual, instruction manual, manual owner, manual owner's, manual guide, manual operation, operating manual, user's manual, operating instructions, manual operators, manual operator, manual product, documentation manual, user maintenance, brochure, user reference, pdf manual Downloaded from:...