Page 1
Operating Instructions MEW01228 Revision 1 Web512 V2.6.x for Web-server II, 1598 Author: Jan Pettersson Date of issue: 2009-09-21 Date of rev: 2011-08-12...
Page 2
This page has deliberately been left blank.
Panasonic Electric Works Nordic AB MEW01228 Rev: 1 Operating Instructions Web512 V2.6.x for Web-server II 1598 Table of contents Introduction________________________________ 5 Definitions / Explanations ____________________ 6 General description _________________________ 7 Web-server II, 1598 ________________________________ 8 Functions __________________________________ 9 Login ___________________________________________ 10 Sound Off, Help &...
Page 4
Panasonic Electric Works Nordic AB MEW01228 Rev: 1 Operating Instructions Web512 V2.6.x for Web-server II 1598 4.7.2 Search by Zone - Address _______________________ 23 4.7.3 Search by Limit _______________________________ 24 Event log ________________________________________ 25 4.8.1 General _____________________________________ 25 4.8.2 Alarm_______________________________________ 25 4.8.3...
Page 5
Panasonic Electric Works Nordic AB MEW01228 Rev: 1 Operating Instructions Web512 V2.6.x for Web-server II 1598 5.5.3 Tateco configuration ___________________________ 51 5.5.4 COM port configuration ________________________ 51 Users ___________________________________________ 53 5.6.1 User settings _________________________________ 53 Web Link ________________________________________ 54 CU Name ________________________________________ 55 FTP/SSL ________________________________________ 56 5.9.1...
Page 6
Panasonic Electric Works Nordic AB MEW01228 Rev: 1 Operating Instructions Web512 V2.6.x for Web-server II 1598...
Web-server II. The software (Web512) is downloaded at the same time as the configuration data to the Web-server II via a Config Tool (a PC program). The Config Tool is depending on the EBL system and the EBL software version.
Panasonic Electric Works Nordic AB MEW01228 Rev: 1 Operating Instructions Web512 V2.6.x for Web-server II 1598 Definitions / Explanations Definitions / explanations / abbreviations / etc. frequently used or not explained elsewhere in the document. C.i.e. Control and indicating equipment (=control unit; C.U.) C.U.
MEW01228 Rev: 1 Operating Instructions Web512 V2.6.x for Web-server II 1598 General description The Web-server II (1598) can be used with one, two, three or four of the following functions: 1. As a web-server when one EBL512 control unit or an EBL512...
Operating Instructions Web512 V2.6.x for Web-server II 1598 Web-server II, 1598 Figure 2. Web-server II, 1598. The Web-server II consists of a light grey plastic cabinet, which shall be vertically mounted on a DIN rail. The Web-server II has four interfaces.
Password are required or not required, to see the status information. Even if the Web-server II is to be used for status information only (User level 1), it is recommended to use User name and Password (i.e. "Anonymous login" is not recommended).
Panasonic Electric Works Nordic AB MEW01228 Rev: 1 Operating Instructions Web512 V2.6.x for Web-server II 1598 Login Username: Type the user name for the User level respectively. Password: Type the user password for the User level respectively. Click OK to open the Status – Summary view.
Panasonic Electric Works Nordic AB MEW01228 Rev: 1 Operating Instructions Web512 V2.6.x for Web-server II 1598 4.2.2 Help Click Help to open a help text. Regarding the user definable URL (web link) for the help text, see chapter "Language", page 50.
The page is continuously updated (approx. each 10 sec.). In case of inconsistency between the Web-server II and the EBL512 system a synchronization has to be done via EBL512 (menu H8/S10). See also chapter "Synchronize", page 34. After restart of the Web- server II is always a synchronization done (automatically).
Click Summary to return to the Status – Summary view. 4.4.1.2 Gateway Fault Value = Normal = There is no Web-server II external equipment communication fault. Value = Error = There is a Web-server II external equipment communication fault.
