Page 1
Order No. MD0102028C1 Portable Stereo CD System RX-D13 Color (A) ... Blue Type (R) ... Red Type (S) ... Silver Type P ... U.S.A. PC ... Canada Tape Deck: SG20 Mechanism Series Traverse Deck: RAE0152Z-1C Mechanism Series SPECIFICATIONS...
Page 2
RADIO Frequency Range 87.9-107.9 MHz (200 kHz steps) 87.5-108.0 MHz (100 kHz steps) 520-1710 kHz (10 kHz steps) Intermediate Frequency 450 kHz 10.7 MHz Sensitivity 46 dB/m/50 mW 15 dB/50 mW TAPE RECORDER Track System 4 track, 2 channel, stereo Monitor system Variable sound monitor Recording system...
Page 3
Notes: 1. Specifications are subject to change without notice. 2. Mass and dimensions are approximate. 2001 Matsushita Electronics (S) Pte. Ltd. All rights reserved. Unauthorized copying and distribution is a violation of law. 1. Safety Precaution (This “Safety Precaution” is applied only in U.S.A.) 1.
Page 4
design. These will read infinity. 4. If the measurement is outside the specified limits, there is a possibility of a shock hazard. The equipment should be repaired and rechecked before it is returned to the customer.
Page 5
Battery Service Life UM-1 (D-size) Batteries / Approximately 30 hrs of Tape Recording. (EIAJ) / Approximately 16 hrs of Tape Playback. (EIAJ) / Approximately 11.5 hrs of CD Recording. (EIAJ) / Approximately 10.5 hrs of CD Playback. (EIAJ) The battery service life is measured according to the conditions set forth by EIAJ. (Electronic Industries Association of Japan).
Page 6
1. Turn off the power. 2. Determine the cause of the problem and correct it. 3. Turn on the power once again after one minute. Note: When the protection circuitry functions, the unit will not operate unless the power is first turned off and then on again.
Page 7
5. Handling Precautions For Traverse Deck The laser diode in the traverse deck (optical pickup) may break down due to potential difference caused by static electricity of clothes or human body. So, be careful of electrostatic breakdown during repair of the traverse deck (optical pickup). - Handling of traverse deck (optical pickup) 1.
Page 8
2. To prevent the breakdown of the laser diode, an antistatic shorting pin is inserted into the flexible board (FFC board). 3. Take care not to apply excessive stress to the flexible board (FFC board). When removing or connecting the short pin, finish the job in as short time as possible.
Page 9
6. Precaution of Laser Diode Caution: This unit utilizes a class 1 laser. Invisible laser radiation is emitted from the optical pickup lens. When the unit is turned on: 1. Do not look directly into the pickup lens. 2. Do not use optical instruments to look at the pickup lens. 3.
Page 10
8. Self-Diagnostic Functions 8.1. Setting of the Self-Diagnostic Mode 1. Switch the SELECTOR to CD and set to TAPE STOP state. (CD PLAY STOP) 2. Press the /CLEAR for the first two seconds and followed by the FAST FORWARD keys for another two seconds without releasing /CLEAR key, it shall enter into the Self-Diagnostic mode.
Page 11
3. At the state of [ T ] display, operate as follows: - Open the CD lid and close it right away. - Start recording TAPE, and STOP it at once. 4. Press /CLEAR key. - Self diagnostic results, i.e. the memorized errors during actual operations and the result of above-mentioned operation shall be displayed alternately.
Page 12
Abnormal Items Error Method of detection Display CLOSE SW abnormal Detect error during closing operation and memorised as an error. REST SW abnormal Under normal operation (Self-Diagnostic Mode inclusive), this error occurs when the REST SW not detected within the specified time (5000 ms) shall be memorised.
Page 13
........................P.g.12 2. Installation of the CD Servo P.C.B. after Replacement ....................P.g.13 Warning: This product uses a laser diode. Refer to. 9.1. Checking Procedure for each major P.C.B. 9.1.1. Checking for the Main, Panel, Tuner, Power & Cd Servo P.C.B Step 1: Remove all the screws.
