1.1 This Functional Specification defines communication functions for LV-7290/LV-7295/LV-7390 /LV-8225/LV-7391/LV-7296. 1.2 Compatible to Firmware Ver. 1.x of the projector. 1.3 Most commands can be used to control projector remotely from PC by RS-232C. Therefore, the commands are defined as Expand Serial Commands. Serial Interface Specification 2.1 Transfer Specification...
Do not issue any command. 4. Name Definition Data from a controller to a projector is represented as COMMAND, and data from a projector to a controller for the incoming command is represented as RESPONSE. [CR] : Carriage Return Code Command ends with cartridge return code.
Set time when Filter warning OSD is displayed Reset Filter used time Set the value to Factory Default Item Behave the same as corresponding key of projector top panel Switch ON/OFF of each Menu. Switch ON/OFF of Power. Set Freeze function.
Get the information for Lamp replacement time Get lamp total running time Get corresponding lamp use time Get Lamp Mode status Get lamp lighting status Get projector total running time Get lamp number Item Get Volume value Get Sound Mute setting status...
Get the information for Filter replacement time Get time when Filter warning OSD is displayed Item Get setting status of Projector behavior Get Signal Status if there is a signal or not Get setting status of Blank Get setting status of Freeze...
7. Error Code Table Error Code Note) These error codes are applied to Expand Command, not to Basic Command Contents -When the received data cannot be decoded -Parameter determination error (digit number error, including invalid value, etc.) The function is not available in the selected Mode Selected value is out of range (Not reflected) Command mismatched to Hardware (command for Optional function which is not installed)
When the projector receives the following functional execution commands, OSD menu is closed except for pop-up menu 2) When Eco mode is selected in Standby mode of Setting menu and projector is in Standby, Functional Execution Commands are invalid. Available Functional Execution Command...
"DN” ----------------------- Current Brightness setting value – 1 Set Brightness value of user control Projector does not save the value set with this command so that it resets when Details projector turning into Standby status or ALL is OFF. (The value is held in Suspend mode.) This command is available in normal Power ON status.
“OFF” ”----------------Set Auto iris to Off Set Auto iris. Projector does not save the value set with this command so that it resets when Details projector turning into Standby status or ALL is OFF. (The value is held in Suspend mode.)
“DN” ------------------- Current Color value set by White Balance%1 - 1 Set Color value set by White Balance%1 of user control Projector does not save the value set with this command so that it resets when Details projector turning into Standby status or ALL is OFF. (The value is held in Suspend mode.)
L2 is more effective in reducing noise than L1, however, L2 can have a blur in moving image Details Projector does not save the value set with this command so that it resets when projector turning into Standby status or ALL is OFF. (The value is held in Suspend mode.) This command is available in normal Power ON status.
8.4.13 CF_COLBOARD Command Command “CF_COLBOARD_%1”[CR] “RED” --------------Select Red “BLUE” ------------ Select Blue “YELLOW” ------- Select Yellow “GREEN” --------- Select Green Select Color of Colorboard mode. Image mode is automatically switched to Colorboard mode by receiving this command. Details The value set by this command is stored in EEPROM and its setting is effective even after ALL is OFF.
“DN” -------------------------- Current Fine Sync setting value - 1 Set Fine Sync value of PC signal Projector does not save the value set with this command so that it resets when Details projector turning into Standby status or ALL is OFF.
“DN” -------------- Current Horizontal Position setting value - 1 Set Horizontal Position value of PC signal. Projector does not save the value set with this command so that it resets when Details projector turning into Standby status or ALL is OFF.
“DN” -------------- Current Display Line setting value – 1 Set Display Line value of PC signal Projector does not save the value set with this command so that it resets when Details projector turning into Standby status or ALL is OFF.
Select Input The same operation as “INPUT” button of the projector and Remote Control. This command is available in normal Power ON status. Details Projector returns “101” by selecting Computer 2 while Monitor out is selected in Terminal menu. Acceptable Response Unacceptable 8.6.2...