Panasonic Electric Works Nordic AB MEW01228 Rev: 1 Operating Instructions Web512 V2.6.x for Web-server II 1598 001-01 The Time (date & time), Zone – Address and Text (alarm text) are displayed. Source = Smoke, Heat, Multi, MCP, Exting. system or Other.
Panasonic Electric Works Nordic AB MEW01228 Rev: 1 Operating Instructions Web512 V2.6.x for Web-server II 1598 State = - Info: A hyperlink to open a document, a drawing etc. for more information regarding the alarm point. Camera: A hyperlink to a web camera.
Panasonic Electric Works Nordic AB MEW01228 Rev: 1 Operating Instructions Web512 V2.6.x for Web-server II 1598 4.4.8 Service signals Like menu H4/U6 and menu H8/S4 respectively. In case of one or more detectors having activated service signal to see the Status – Service List view.
Panasonic Electric Works Nordic AB MEW01228 Rev: 1 Operating Instructions Web512 V2.6.x for Web-server II 1598 Fault List In case of one or more faults (Value > 0), click Fault List (yellow font colour) or Faults (in the Status – Summary view) to view the Fault List view.
Panasonic Electric Works Nordic AB MEW01228 Rev: 1 Operating Instructions Web512 V2.6.x for Web-server II 1598 4.6.1 Zone Address. Click List to view the Disablement list – Zone Address view / list. The Time (date & time), Zone – Address, Re-enable time and Reason (e.g.
Panasonic Electric Works Nordic AB MEW01228 Rev: 1 Operating Instructions Web512 V2.6.x for Web-server II 1598 Click ReEnable to re-enable the disablement respectively. (Require log-in on User level 2 or higher.) If the list is "full" click Next to see the next list and Prev to see previous list.
Panasonic Electric Works Nordic AB MEW01228 Rev: 1 Operating Instructions Web512 V2.6.x for Web-server II 1598 ReEnable Click ReEnable to re-enable the disablement respectively. (Require log-in on User level 2 or higher.) If the list is "full" click Next to see the next list and Prev to see previous list.
Panasonic Electric Works Nordic AB MEW01228 Rev: 1 Operating Instructions Web512 V2.6.x for Web-server II 1598 ReEnable Click ReEnable to re-enable the disablement respectively. (Require log-in on User level 2 or higher.) If the list is "full" click Next to see the next list and Prev to see previous list.
Page 24
Panasonic Electric Works Nordic AB MEW01228 Rev: 1 Operating Instructions Web512 V2.6.x for Web-server II 1598 The Alert annunciation function can be disabled via menu H8/S6. Click Summary to return to the Disablement – Summary view.
Panasonic Electric Works Nordic AB MEW01228 Rev: 1 Operating Instructions Web512 V2.6.x for Web-server II 1598 Sensor list NOTE! Log in on User level > 2 is required. Click Sensor list to see the Sensor Information view. 4.7.1 Search by Tech. No.
Panasonic Electric Works Nordic AB MEW01228 Rev: 1 Operating Instructions Web512 V2.6.x for Web-server II 1598 If the list is "full" click Next to see the next list and Prev to see previous list. Click Sensor Menu to return to the Sensor Information view.
Panasonic Electric Works Nordic AB MEW01228 Rev: 1 Operating Instructions Web512 V2.6.x for Web-server II 1598 Event log Click Event log to see the Event log – General view. 4.8.1 General The Event log - General view / list (open as default):...
Panasonic Electric Works Nordic AB MEW01228 Rev: 1 Operating Instructions Web512 V2.6.x for Web-server II 1598 All Fire alarms, co-incidence alarms and pre-warnings will be logged. Up to 999 events in the list. If the list is "full" click Next to see the next list and Prev to see previous list.
Panasonic Electric Works Nordic AB MEW01228 Rev: 1 Operating Instructions Web512 V2.6.x for Web-server II 1598 Operation; Daily NOTE! Log in on User level 2, 3 or 4 is required. The Daily - Disablement view is default (User level 2). See below.