Page 14
Step 4: Remove all the screws and take out the Remote Sensor Panel. Step 5: Press STOP/EJECT button to release the cassette lid and pull the back cabinet as direction shown. Step 6: Release the connector CP601.
Page 15
Step 7: Release the connectors CP307 and CS309. Step 8: Pull down all the catches to remove the Panel P.C.B. Step 9: Unscrew all the screws. Remove the Panel P.C.B. Holder. Step 10: Release the connector W301.
Page 16
Step 11: Remove all the screws. Step 12: Pull the CD unit as direction shown. Step 13: Remove all the screws from Main P.C.B.. Rconnect back all connectors and wires to do the testing. 9.2. Main Component Replacement Procedures...
Page 17
9.2.1. Replacement of the Traverse Deck Step 2: Desolder the 4 legs of the 2 motors and pull out the Servo P.C.B. Step 3: Widen the 3 bosses with a flat screwdriver and pull out the 3 pins. Then remove the Traverse Deck.
Page 18
Step 4: Remove the flexible cable CN701. - Removal of the flexible cable. Push the top of the connector in the direction of the arrow 1, and the pull out the flexible cable in the direction of the arrow 2. 9.2.2.
Page 19
Note : Before installing the CD servo P.C.B., move the optical pickup towards the outer edge from the marking (black triangle). [Otherwise, the detect switch (S701) mounted on the CD servo P.C.B. may be damaged.] 10. Schematic Diagram (All schematic diagrams may be modified at any time with the development of new technology.) Notes: S702 Open Switch...
Page 20
some error in voltage values and waveforms depending upon the internal impedance of the tester or the measuring unit. No mark ...Playback < > ...FM (( )) ...CD ...AM - Importance safety notice: Components identifed by mark have special characteristics important for safety.
Page 30
SCHEMATIC DIAGRAM-1 CD SERVO CIRCUIT : +B Signal line : CD Signal line R716 R712 C728 50V2.2 IC 701 BA6770FS R710 22K RF HEAD AMP IC ((0.12V)) ((1.71V)) R720 ((1.70V)) ((1.26V)) 100K R713 ((1.70V)) ((1.69V)) 220K ((1.70V)) ((0V)) Q701 ((0V)) ((0V)) R715 ((3.13V))
Page 31
SCHEMATIC DIAGRAM-5 : Rec Signal line DECK CIRCUIT : Playback Signal Line : +B Signal Line R1103 220K R1203 220K IC1001 SW1001 SW1001 IC1001 BA3313L PRE-AMP IC CP1001 R1002 R. BIAS R1101 R1003 C1101 2700P L1001 D1002 Q1001 C1001 2.34V R1006 E.HD C1003...
Page 32
SCHEMATIC DIAGRAM-6 : Rec Signal line : Playback Signal Line : +B Signal Line REC_IN_L REC_IN_R REC_H PB_OUT_L MAIN CIRCUIT (W305) ON PB_OUT_R SCHEMATIC DIAGRAM-2 7.5V GND(SIGNAL) TAPE_H GND(MOTOR) W305 R1105 2.2K C1103 R1104 0.022 5.6K R108 5.6K SW1002 L310 RM301 R208 5.6K...
Page 33
SCHEMATIC DIAGRAM-2 MAIN CIRCUIT : Main Signal line : AM/FM Signal line W303 W303 : CD Signal line S702 : Playback Signal line OP/CL OPEN-SW : Rec Signal line : +B Signal line ((0V)) R788 <0V> (0V) 3.32V ((3.31V)) <3.31V> (3.31V) 3.32V ((3.31V)) R789...
