Husqvarna AUTOMOWER 310 Operator's Manual page 32
Hide thumbs
Also See for AUTOMOWER 310:
- Operator's manual (121 pages) ,
- Technical manual (100 pages) ,
- Quick manual (8 pages)
Table of Contents
Advertisement
To get access to the menu
1.
Do steps 1–3 in
on page 24 .
2.
Use the arrow buttons and the OK button to
move through the menu structure
Spiral Cutting > Use Spiral Cutting .
3.
Push the BACK button.
To set the level of Spiral Cutting
1.
Do steps 1–3 in
To get access to the menu
on page 24 .
2.
Use the arrow buttons and the OK button to
move through the menu structure
Spiral Cutting > Use Spiral Cutting >
Intensity .
3.
Use the left arrow button to select the level
of the Spiral Cutting.
4.
Push the BACK button.
3.10.12.3 Slope control
In order to decrease lawn wear near the
boundary wire in slopes, the product prevents to
move in the opposite direction when the product
Slope control is enabled in
operates in a slope.
the factory settings.
To set the Slope control
To get access to the menu
1.
Do steps 1–3 in
on page 24 .
2.
Use the arrow buttons and the OK button to
move through the menu structure
Slope control > Use Slope control .
3.
Push the BACK button.
3.10.13 General
General you can change the general settings
In
of the product.
3.10.13.1 To set the time & date
1.
Do steps 1–3 in
To get access to the menu
on page 24 .
2.
Use the arrow buttons and the OK button to
move through the menu structure
General > Time & Date .
3.
Use the number buttons to set the time and
then push the BACK button.
4.
Use the number buttons to set the date and
then push the BACK button.
5.
Use the arrow buttons to set the time format
and then push the BACK button.
32 - Installation
6.
Use the arrow buttons to set the date format
and then push the BACK button.
3.10.13.2 To set the language
Settings >
1.
Do steps 1–3 in
on page 24 .
2.
Use the arrow buttons and the OK button to
move through the menu structure
General > Language.
3.
Use the arrow buttons to select language
and then push the BACK button.
Settings >
3.10.13.3 To set the Country & Timezone
1.
Do steps 1–3 in
on page 24 .
2.
Use the arrow buttons and the OK button to
move through the menu structure
General > Country & Timezone.
3.
Use the arrow buttons to select country and
then push the BACK button.
3.10.13.4 To set the unit format
1.
Do steps 1–3 in
on page 24 .
2.
Use the arrow buttons and the OK button to
move through the menu structure
General > Unit format.
3.
Use the arrow buttons to select unit format
and then push the BACK button.
Settings >
3.10.13.5 To reset all user settings
1.
Do steps 1–3 in
on page 24 .
2.
Use the arrow buttons and the OK button to
move through the menu structure
General > Reset all user settings .
3.
Use the right arrow button to select
with reset of all user settings?
4.
Push the OK button to reset all the user
settings.
Settings >
Security level, PIN code, Loop signal,
Note:
Messages, Date & Time, Language and Country
settings are not reset.
3.10.13.6 The About menu
About menu displays information about the
The
product, for example serial number and firmware
versions.
To get access to the menu
Settings >
To get access to the menu
Settings >
To get access to the menu
Settings >
To get access to the menu
Settings >
Proceed
1440 - 003 - 09.03.2020
Advertisement
Table of Contents