Select Computer 2 input and source specified by %1 at the same time. This command is available in normal Power ON status. Details Projector returns “101” by selecting Computer 2 while Monitor out is selected in Terminal menu. Acceptable Response Unacceptable 8.6.5...
Select Input specified by %1 and also Source specified by %2 at once This command is available in normal Power ON status. Details Projector returns “101” by selecting Computer 2 while Monitor out is selected in Terminal menu. Acceptable Response Unacceptable “000”[CR]...
Computer Input is Video Select System of currently selected Input When Input specified by %1 is inappropriate for selected Input, the projector returns “101”[CR] and the command is not executed This command is available in normal Power ON status. Details Note1) “NTSC”...
Common Select Aspect mode (image size on screen). When Input specified by %1 is inappropriate for selected Input, the projector returns “101” [CR] and the command is not executed. “DZOOM UP” and “DZOOM DN” start effecting from the first command.
This command is available in normal Power ON status. Note1) When Aspect setting is not in Custom mode, projector changes image Details mode into Custom by receiving this command. Note2) When there is no signal detected, projector returns 101 and the command does not execute. Acceptable Response Unacceptable 8.7.4...
This command is available in normal Power ON status. Details Note1) When Aspect setting is not in Custom mode, projector changes image mode into Custom by receiving this command. Note2) When there is no signal detected, projector returns 101 and the command does not execute. Acceptable Response Unacceptable 8.7.6...
8.7.7 CF_KEYSTONE Command Command “CF_KEYSTONE_%1”[CR] “UP” ------------- Correct Keystone distortion to reduce upper part of image “FUP” ----------- Correct Keystone distortion to reduce upper part by 2steps “DN” ------------- Correct Keystone distortion to reduce lower part of image “FDN” ----------- Correct Keystone distortion to reduce lower part by 2steps “RST”...
8.8 Lamp Command 8.8.1 CF_LAMPH Command Command “CF_LAMPH_%1”[CR] “RST” Reset total lamp running time Details This command is available in normal Power ON status. Acceptable Response Unacceptable 8.8.2 CF_LAMPMODE Command Command “CF_LAMPMODE_%1”[CR] “HIGH” ------------ Set lamp to High mode status “NORMAL”...
“UP” --------------------------------- Current Volume setting value +1 “DN” --------------------------------- Current Volume setting value -1 Control Volume value The same operation of Volume Up/Down as projector and RC, and directly select Volume setting value. When setting Volume value, the Sound Mute ON status is Details canceled just like RC operation.
8.9.5 CF_STANDBYMICOUT Command Command “CF_STANDBYMICOUT_%1”[CR] “ON” ----------------------------- Set STANDBY MIC OUT to ON “OFF” ---------------------------- Set STANDBY MIC OUT to OFF Control Standby MIC out ON/OFF Details This command is available in normal Power ON status. Acceptable Response Unacceptable “000”[CR] “Error Code”[CR]...
This command is available in normal Power ON status. Note) It is unable to set Keystone, Auto PC and Auto input to OFF at once. e.g. If projector receives Auto input OFF command while Auto PC and Keystone are OFF, it returns error code “101”..
8.10.7 CF_BACKGND Command Command “CF_BACKGND_%1” [CR] “BLUE” -------------------- Select Blue Back “USER” ------------------- Select User “BLACK” ------------------ Select Black Back “UP” ----------------------- The same operation as pressing Up key or Left key “DN” ----------------------- The same operation as pressing Down key or Right key Set Screen status for no signal.(Available only in the normal Power ON status) The status set by this command is stored in EEPROM and the setting remains even after the power is turned to ALL OFF status.
Note) Receiving correct LOGO PIN CODE while LOGO LOCK is in operation enables to change LOGO setting, but it does not release LOGO LOCK. (LOGO LOCK continues.) Projector returns Error Code “101” by receiving USER in %2 when capture has not operated. Acceptable...