Page 39
SCHEMATIC DIAGRAM-3 : AM Signal line : AM/FM Signal line : FM Signal line TUNER CIRCUIT : +B Signal line : AM OSC Signal line TELESCOPIC ANTENNA 0.022 620P SVC384T-AL 50V1 100K 100K 3.3K 1000P R9 100K 2.2P 1000P 0.022 2.2K 1000P <0.92>...
Page 40
SCHEMATIC DIAGRAM-4 : AM/FM Signal line : +B Signal line LC72121T PLL IC 50V10 0.01 RLQZPR22KT-Y 2.2K 50V2.2 4.7K RLQA101KT-G 4.7K 2200P 16V100 0.01 1000P 3.3K C58 1000P 16V100 330P W304 TO MAIN CIRCUIT (W304) ON SCHEMATIC DIAGRAM-2...
Page 42
14. Measurements and Adjustments 14.1. Tuner Section...
Page 43
READ CAREFULLY BEFORE ATTEMPTING ALIGNMENT 1. Set volume control to maximum. 2. Set power source voltage to 9V. 3. Output of signal generator should be no higher than necessary to obtain an output reading. AM-RF ALIGNMENT Signal Generator or Sweep Radio Dial Indicator (Electronic Adjustment /...
Page 44
CAUTION : Please remove the screw-locking bond left on the head base when replacing the azimuth screw. After the adjustment, apply screwlock to the azimuth adjusting screw. ( Screw-locking bond: RZZ0L01) TAPE SPEED ALIGNMENT Test Tape Equipment Connection Adjustment Specification Remarks Electronic Counter ATT-111N Headphone Jack (32...
Page 45
3. Adjust L1001 so that the output frequency is within the standard value. Standard Value : 56kHz ± 7 kHz 14.2. CD Section Alignment is unneccessary for CD section of this unit. 14.2.1. Alignment Points...
Page 46
15. Type Illustrations of ICs, Transistors & Diodes 16. Terminal Functions of ICs - IC701 (BA6770FS) RF Head Amp...
Page 47
Mark Function I RF summing amplifier return input pin O LOOP ON voltage output pin I B+D input pin I A+C input pin I Tracking error bias input pin I Focus bias input pin O Bias amplifier output pin - GND pin I E input pin I F input pin O APC amplifier outpin...
Page 48
for AGC time constant Mark Function I RF output capacity connection re-input pin O RF summing amplifier output pin - IC702 (BU18527KS) Microprocessor Mark Function FDOUT O Focus drive out JUMPO O Tracking jump out TDOUT O Tracking drive out SDIN I SDIN SDOUT...
Page 49
Mark Function FBR_ADJ I/O Focus adjustment OPN_SW I/O Open/close switch REST SW I/O CD limit SW input for the most inner point SEL_IN I/O Selector input CD_SEL I/O CD mode select in TAPE_SEL I/O Tape mode select in 35 TUNER_SEL I/O Tuner mode select in I To ground P_CNT I/O Power control...
Page 50
Mark Function AGND - Analog ground RVCO I Pin with VCO oscillation frequency setting resistance I Focus OK output FEIN I Focus error FCAP O Focus LPF capacitor connection O Focus on TEIN I Tracking error I Anti-shock input I Tracking zero cross input TCAP O Tracking LPF capacitor connection...
Page 51
Mark Function O Motor driver (3) reverse - action output O Motor driver (3) forward - action output O Motor driver (4) reverse - action output O Motor driver (4) forward - action output PVCC2 I Power supply (2) for driver PGND2 - Ground connection (2) for driver...
Page 52
- The marking (RTL) indicates that the Retention Time is limited for this item. After the discontinuation of this assembly in production, the item will continue to be available for a specific period of time. The retention period of availability is dependant on the type of assembly, and in accordance with the lows govening part and product retention.