Panasonic Electric Works Nordic AB MEW01228 Rev: 1 Operating Instructions Web512 V2.6.x for Web-server II 1598 4.9.1.4 Alarm Devices Like menu H2/B9. All control outputs type "alarm device" can be collectively disabled / re-enabled (all at the same time) in all control units (99) or in a specified control unit (00-29).
Page 31
Panasonic Electric Works Nordic AB MEW01228 Rev: 1 Operating Instructions Web512 V2.6.x for Web-server II 1598 4.9.3.1 Inter. Output Like menu H9/C4 & C5. A specified interlocking combination (Area-Point) output can be disabled / re-enabled. 4.9.3.2 Activate Inter. Output Like menu H9/C2 & C3.
Panasonic Electric Works Nordic AB MEW01228 Rev: 1 Operating Instructions Web512 V2.6.x for Web-server II 1598 4.9.4 Misc Click Misc to see the Daily – Set Calendar and Time view. 4.9.4.1 Set Calendar and Time The Date (Year – Month – Date) can be typed or taken from your PC, see below.
Panasonic Electric Works Nordic AB MEW01228 Rev: 1 Operating Instructions Web512 V2.6.x for Web-server II 1598 A "fire alarm" for a specified alarm point can be sent from the Web- server II (EBLTalk) for testing purposes. Type a Zone-Address and click OK.
Panasonic Electric Works Nordic AB MEW01228 Rev: 1 Operating Instructions Web512 V2.6.x for Web-server II 1598 4.10 Operation; Maintenance NOTE! Log in on User level 2, 3 or 4 is required. The Daily - Disablement view is default (User level 2). See page 27.
Panasonic Electric Works Nordic AB MEW01228 Rev: 1 Operating Instructions Web512 V2.6.x for Web-server II 1598 The zone line input (0) on a specified COM loop unit / technical number (Tech. No.), can be disabled / re-enabled. 4.10.1.5 Fire routing equipment Like menu H8/S1.
Page 36
Panasonic Electric Works Nordic AB MEW01228 Rev: 1 Operating Instructions Web512 V2.6.x for Web-server II 1598 4.10.3.3 Activate Alarm Like menu H8/S9. A specified alarm point (Zone-Address) can be set in fire alarm mode. Reset the fire alarm like any other fire alarm, see chapter Alarm, page 13.
Panasonic Electric Works Nordic AB MEW01228 Rev: 1 Operating Instructions Web512 V2.6.x for Web-server II 1598 4.11 Operation; Service NOTE! Log in on User level 2, 3 or 4 is required. The Daily - Disablement view is default (User level 2). See page 27.
Panasonic Electric Works Nordic AB MEW01228 Rev: 1 Operating Instructions Web512 V2.6.x for Web-server II 1598 The communication direction for a specified BS4 Loop (0-3) on a specified expansion board 1584, Autronica interface Board (0-3), in a specified Control Unit (00-29) can be locked.
Panasonic Electric Works Nordic AB MEW01228 Rev: 1 Operating Instructions Web512 V2.6.x for Web-server II 1598 4.11.2.3 Relay Output A specified relay Output (R0-R1) in a specified Control Unit (00-29) can be activated. Click Set to activate the output. Click Reset to de-activate the output.
Page 40
Panasonic Electric Works Nordic AB MEW01228 Rev: 1 Operating Instructions Web512 V2.6.x for Web-server II 1598 The current consumption for a specified COM Loop (0-3) in a specified Control Unit (00-29) or all COM loops in all control units in the system can be displayed.
Panasonic Electric Works Nordic AB MEW01228 Rev: 1 Operating Instructions Web512 V2.6.x for Web-server II 1598 Click List to display the statistics for all COM loops in all control units in the system. 4.11.4 Password (Access code) The Service – Change password view: 4.11.4.1...