8.10.11 CF_P-MANE Command Command “CF_P-MANE_%1”[CR] “OFF” ----------------------------- Set Power management mode to OFF “READY” ------------------------- Set Power management mode to Standby “SHUTDOWN” ----------------- Set Power management mode to Exit. “UP” ----------------------- The same operation as pressing Up key or Left key “DN”...
8.10.15 CF_PTIMEMODE Command Command “CF_PTIMEMODE_%1”[CR] “COUNTUP” ---------------- Select Count up “COUNTDN” ---------------- Select Countdown Set operation mode of P-timer. The status set by this command is stored in EEPROM and its setting is effective Details after ALL is OFF This command is available in normal Power ON status. Acceptable Response Unacceptable...
Response Unacceptable 8.10.21 CF_KEYDIS Command Command “CF_KEYDIS_%1”[CR] “NONE” ----------------------- RC & Projector keys are valid (All are valid) “RC” ---------------------------- RC keys are invalid “KEY” -------------------------- Projector keys are invalid Disable RC/Projector keys Details This command is available in normal Power ON status.
8.10.22 CF_PJPINCODE Command Command “CF_PJPINCODE_%1”[CR] “0000” – “9999” ---------Set PJ PIN CODE directly Set PJ PIN CODE to release PJ LOCK. PIN CODE cannot be changed by this command. -When PJ LOCK is in operation PIN CODE is correct ------------------------- Command is valid (Acceptable) PIN CODE is incorrect ----------------------- Command is invalid(Error Code”102”) PIN CODE is out of %1 range ------------- Command is invalid (Error Code “? “) Details...
8.10.25 CF_DELAYCTRL Command Command “CF_DELAYCTRL_%1”[CR] “ON” --------------------------- Set Video delay control On “OFF” -------------------------- Set Video delay control Off Set Video delay control. Details The status set by this command is stored in EEPROM and its setting is effective even after ALL is OFF. This command is available in normal Power ON status. Acceptable Response Unacceptable...
“OFF” ---------- Power OFF Projector Note1) Countdown can be terminated by sending this command. Note2) Projector returns error code due to unable of command execution depends on its condition. Note3) Although projector returns “OK”, operation may not be proceeding properly.
“UP” --------------- The same operation as pressing Up key or Left key “DN” --------------- The same operation as pressing Down key or Right key Set/Cancel Freeze setting. Although projector returns “000”, receiving another Freeze command does not Details release Freeze operation.
PC ← PJ: “000_1344” [CR] 9.3 Operation Condition 1) Basically Status Read Commands should be always operated. 2) When Eco mode is selected in Standby mode of the Setting menu and projector is in Standby, Status Read Commands are invalid.
9.4 Image Status Read Command 9.4.1 CR_BRIGHT Command Command “CR_BRIGHT”[CR] Details Get Brightness value of user control Acceptable Response Unacceptable 9.4.2 CR_CONT Command Command “CR_CONT”[CR] Details Get Contrast value of user control Acceptable Response Unacceptable 9.4.3 CR_COLOR Command Command “CR_COLOR”[CR] Details Get Color value of user control Acceptable...
9.4.6 CR_SHARP Command Command “CR_SHARP”[CR] Details Get Sharpness value of user control Acceptable Response Unacceptable 9.4.7 CR_GAMMA Command Command "CR_GAMMA”[CR] Details Get Gamma value of user control Acceptable Response Unacceptable 9.4.8 CR_WBAL – R Command Command "CR_WBAL-R”[CR] Details Get White Balance Red value of user control Acceptable Response Unacceptable...
9.4.11 CR_COLTEMP Command Command "CR_COLTEMP”[CR] Details Get Color Temp. setting value Acceptable Response Unacceptable 9.4.12 CR_NZRED Command Command “CR_NZRED”[CR] Details Get setting status of Noise Reduction Acceptable Response Unacceptable 9.4.13 CR_PROGV Command Command “CR_PROGV”[CR] Details Get setting status of Progressive scan Acceptable Response Unacceptable...