Page 54
Ref. No. Part No. Part Name & Description Remarks CASSETTE DECK RDV0021 MAIN BELT ‘D’ RMB0109-1 BRAKE SPRING RML0116 BRAKE RBR2CY009 ERASE HEAD RDG0057-1 IDLER GEAR RDG0059 FF RELAY GEAR RDK0005-1 CAM GEAR RDV0006-1 RF BELT RHW16009 CAPSTAN WASHER RMA0109 BACK PLATE RMB0043-1 ROD OPERATION SPRING...
Page 55
Ref. No. Part No. Part Name & Description Remarks RXR0005 SUPPLY REEL ASSY XTN2+6J BACK PLATE SCREW RHD26002 MOTOR SCREW XTN2+8F R/P SCREW RMG0102-1 MOTOR RUB. CUSHION RFKPXD13PC-A DC MOTOR ASS’Y RMA0108 MOTOR BK XTN26+8J MOTOR BK SCREW RME0098-2 E SLIDE LEVER SPRING RJR0033 EARTH LUG RML0080-1...
Page 56
17.2.2. Cabinet & CD Loading Machanism Parts List...
Page 57
Ref. No. Part No. Part Name & Description Remarks CABINET AND CHASSIS RAS10P30-G SPEAKER RDG0288 DAMPER GEAR REEX0109 PANEL TO MAIN FFC REEX0110 CD FFC WIRE (25P) REXX0141 TAPE HEAD WIRE REXX0244 SPEAKER WIRE RGKX0075-A CD LID RGKX0075-R CD LID [M]P-R RGKX0075-H CD LID...
Page 58
Ref. No. Part No. Part Name & Description Remarks RMXX0002-1 SPACER RWJ8902060SS MOTOR WIRE XEARR210CA-C ROD ANTENNA XTN2+14G SCREW XTN2+3F SCREW XTN3+12GFZ SCREW (TOP CAB) XTV3+10G SCREW (SPEAKER) XTV3+12G SCREW XTV3+20G REAR CAB SCREW XYN3+F15FY SCREW XTN3+8C SCREW RGKX0093-A CD LID LASER COVER RGKX0093-R CD LID LASER COVER [M]P-R...
Page 59
Ref. No. Part No. Part Name & Description Remarks P.C.B. REPW0010A1 BATTERY (1) P.C.B./BATTERY (2) P.C.B. [M]RTL P REPW0010B1 BATTERY (1) P.C.B./BATTERY (2) P.C.B. [M]RTL PC REPW0010A2 DECK P.C.B. [M]RTL P REPW0010B2 DECK P.C.B. [M]RTL PC REPW0010A3 CD SERVO P.C.B. [M]RTL P REPW0010B3 CD SERVO P.C.B.
Page 70
/ Printed in Singapore / M010200001FLE/H/C/D/J...
Page 71
(S) ... Silver Type P ... U.S.A. Tape Deck: SG20 Mechanism Series Traverse Deck: RAE0152Z-1C Mechanism Series Change the Version (A6) to (J1) (Correction) Please delete the RX-D13(P) (A6) version ( Order No. MD0102028C1) and use this supplement manual (J1) version. SPECIFICATIONS...
Page 72
RADIO Frequency Range 87.9-107.9 MHz (200 kHz steps) 87.5-108.0 MHz (100 kHz steps) 520-1710 kHz (10 kHz steps) Intermediate Frequency 450 kHz 10.7 MHz Sensitivity 46 dB/m/50 mW 15 dB/50 mW TAPE RECORDER Track System 4 track, 2 channel, stereo Monitor system Variable sound monitor Recording system...
Page 73
Notes: 1. Specifications are subject to change without notice. 2. Mass and dimensions are approximate. 2001 Matsushita Electronics (S) Pte. Ltd. All rights reserved. Unauthorized copying and distribution is a violation of law. 1. Location of Controls...
Page 74
Battery Service Life UM-1 (D-size) Batteries / Approximately 30 hrs of Tape Recording. (EIAJ) / Approximately 16 hrs of Tape Playback. (EIAJ) / Approximately 11.5 hrs of CD Recording. (EIAJ) / Approximately 10.5 hrs of CD Playback. (EIAJ) The battery service life is measured according to the conditions set forth by EIAJ. (Electronic Industries Association of Japan).
