Page 1
Model N o . : YC-500WX ● Thank you for your purchase of Panasonic welding power source. ● Before operating this product, please read the instructions carefully and save this manual for future use.First of all, please read “Safety precautions” or “Safety manual”.
Page 2
NOTICE: MACHINE EXPORT TO EUROPE This product does not meet the requirements specified in the EC Directives which are the EU safety ordinance. Please bear in mind that this product may not be brought as is into the EU. The same restriction also applies to any country which has signed the EEA accord.
Page 3
CONTENTS S a f e t y - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - Ⅰ I m p o r t a n t S a f e t y I t e m s - - - - - - - - - - - - - - - - - - - - - - - - - - - - Ⅱ...
Page 4
Disclaimer: ◆ Panasonic Welding Systems (Tangshan) Co., Ltd., (hereinafter called “PWST”) and its affiliates (including any subcontractor, sales company or agent) shall not assume or undertake any responsibility or liability of the followings: •Any problem arising out of, or directly or indirectly attributable to,the failure of user to carry out those normal maintenance, normal adjustment and periodical check of this product.
Safety precautions welding power source (10)Perform periodic checks without fail and repair or replace any damaged parts before using the power Observe the following instructions to source. prevent the hazard. Ventilation and protective equipment (1)Never use the welding power source for other than Oxygen deficit, fume and gas generated welding purpose.
Page 6
performing maintenance work or repair work, provide Installing shielding (curtain etc.) fence or the like around the welding machine so that unauthorized person can not come close carelessly. Arc flash, flying spatter, slugs, and noise generated during welding can Welding wire damage your eyes, skin and hearing.
Page 7
Notice: order better performance provide proper maintenance, please follow the below instructions: 1 If welding machine is placed on a slope, a countermeasure should be taken to keep it from falling on one side. 2 The degree of protection is IP21S, appropriate coverage is required in case of rain. 3 When using forklift, please fork welding machine at the side with “Fork”...
Page 9
Type YC-300WY Item Rated input voltage Three phase Phase Input voltage fluctuation tolerance Rated input voltage ±10% Rated frequency 50/60 (in common.) Rated input 10.5 No load voltage DC STICK voltage reducing "ON" : 14 voltage reducig "OFF" : 63 D.C.
Page 11
PREPARATION (1) Capacity of power supply facility and connecting cable Item Model YC-300/500WY4/500WX4 Supply voltage Phases Three-phase Faci1ity 40 or more Primary 1ine current approx.36.5 Input cable 14 or more Output cable 60 or more N.B. • Turn off the switch of the switch box when connection cable. •...
Page 29
[Precations for flow switch] Water pressure: This machine uses a flow rate switch to prevent the water-cooled torch from burning. For the flow rate switch, since the water amount becomes small in a low water pressure place, "WARN." indicator lamp lights up, and it ceases to operate. In this case, be sure to take in water from a high water pressure place or locat a water tank (YX-09KBA1).
Page 32
Automatic TIG filler Connection with TIG-MATE YJ-1052THGE (Sold separately) Connect the TIG-MATE control cables as illustrated in drawing below. - 2 4 -...
PARTS LIST The No. of the table shows the location number of PARTS LAYOUT DRAWING (Spec. No. YC-500WY4/WX4HJE) Mark Name Code Q'ty Ammeter KFM7BDC600AK C, C Coup1ing coil TSMTU059 C21 , C 2 2 Capacitor ECG2WBP272MD116YA C36~C4 1 Capacitor MKP-C20UF350VDC CO 1 Receptacle(Remote control) MT25B7-01...
Page 38
The No. of the table shows the location number of PARTS LAYOUT DRAWING (space.No.YC-300WY4HJE) Mark Name Code Q’ty KFM7BDC300AK/KFM7BDC300AK Ammeter Coupling coil CLU00025 C18,C27 Capacitor ECG2WBP182MC122YA C23~26 Capacitor MKP-C20UF350VDC MT25B7-01 Receptacle(Remote control) MT25B2PM Receptacle(Torch switch) Current transformer HAS200-S/SP50/L03S200D15WM Diode DF60AA160 D2~5 FRS300BA50/MMF300YB050U...