9.5 PC Adjust Status Read Command 9.5.1 CR_FSYNC Command Command "CR_FSYNC”[CR] Details Get Fine Sync value Acceptable Response Unacceptable 9.5.2 CR_TDOTS Command Command “CR_TDOTS”[CR] Details Get Total Dots value Acceptable Response Unacceptable 9.5.3 CR_CLAMP Command Command “CR_CLAMP”[CR] Details Get Clamp value Acceptable Response Unacceptable...
9.5.6 CR_DDOTS Command Command “CR_DDOTS”[CR] Details Get Display Dots value Acceptable Response Unacceptable 9.5.7 CR_DLINE Command Command “CR_DLINE”[CR] Details Get Display Line value Acceptable Response Unacceptable 9.5.8 CR_PCSTORE Command Command “CR_PCSTORE”[CR] Get Free/Stored status of MODE1 - MODE5 for PC Adjust. Details Each data consists of 10 bytes.
9.6 Video Status Read Command 9.6.1 CR_SERSYS Command Command “CR_SERSYS”[CR] Get currently selected signal Details Returns auto-detected signal in Auto mode Only available for Video input. (N/A when Input is computer) Acceptable Response Unacceptable “000_%a”[CR] “1080I60” -------------- 1080i 60Hz “1080I50” -------------- 1080i 50Hz “1035I”.
“480i” -------------- 480i is selected “MODE1” ------- Mode1 is selected : “MODE10” -------------- Mode10 is selected When there is no signal, projector returns error code”101” [CR] “AUTO” ----------- Auto is selected “1080i” ------------1080i is selected “1035i” ------------ 1035i is selected “720p”...
: : “575I” ------------ 575i is selectable “480I” ------------ 480i is selectable Projector does not return Error Code “101” even if there is no signal. -When Input is Video, S-Video Returns all the System titles on Menu including Auto “AUTO” ---------Auto is selectable “PAL”...
“WIDE” -------------------- 16:9 mode is selected “ZOOM” -------------------- Zoom mode is selected “TRUE” -------------------- True mode is selected When the screen is set to D.Zoom, projector returns the previous status (NORMAL ) “CUSTOM” ---------------- Custom mode is selected “NORMAL” --------------- Normal mode is selected “FULL”...
9.8.5 CR_HPOS Command Command “CR_HPOS”[CR] Details Get setting status of Horizontal Position Store Mode Acceptable Response Unacceptable 9.8.6 CR_ KYSTNMODE Command Command “CR_KYSTNMODE”[CR] Details Get setting status of Keystone Store Mode Acceptable Response Unacceptable 9.8.7 CR_CEIL Command Command “CR_CEIL” [CR] Details Get setting status of Ceiling Acceptable...
“1N” -------------------------- Within lamp replacement time “1” means the number of lamps. (1 lamp model→ “1”) “Y”/”N” means if it has reached its replacement time or not. e.g. “1Y” -----------projector is 1 lamp model and Lamp is over its replacement time “Error Code”[CR] “000_%1”[CR] “00000”~“99999”...
Command “CR_LAMPSTS”[CR] Details Get Lighting status of lamp Acceptable Response Unacceptable 9.9.6 CR_PROJH Command Command “CR_PROJH”[CR] Details Get total running time of Projector by hour (h) Acceptable Response Unacceptable 9.9.7 CR_HMLAMP Command Command “CR_HMLAMP”[CR] Details Get lamp number. Acceptable Response Unacceptable “000_%1”[CR]...
9.10 Sound Status Read Command 9.10.1 CR_VOLUME Command Command “CR_VOLUME”[CR] Details Get Volume value of user control Acceptable Response Unacceptable 9.10.2 CR_MUTE Command Command “CR_MUTE”[CR] Details Get sound mute setting status Acceptable Response Unacceptable 9.10.3 CR_MIC Command Command “CR_MIC”[CR] Details Get setting status of MIC Acceptable Response...