Page 75
S702 Open Switch S703 Rest Switch SW302 Function Switch SW601 Auto Scan Switch SW602 XBS/TONE/HES Switch SW603 Play Mode Switch SW604 Memory Switch SW605 REV Skip Switch SW606 FWD Skip Switch SW607 Play/Pause Switch SW608 CD Stop Switch SW1001 Record Switch SW1002 Leaf Switch VR301 Volume VR...
Page 76
Caution! IC, LSI and VLSI are sensitive to static electricity. Secondary trouble can be prevented by taking care during repair. - Cover the parts boxes made of plastics with aluminium foil. - Put a conductive mat on the work table. - Ground the soldering iron.
Page 77
SCHEMATIC DIAGRAM-1 CD SERVO CIRCUIT : +B Signal line : CD Signal line R716 R712 C728 50V2.2 IC 701 BA6770FS R710 22K RF HEAD AMP IC ((0.12V)) ((1.71V)) R720 ((1.70V)) ((1.26V)) 100K R713 ((1.70V)) ((1.69V)) 220K ((1.70V)) ((0V)) Q701 ((0V)) ((0V)) R715 ((3.13V))
Page 78
SCHEMATIC DIAGRAM-5 : Rec Signal line DECK CIRCUIT : Playback Signal Line : +B Signal Line R1103 220K R1203 220K IC1001 SW1001 SW1001 IC1001 BA3313L PRE-AMP IC CP1001 R1002 R. BIAS R1101 R1003 C1101 2700P L1001 D1002 Q1001 C1001 2.34V R1006 E.HD C1003...
Page 79
SCHEMATIC DIAGRAM-6 : Rec Signal line : Playback Signal Line : +B Signal Line REC_IN_L REC_IN_R REC_H PB_OUT_L MAIN CIRCUIT (W305) ON PB_OUT_R SCHEMATIC DIAGRAM-2 7.5V GND(SIGNAL) TAPE_H GND(MOTOR) W305 R1105 2.2K C1103 R1104 0.022 5.6K R108 5.6K SW1002 L310 RM301 R208 5.6K...
Page 80
SCHEMATIC DIAGRAM-2 MAIN CIRCUIT : Main Signal line : AM/FM Signal line W303 W303 : CD Signal line S702 : Playback Signal line OP/CL OPEN-SW : Rec Signal line : +B Signal line ((0V)) R788 <0V> (0V) 3.32V ((3.31V)) <3.31V> (3.31V) 3.32V ((3.31V)) R789...
Page 86
SCHEMATIC DIAGRAM-3 : AM Signal line : AM/FM Signal line : FM Signal line TUNER CIRCUIT : +B Signal line : AM OSC Signal line TELESCOPIC ANTENNA 0.022 620P SVC384T-AL 50V1 100K 100K 3.3K 1000P R9 100K 2.2P 1000P 0.022 2.2K 1000P <0.92>...
Page 87
SCHEMATIC DIAGRAM-4 : AM/FM Signal line : +B Signal line LC72121T PLL IC 50V10 0.01 RLQZPR22KT-Y 2.2K 50V2.2 4.7K RLQA101KT-G 4.7K 2200P 16V100 0.01 1000P 3.3K C58 1000P 16V100 330P W304 TO MAIN CIRCUIT (W304) ON SCHEMATIC DIAGRAM-2...
Page 88
Ar : Arabic Cf : Canadian French Cz : Czech Da : Danish Du : Dutch En : English Fr : French Ge : German It : Italian Ko : Korean Po : Polish Ru : Russian Sp : Spanish Sw : Swedish Co : Traditional Chinese Cn : Simplified Chinese 4.1.
Page 89
/ Printed in Singapore / M010400001FLE/E...