ENGLISH SMALL ANGLE GRINDERS DWE4202, DWE4203, DWE4204, DWE4205, DWE4206, DWE4207, DWE4213, DWE4214, DWE4215, DWE4216, DWE4217 Congratulations! You have chosen a D WALT tool. Years of experience, thorough product development and innovation make WALT one of the most reliable partners for professional power tool users.
Never modify the plug in any way. Do not use any adapter plugs with earthed SMALL ANGLE GRINDERS (grounded) power tools. Unmodified plugs DWE4202, DWE4203, DWE4204, DWE4205, DWE4206, and matching outlets will reduce risk of DWE4207, DWE4213, DWE4214, DWE4215, DWE4216, electric shock.
ENGLISH Use personal protective equipment. that may affect the power tool’s operation. Always wear eye protection. Protective If damaged, have the power tool repaired equipment such as dust mask, non-skid before use. Many accidents are caused by safety shoes, hard hat, or hearing protection poorly maintained power tools.
ENGLISH diameter of the flange. Accessories that do n) Regularly clean the power tool’s air vents. not match the mounting hardware of the power The motor’s fan will draw the dust inside tool will run out of balance, vibrate excessively the housing and excessive accumulation of and may cause loss of control.
ENGLISH c) Do not position your body in the area where Additional Safety Warnings Specifi c power tool will move if kickback occurs. for Abrasive Cutting-Off Operations Kickback will propel the tool in direction opposite to the wheel’s movement at the point a) Do not "jam"...
These are: e. Threaded locking flange – Impairment of hearing. f. Guard – Risk of personal injury due to flying particles. g. Slider switch (DWE4204, DWE4205, DWE4206, – Risk of burns due to accessories becoming hot DWE4207, DWE4214, DWE4215, DWE4216, during operation. DWE4217) –...
NTENDED USE Your D WALT tool is double insulated in accordance with EN 60745; therefore no The DWE4202, DWE4203, DWE4204, DWE4205, earth wire is required. DWE4206, DWE4207, DWE4213, DWE4214, DWE4215, DWE4216 and DWE4217 heavy- If the supply cord is damaged, it must be replaced...
(fig. 4). this grinder. 3. Place the disc (p) on the backing flange (d). When using the DWE4202, DWE4203, DWE4204, When fitting a disc with a raised centre, make DWE4205, DWE4206, DWE4207, DWE4213, sure that the raised centre (q) is facing the DWE4214, DWE4215, DWE4216 or the DWE4217 backing flange (d).
ENGLISH 8. To remove the disc, loosen the threaded locking 7. Release the spindle lock. flange (e) with the hex key (s) provided or a two 8. To remove the rubber backing pad, loosen the pin spanner. threaded clamp nut (r) with the hex key provided or a two pin spanner.
Page 15
SLIDER SWITCH (FIG. 3) • Apply only a gentle pressure to the (DWE4204, DWE4205, DWE4206, DWE4207, DWE4214, tool. Do not exert side pressure on DWE4215, DWE4216, DWE4217) the disc. WARNING: Before connecting the tool •...
Page 16
ENGLISH Spindle Lock (fi g. 1) 1. Allow the tool to reach full speed before touching the tool to the work surface. The spindle lock (a) is provided to prevent the 2. Apply minimum pressure to the work surface, spindle from rotating when installing or removing allowing the tool to operate at high speed.
Page 17
ENGLISH CAUTION: Use extra care when 3. NO EATING, DRINKING or SMOKING should working over an edge, as a sudden be done in the work area to prevent ingesting sharp movement of grinder may contaminated paint particles. Workers should be experienced. wash and clean up BEFORE eating, drinking or smoking.
ENGLISH Cutting Metal MAINTENANCE When cutting, work with moderate feed, adapted to Your D WALT power tool has been designed to the material being cut. Do not exert pressure onto operate over a long period of time with a minimum the cutting disc, tilt or oscillate the machine.
ENGLISH Optional Accessories WALT provides a facility for the collection and recycling of D WALT products once they have WARNING: Since accessories, other reached the end of their working life. To take than those offered by D WALT, have advantage of this service please return your product not been tested with this product, use to any authorised repair agent who will collect them of such accessories with this tool could...
Page 20
ENGLISH GRINDING AND CUTTING ACCESSORY CHART Guard Type Accessory Description How to Fit Grinder Depressed centre grinding disc TYPE 27 Type 27 guard GUARD Flap wheel Backing flange Wire wheels Type 27 depressed centre wheel Threaded clamp nut Wire wheels with threaded Type 27 guard Wire wheel...
Page 21
ENGLISH GRINDING AND CUTTING ACCESSORY CHART (cont.) Guard Type Accessory Description How to Fit Grinder Masonry cutting disc, bonded TYPE 1 Type 1 guard GUARD Metal cutting disc, bonded Backing flange Diamond cutting wheels TYPE 1 Cutting wheel GUARD Threaded clamp nut TYPE 27 GUARD...
Page 24
Belgique et WALT - Belgium BVBA Tel: NL 32 15 47 37 63 www.dewalt.be Luxembourg België Egide Walschaertsstraat 16 Tel: FR 32 15 47 37 64 enduser.BE@SBDinc.com en Luxemburg 2800 Mechelen Fax: 32 15 47 37 99 Danmark WALT Tel: 70 20 15 10 www.dewalt.dk...