Click FTP / Telnet to see the Service – FTP / Telnet view: 4.11.6.1 FTP Access When a new site (incl. the Web-server II software) shall be downloaded to the Web-server II, an FTP Access User name and Password are always required.
Disablement Service Pre-warning Test mode Web log None selected (default) See chapter "General e-mail", page 46. 4.14 Gateway function The Web-server II, 1598 can also work as a gateway, see chapter "Gateway", page 51.
Framework has to be installed on your PC. More information and a free download are available on the Microsoft web site. The Web-server II and the PC both have to be connected to the Local Area Network (LAN). As an alternative a "Crossed network cable" or a Hub can...
Page 45
MEW01228 Rev: 1 Operating Instructions Web512 V2.6.x for Web-server II 1598 The Web-server II IP address is required and the FTP user name and password are required. When the upload is complete, the site will be in the Available sites...
Normally, at midnight every day, the Control Unit no. 00 in an EBL512 system will send out the date & time to synchronize the clock in all control units in the system as well as the clock in Web-server II. For continuous correct time and synchronization of all the clocks an server can be used.
Panasonic Electric Works Nordic AB MEW01228 Rev: 1 Operating Instructions Web512 V2.6.x for Web-server II 1598 Internet Explorer can be used, e.g. *.bmp, *.gif, *.jpg and *.wmf (< 10 Kbytes and max. 210 x 56 pixels). Max. 8 characters in the file name.
Panasonic Electric Works Nordic AB MEW01228 Rev: 1 Operating Instructions Web512 V2.6.x for Web-server II 1598 General e-mail 5.3.1 General e-mail configuration E-mail address for web-server: An e-mail address (name) is required for sending e-mails (e.g. Web512@pewfste.com). IP address for SMTP server: An SMTP server IP address is required.
Page 49
Panasonic Electric Works Nordic AB MEW01228 Rev: 1 Operating Instructions Web512 V2.6.x for Web-server II 1598 (Type Fire alarm selected.) Receiver(s): Up to four e-mail receivers can be written, separated by a comma (,) or a semicolon (;). Subject: An e-mail "Subject" text shall be written, e.g. "Fire alarm".
Page 50
NOTE! In the fault form there is the option: Send e-mail when no connection to EBL512. When this option is selected (default) and in case of no connection between the Web-server II and the EBL512 c.i.e. an e-mail will be sent to the same e-mail address(es) as for a fault e-mail and with the same body text.
Page 51
Panasonic Electric Works Nordic AB MEW01228 Rev: 1 Operating Instructions Web512 V2.6.x for Web-server II 1598 The technical number for the dirty detector (000001-293127) (BS4 unit: 004001-297399. Date & time, i.e. MM-DD hh:mm:ss (month-day hour : minute : second), e.g. 11-24 12:34:56 5.3.2.1.5...
Web512 II 2.6 is available on request. 5.4.2 Select web link for Help text Help text: Type the web link (URL) for help text to be opened when you click the Help button on the Web-server II page, see page 10.
(like the former "Tateco" Data converter 2291). EBL Talk. The Web-server II is also a gateway to a separate PC system, i.e. it will transmit and present fire alarm information in that system (like the former "EBL Talk" Data Converter 2292).
Page 54
Panasonic Electric Works Nordic AB MEW01228 Rev: 1 Operating Instructions Web512 V2.6.x for Web-server II 1598 5.5.4.2 Databit(s) 7 bits or 8 bits. 5.5.4.3 Stopbit(s) 1 bit or 2 bits. 5.5.4.4 Parity None, Odd or Even in the drop-down list.
Operating Instructions Web512 V2.6.x for Web-server II 1598 Users Even if the Web-server II is to be used for status information only (User level 1), it is recommended to have a User name and Password (i.e. "Anonymous login" is not allowed, see below).
