This manual is subject to revision by the manufacturer. Safety instructions ......04 Smart functions ......30 lG ThinQ application ......30 unpacking ........10 smart Diagnosis ........32 Parts............10 Maintenance ........33 removing Packing Materials ....11 remote Control setup ......13...
Safety instructions READ THESE INSTRUCTIONS CAREFULLY This guide contains many important safety messages. always read and obey all safety messages. This is the safety alert symbol. It alerts you to safety messages that inform you of hazards that can kill or hurt you or others, or cause damage to the product. all safety messages will be preceded by the safety alert symbol and the hazard signal word warnInG or CauTIOn.
Page 5
• Do not install the product in an area exposed to direct sunlight or near heat-generating equipment. • Do not install the product in a place where combustible gas may leak or industrial oil or metallic particulates are present. POWeR •...
Page 6
• If you detect any abnormal noise, odor or smoke, unplug the product immediately and contact an lG electronics service center. • Only an authorized repair person from lG electronics service center should disassemble, repair, or modify the product. • Do not use or store fire, combustibles (ether, benzene, alcohol, drugs, propane, butane, combustible spray, insecticide, air freshener, cosmetics etc.) or flammable materials (candles,...
Page 7
• Be careful not to allow any part of your body to be pinched when you detach and re-attach parts of the product. • unplug the product when not in use for a long time. • Do not install and use broken parts. •...
Page 8
Caution To reduce the risk of fire, electric shock, or personal injury when using the product, follow basic safety precautions, including the following: iNSTALLATiON • Do not tilt the product to pull or push it while transporting. • Do not install the product in transportation equipment (vehicle/ vessel etc.).
Page 9
• Do not operate the product with wet hands. • Do not let the moisture from the humidifier directly touch the product. • Do not use the product while it is not in upright position. • Do not use the product near objects vulnerable to heat. •...
unpacking Parts Air Purifier Owner’s Manual remote Control / Owner’s Manual Battery (Cr2025, 1 unit) • The appearance or components of the product may differ depending on the model. • The shape of the power plug differs depending on the country.
Removing Packing remove the support located at the fi lter inlet. Materials • Upper fi lter inlet: 1 support unpack the product and remove any packing • Lower fi lter inlet: 1 support tape or protective vinyl before using the product.
Page 12
Insert the fi xing parts at the bottom of the cover into the holes at the bottom of the product before you close the cover. remove the protective vinyl from the fi lter at the lower part of the product in the same way.
Remote Control Setup Warning • a button/coin-shaped battery is used in the with the backside of the remote remote control of the product. controller facing up, remove the battery tray from the remote control. • Do not swallow the battery. It may cause injury, including damage to the internal organs or death.
installation Transporting or Moving the installing the Product Product Caution Install the product on a strong level Caution surface. Installing the product on a weak Transport the product in a well-secured or tilted surface may cause noise and and upright position. Impacts may cause vibration or tipping, resulting in injury.
Operation Product Overview front View Clean booster upper part of the air purifier Lower part of the air purifier upper air outlet/Clean booster Lower air inlet (bottom cover) • It discharges purified air through • Air goes into the lower part of the purifier the upper filter.
Page 16
Back View Smart Diagnosis Part Smell (Gas) Sensor In the event of a malfunction or failure, It detects a smell (gas). you can use the smart Diagnosis option to check the product condition. filter (see Smart functions.) It removes allergic materials, yellow dust/ultra-fine dust, possible sources of sick house syndrome, smog and PM 1.0 (super ultra-fine dust)
Page 17
filter System Total Harmful Gas Care filter Caution It removes harmful smells (gas) that • The Total Harmful Gas Care Filter and are generated in everyday life such Total allergen Collection Care Filter are as bathroom smell, cigarette smoke assembled together. Do not try to detach (smell) and food smell.
Page 18
Control Panel Start/Stop Button Booster Speed Button You can start or stop the operation. It allows you to adjust the wind strength of the clean booster. Mode Button • Press and hold it for 3 seconds or more to turn on or off the ionizer. use it to set the operation mode.
Page 19
Displays speed and booster speed It turns on when the 'On/Off Speed: Displays the air purifier's reservation' is set in the lG ThinQ wind strength. application. Booster speed: Displays the It turns on when the control panel is clean booster's wind strength.
Page 20
Remote Control Caution • Do not press multiple buttons at the same time. It may cause the product to stop operating or malfunction. • Do not kick or step on the remote control. It may result in damage. • Do not use it where there is too much water or moisture.
