Sealey CP1202 Instructions

Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these
instructions, and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
Refer to Wear eye
instructions protection
1. SAFETY
1.1. ELECTRICAL SAFETY
WARNING! It is the user's responsibility to check the following:
‰
Check all electrical equipment and appliances to ensure that they are safe before using. Inspect power supply leads, plugs and all
electrical connections for wear and damage. Sealey recommend that an RCD (Residual Current Device) is used with all electrical
products. You may obtain an RCD by contacting your local Sealey stockist.
If the product is used in the course of business duties, it must be maintained in a safe condition and routinely PAT (Portable
Appliance Test) tested.
Electrical safety information, it is important that the following information is read and understood.
1.1.1. Ensure that the insulation on all cables and on the appliance is safe before connecting it to the power supply.
1.1.2. Regularly inspect power supply cables and plugs for wear or damage and check all connections to ensure that they are secure.
1.1.3. Important: Ensure that the voltage rating on the appliance suits the power supply to be used and that the plug is fitted with the
correct fuse - see fuse rating in these instructions.
DO NOT pull or carry the appliance by the power cable.
8
DO NOT pull the plug from the socket by the cable. Remove the plug from the socket by
8
maintaining a firm grip on the plug.
DO NOT use worn or damaged cables, plugs or connectors. Ensure that any faulty item is
8
repaired or replaced immediately by a qualified electrician.
1.1.4. This product is fitted with a BS1363/A 13 Amp 3 pin plug.
If the cable or plug is damaged during use, switch the electricity supply and remove from use.
Replace a damaged plug with a BS1363/A 13 Amp 3 pin plug. If in doubt contact a qualified
electrician.
Class II products are wired with live (brown) and neutral (blue) only are marked with the
Class II symbol;
A) Connect the BROWN live wire to the live terminal 'L'.
B) Connect the BLUE neutral wire to the neutral terminal 'N'.
C) After wiring, check that there are no bare wires and ensure that all wires have been correctly
connected.
Ensure that the cable outer sheath extends inside the cable restraint and that the restraint is tight.
DO NOT connect either wire to the earth terminal.
8
Sealey recommend that repairs are carried out by a qualified electrician.
1.2. BATTERY SAFETY (Battery CP1200BP / Charger CP1200MC not supplied)
Charge battery prior to first use. The battery pack will have been shipped in a low charge state.
9
Use only the charger provided to charge the Ratchet Wrench battery.
9
DO NOT charge battery when room temperature is below 50°F (10°C) or above 104°F (40°C).
8
DO NOT attempt recharging the battery by means of a generator or a DC power source.
8
DO NOT short-circuit the battery by linking both terminals with conductive materials.
8
DO NOT store the battery (or Ratchet Wrench) in locations where the temperature may exceed 104°F (40°C).
8
▲ DANGER! DO NOT attempt to dismantle the battery pack. For safety and environmental reasons DO NOT discard in domestic
waste or by burning. ONLY discard or recycle according to local authority regulations.
WARNING! DO NOT allow a leaking battery to contact your person. If you come into contact with battery liquid take the following
‰
immediate action:
a) Skin contact: Wash immediately with soap and water, then wash flesh in either lemon juice or vinegar.
b) Eye contact: Wash with a strong solution of boric acid, and seek immediate medical attention.
1.3. BATTERY CHARGER SAFETY INSTRUCTIONS. (Battery CP1200BP / Charger CP1200MC not supplied)
WARNING: DO NOT use the charger to charge any battery other than that supplied for the Ratchet Wrench. Other types of batteries
‰
may explode.
All mains electrical supply safety features must be followed as described in 1.1. above.
9
Disconnect the charger from the mains power supply when not in use.
9
Important: Check that the voltage marked on the charger is the same as the power supply to be used.
9
DO NOT pull or carry the charger by the power lead, or pull the plug from the mains socket by the power lead.
8
DO NOT use any other type of charger.
8
© Jack Sealey Limited
12V 3/8"SQ DRIVE CORDLESS RATCHET WRENCH
45NM - BODY ONLY
CP1202
MODEL NO:
Wear protective Wear ear
gloves protection
Original Language Version
Charger: Indoor
Use Only
Recommended Fuse
Rating: 3A
CP1202 | Issue 2 (1F) 05/03/20