NOTE! If for example the Prefix 1 checkbox is marked, the Prefix 1 text will be automatically added before the Web Link 1 text when the site is downloaded to the Web-server II but the Prefix 1 text will never be displayed in the Web Link 1 cell.
Panasonic Electric Works Nordic AB MEW01228 Rev: 1 Operating Instructions Web512 V2.6.x for Web-server II 1598 CU Name Instead of presenting each Control Unit as "Control Unit 00" etc. in the web page columns, the control units can have an informative Name, e.g.
Web-server II and restart of the Web-server II. 5.9.2 Select SSL Certificates When the Web-server II shall be used also for control of the EBL512 system, it is highly recommended to use the safe (encrypted) communication. Use SSL access: Select this option to create a safe (encrypted) communication with the EBL512 system.
Panasonic Electric Works Nordic AB MEW01228 Rev: 1 Operating Instructions Web512 V2.6.x for Web-server II 1598 5.10 Misc 5.10.1 Event Log The events are always presented in four different types of event logs, see below. Use Extended Log: This option is not selected as default.
Panasonic Electric Works Nordic AB MEW01228 Rev: 1 Operating Instructions Web512 V2.6.x for Web-server II 1598 NOTE! Normally all the events (see above) are saved in the Web- server. In case of a powerless Web-server all the events will be lost except the events saved in the Web-server's flash memory at midnight every day.
Panasonic Electric Works Nordic AB MEW01228 Rev: 1 Operating Instructions Web512 V2.6.x for Web-server II 1598 5.11 About Here, as well as in the Title bar, you can see the Web512 II Config Tool version, i.e. 2.6.5. The Web512 II Config Tool has to have the same version as the...
Calendar and Time", page 30. See also chapter "NTP Server", page As an alternative the PC can be connected directly to the Web-server II via a crossed network cable or a hub. The clock is also set automatically once a day at midnight. Also menu H3 in EBL512 can be used and the command will then be sent when you leave menu H3 by pressing "Accept", see EBL512 Operating Instruction.
New Web-server II software (S/W) cannot be downloaded separately. The Web-server II software (S/W) will be automatically downloaded when the site is downloaded to the Web-server II via the Web512 II Config Tool V2.6.x, see page 60. An old site (i.e. the file: xxxxxx.website) can be imported in a new Web512 II Config Tool version, saved and then downloaded.
The Web-server II has an RJ45 connector for a standard Ethernet CAT.5 cable, to be used to connect the Web-server II to Internet / an intranet (LAN). (The cable is not supplied.) The web-server has a 9 ways male "D" connector (RS232C), to be used to connect the Web-server II to a separate PC system, etc.
Page 65
Panasonic Electric Works Nordic AB MEW01228 Rev: 1 Operating Instructions Web512 V2.6.x for Web-server II 1598 3. In the PC program Web512 II Config Tool V2.6.x you have to prepare the S/W and site download as follows: a. In the "Site" tab page select a "site" (name) or click "New" to create a new site.
Panasonic Electric Works Nordic AB MEW01228 Rev: 1 Operating Instructions Web512 V2.6.x for Web-server II 1598 Connections For EBL512 see drawing 512-73. See also Web-server II 1598 Technical Description (MEW01035).
Panasonic Electric Works Nordic AB MEW01228 Rev: 1 Operating Instructions Web512 V2.6.x for Web-server II 1598 Revision history Revisions are when possible typed in red font colour. Most of the pictures are updated. Info added. 4.2.3 Info added. Info added & revised.
Page 68
Panasonic Electric Works Nordic AB MEW01228 Rev: 1 Operating Instructions Web512 V2.6.x for Web-server II 1598...
Page 69
This page has deliberately been left blank.
Page 70
Panasonic Electric Works Nordic AB Jungmansgatan 12, SE-211 19 Malmö, Sweden Tel: +46 (0)40 697 70 00 • Fax: +46 (0)40 697 70 99 info-fste@eu.pewg.panasonic.com • www.panasonic-fire-security.com...