9.11 Setting Status Read Command 9.11.1 CR_LANG Command Command “CR_LANG”[CR] Details Get selected language Acceptable Response Unacceptable 9.11.2 CR_INPUTSEARCH Command Command “CR_INPUTSEARCH”[CR] Details Get setting status of Auto input Acceptable Response Unacceptable 9.11.3 CR_AUTOSETUPPCADJ Command Command “CR_AUTOSETUPPCADJ” [CR] Details Get Auto PC setting status in Auto setup Acceptable Response Unacceptable...
9.11.4 CR_AUTOSETUPKEYSTONE Command Command “CR_AUTOSETUPKEYSTONE” [CR] Details Get Keystone setting status in Auto setup Acceptable Response Unacceptable 9.11.5 CR_BACKGND Command Command “CR_BACKGND” [CR] Details Get setting status of Screen for no signal Acceptable Response Unacceptable 9.11.6 CR_DISP Command Command “CR_DISP”[CR] Details Get setting status of Display Acceptable...
9.11.9 CR_P-MANE Command Command “CR_P-MANE”[CR] Details Get Power management mode setting status Acceptable Response Unacceptable 9.11.10 CR_P-MANETIME Command Command “CR_P-MANETIME”[CR] Details Get time to start Power management mode Acceptable Response Unacceptable 9.11.11 CR_ON-STA Command Command “CR_ON-STA”[CR] Details Get Direct power on setting status Acceptable Response Unacceptable...
9.11.14 CR_PTIMER Command Command “CR_PTIMER”[CR] Details Get current status of P-timer Acceptable Response Unacceptable 9.11.15 CR_PTIME Command Command “CR_PTIME”[CR] Details Get setting time for Countdown in P-timer function Acceptable Response Unacceptable 9.11.16 CR_CCAPTIONDISP Command Command “CR_CCAPTIONDISP”[CR] Details Get selected channel of Closed caption Acceptable Response %a...
Get Security Mode setting status Acceptable Response Unacceptable 9.11.20 CR_KEYDIS Command Command “CR_KEYDIS”(CR) Details Get disability status of RC/Projector keys (valid or invalid) Acceptable Response Unacceptable 9.11.21 CR_PJLOCKNOW Command Command “CR_PJLOCKNOW” [CR] Details Get if PJ lock is actually in operation...
9.11.24 CR_FANCONTROL Command Command “CR_FANCONTROL”[CR] Details Get selected Fan control setting status Acceptable Response Unacceptable 9.11.25 CR_DELAYCTRL Command Command “CR_DELAYCTRL”[CR] Details Get setting status of Video delay control Acceptable Response Unacceptable 9.11.26 CR_FILH Command Command “CR_FILH”[CR] Details Get Filter used time Acceptable Response Unacceptable...
9.12 Other Status Read Command 9.12.1 CR_STATUS Command Command “CR_STATUS”(CR) Get status of Projector behavior. Details This command affects the same as ”CR0” of Basic Serial command, but this has an error code. Acceptable Response Unacceptable 9.12.2 CR_SIGNAL Command Command “CR_SIGNAL”(CR)
9.12.5 CR_TEMPWARN Command Command “CR_TEMPWARN”[CR] Get the temperature inside a projector and its condition if it is abnormal temperature or close to abnormal temperature Details If there are several sensors installed, it is possible to get information from all the sensors at once.
2 detects 35.2 degrees which means safety, and sensor 3 is 38 degrees which is close to abnormal temp. In case projector cannot return its data due to some hard ware failure, the last character becomes “E” such as “_00.0E”.
When the temperature is safe, all data are represented as “□000S”. When the projector is reset, “□000S” is set, and every time abnormal temperature occurs, it renews the data and returns it. In short, it only returns the renewed data of the latest abnormal temperature and the previous data is deleted.