1. Manuals
  2. Brands
  3. HP Manuals
  4. Desktop
  5. Kayak XA05
  6. Installation manual

HP Kayak XA05 Installation Manual

Pc workstation
Hide thumbs Also See for Kayak XA05:
Table of Contents

Advertisement

Quick Links

Download this manual See also: User Manual
HP Kayak XA 05xx PC Workstation —
Installing Accessories
In Your HP Desktop PC Workstation
Explains in detail how to install accessories, such as extra memory,
accessory boards, and additional disk drives.

Advertisement

Table of Contents
loading

Related Manuals for HP Kayak XA05

Summary of Contents for HP Kayak XA05

  • Page 1 HP Kayak XA 05xx PC Workstation — Installing Accessories In Your HP Desktop PC Workstation Explains in detail how to install accessories, such as extra memory, accessory boards, and additional disk drives.

  • Page 2: Supported Hp Accessories

    HP Kayak XA 05xx PC Workstation — Installing Accessories In Your HP Desktop PC Workstation Supported HP Accessories Supported HP Accessories Main Memory Upgrade DIMM slots for 100 MHz SDRAM: - 32 MB SDRAM (D6521A) - 64 MB SDRAM (D6522A)

  • Page 3: Removing And Replacing The Cover

    HP Kayak XA 05xx PC Workstation — Installing Accessories In Your HP Desktop PC Workstation Removing and Replacing the Cover WARNING For your safety, never remove the PC Workstation’s cover without first removing the power cord from the power outlet, and any connection to a telecommunications network.
  • Page 4 HP Kayak XA 05xx PC Workstation — Installing Accessories In Your HP Desktop PC Workstation Removing and Replacing the Cover Replacing the Cover 1 Ensure that you have installed all your accessories and that all internal cables are properly connected and safely routed.

  • Page 5: Moving The Power Supply

    HP Kayak XA 05xx PC Workstation — Installing Accessories In Your HP Desktop PC Workstation Moving the Power Supply 1 Disconnect the computer’s power cord and any LAN cable. 2 Remove the computer’s cover (refer to page 3). 3 Lift the front of the power supply up and move it forwards to disengage the hinge on the rear.
  • Page 6 HP Kayak XA 05xx PC Workstation — Installing Accessories In Your HP Desktop PC Workstation Moving the Power Supply Replacing the Power 1 Check that all internal cables are safely routed. Supply after Installing 2 Rotate the power supply into the computer. Tilt the back of the Accessories power supply unit until it engages with the computer’s case.

  • Page 7: Installing Memory

    HP Kayak XA 05xx PC Workstation — Installing Accessories In Your HP Desktop PC Workstation Installing Memory Main Memory Modules If you need more main memory to run your application software, you can install up to 768 MB of memory in three 100 MHz DIMM slots.
  • Page 8 HP Kayak XA 05xx PC Workstation — Installing Accessories In Your HP Desktop PC Workstation Installing Memory 4 Remove the fan underneath and place it on top of the power supply. The location of the memory module slots is shown below.
  • Page 9 HP Kayak XA 05xx PC Workstation — Installing Accessories In Your HP Desktop PC Workstation 6 Firmly press the memory module completely into the connector until the retaining clips click into position. 7 Repeat this procedure for each additional memory module you want to install.

  • Page 10: Installing Mass Storage Devices

    HP Kayak XA 05xx PC Workstation — Installing Accessories In Your HP Desktop PC Workstation Installing Mass Storage Devices Installing Mass Storage Devices Connecting Devices If you add an IDE Zip drive, hard disk drive, CD-ROM drive, CD-RW drive, or tape drive, you need to connect it to power and data cables.
  • Page 11 HP Kayak XA 05xx PC Workstation — Installing Accessories In Your HP Desktop PC Workstation Before Installing an Refer to the drive’s installation guide to see if you must set jumpers or if there is a special installation procedure to follow.
  • Page 12 HP Kayak XA 05xx PC Workstation — Installing Accessories In Your HP Desktop PC Workstation Installing Mass Storage Devices Installing a Hard Disk Drive in an Internal Shelf NOTE The internal shelves can house one hard disk drive that is up to 1.6 inches in height, and one hard disk drive of up to 1 inch in height.
  • Page 13 HP Kayak XA 05xx PC Workstation — Installing Accessories In Your HP Desktop PC Workstation 7 If you want to install the new hard drive in the shelf of the existing drive, remove the four retaining screws from the top of the hard drive’s unit and remove the drive.
  • Page 14 HP Kayak XA 05xx PC Workstation — Installing Accessories In Your HP Desktop PC Workstation Installing Mass Storage Devices 9 For a drive in the upper shelf, tighten the four retaining screws on top of the hard drive unit. For a drive in the lower shelf, use the four spare screws from the top (center) of the hard drive unit, to secure the hard disk drive on either side.

  • Page 15: Completing The Installation Of A Hard Disk Drive

    HP Kayak XA 05xx PC Workstation — Installing Accessories In Your HP Desktop PC Workstation 11 Lower the hard drive unit back into the PC Workstation’s case and tighten the four (outer) retaining screws. 12 Install any other accessories before completing the installation.

  • Page 16: Installing A Drive In A Front-Access Shelf

    HP Kayak XA 05xx PC Workstation — Installing Accessories In Your HP Desktop PC Workstation Installing Mass Storage Devices When an IDE Drive 1 Switch on the computer. Is Installed 2 To display the device in POST, press Esc while the PC Workstation re-starts.
  • Page 17 HP Kayak XA 05xx PC Workstation — Installing Accessories In Your HP Desktop PC Workstation 3 Remove the metal filler plate from the front of the PC Workstation’s case. 4 Press the retaining buttons on each side of the HP UltraFlow airflow guide and remove it from the PC Workstation’s case.
  • Page 18 HP Kayak XA 05xx PC Workstation — Installing Accessories In Your HP Desktop PC Workstation Installing Mass Storage Devices 6 Slide the drive into the drive shelf and secure it. 7 Locate the appropriate data cable for the drive (refer to page 10).
  • Page 19 HP Kayak XA 05xx PC Workstation — Installing Accessories In Your HP Desktop PC Workstation 10 Remove the plastic panel from the cover by pulling the panel from the left and unhinging its right-hand side. Store the panel in a safe place.

  • Page 20: Installing Accessory Boards

    HP Kayak XA 05xx PC Workstation — Installing Accessories In Your HP Desktop PC Workstation Installing Accessory Boards Installing Accessory Boards CAUTION Static electricity can damage electronic components. Turn OFF all equipment. Don’t let your clothes touch the accessory. To equalize the static electricity, rest the accessory bag on top of the computer while you are removing the accessory from the bag.
  • Page 21 HP Kayak XA 05xx PC Workstation — Installing Accessories In Your HP Desktop PC Workstation 4 Unscrew and remove the slot cover. Store it in a safe place. If the slot cover is tight, loosen the screws on the adjacent slots.
  • Page 22 HP Kayak XA 05xx PC Workstation — Installing Accessories In Your HP Desktop PC Workstation Installing Accessory Boards Completing the If you have installed an ISA accessory board that uses an interrupt, you must run the Setup program and reserve the IRQ for the accessory Installation of an ISA board.

Table of Contents