(ready) on the status panel. You can specify the sensor stabilization time in the 'air Quality sensor Operation Time' option in the lG ThinQ application. – 'always On': The sensor stabilization turns on only once at the beginning. – 'Only During Operation': The sensor stabilization turns on every time you start/stop the operation.
using Booster Mode using Dual Mode The clean booster cleans the air and quickly It uses both the upper part and lower part of sends it to a long distances to circulate the the purifier simultaneously to quickly clean indoor air. the indoor air.
using Single Mode Adjusting the fan Speed It cleans the indoor air using the lower part of You can adjust the wind amount of the the purifier. purifier. Press the Mode button to choose Single Press the Speed button during the operation. mode.
Adjusting the Clean Rotating the Clean Booster Booster fan Speed The clean booster rotates left and right. while in Booster mode, press the Swing You can adjust the wind amount of the clean button. booster. while in Booster mode, press the Booster Speed button.
Checking the Air Quality You can check the cleanliness of the indoor air by looking at the light lamp and the status panel. understanding the Overall Air Quality The overall air quality is calculated based on the dust and smell (gas) concentrations and is categorized into 4 levels including green, yellow, orange or red depending on the contamination of the air.
Page 26
Checking Air Quality on the Sta- The above picture displays PM10/PM2.5/ PM1.0, meaning that the concentration of tus Panel super ultra-fine dust is higher than those of fine dust and ultra-fine dust. You may check the overall air quality, dust concentration, and smell concentration on while the color of the dust particle size the status panel.
Page 27
PM2.5 density and is • The fine dust density could be affected based on lG electronics standards. by cooking or using humidifiers, sprays or • The PM10 and PM2.5 densities displayed other products which generate steam or by the product could differ from the ePa fine particles.
using the Air ionizer Setting the Sleep Timer To generate ions to remove various bacteria You can set the product to stop automatically from the air. after running for the duration you set. Press the Booster Speed button for more Press the Sleep Timer button during the than 3 seconds while operating.
Locking the Control Panel Buttons You can lock the buttons on the Control Panel to prevent the product from operating due to unforeseen reasons, such as a child manipulating the buttons. Press the Sleep Timer button for at least 3 seconds during the operation.
• lG ThinQ is not responsible for any • Functions may vary by model. network connection problems or any faults, malfunctions, or errors caused by network Before using LG ThinQ connection.
Page 31
This offer is valid to anyone in receipt of this information. Installing the LG ThinQ Application Search for the LG ThinQ application from the Google Play Store or Apple App Store on a smartphone. Follow instructions to download and install the application.
Fi equipped appliance, it can transmit troubleshooting data to a smartphone using the LG ThinQ application. after the data transfer is complete, • launch the LG ThinQ application and the diagnosis will be displayed in the select the Smart Diagnosis feature in the application.
• How to distinguish between the front the sensor regardless of the cleaning and back of the product: There is an lG frequency (2 months) of the PM 1.0 logo on the front, while 'PM 1.0 & Gas sensor.
wipe the exterior with soft cloth. Caution • Do not disassemble the clean booster arbitrarily. • If the clean booster cover comes apart, secure it by aligning the 3 hooks with the slots before you use the product. • Do not unscrew the 2 screws fixing the Caution clean booster grille on the back while the product is running.
Cleaning the filter Replacing the filter separate the cover from the product. remove the cover and replace the filter. • For more information on how to remove and mount the cover, • For more information on how to please see Removing Packing remove the cover and replace Materials.
Cleaning the Dust Sensor Disabling a Lower filter Replacement Alert PM 1.0 (super ultra-fi ne dust) sensor detects the fi ne dust as well as coarse Press and hold the indicator and Sleep dust. Therefore, you need to clean its lens Timer buttons simultaneously for 3 regularly.
Close the sensor cover. Turn off the power and unplug it from the electrical outlet. • wind the power cord around the bottom of the product. Note The shape of the power plug differs depending on the country. Note Package the product to prevent Do not wipe the sensor with material other the dust or foreign substance from than water.
Before Calling for Service If a failure occurs in the product, check the following before contacting the service Center. Symptom Cause Solution The product does not is the power plug • Plug it into the outlet properly. operate. unplugged from the outlet? Did dust accumulate in •...
Page 39
Symptom Cause Solution • If the amount of the smell is more than the capacity of the product, the display may not Doesn’t the color change change. even if it is moved to a The Light lamp • Clean the sensor area. clean room? continues to stay •...
Page 40
Symptom Cause Solution • The Ministry of environment guide shows the average The overall air quality is the guide from the value over a certain period of is different from that Ministry of environment time, but the overall air quality of the Ministry of different from the product displayed on the product is...
Page 41
Are you looking at the are different between same dust particle? • The difference in the values the product and the could be caused by the LG ThinQ app. difference in update time between the lG ThinQ app and the product.
The external appearance and dimensions of the product are subject to change without prior notice. Model as95GD series Power aC 220–240 V 50 / 60 Hz when the clean booster is not running: 373 mm x 1,073 mm x 373 mm...