Advertisement
Trim Kit Center Trim Support
4.
With the refrigerator still on its
5
/
"
back, use a
nut driver to
16
remove two 4H bolts and fasten
the 10H L-Bar (Fig. 8).
Note: The short flange on L-Bar
should be facing upward toward
the top of the refrigerator.
5.
Stand both units upright.
CAUTION
The cabinet is heavy. Two people are recommended to lift or move the cabinet..
Pairing Kit Installation
Before cleaning your appliance, turn off power to your appliance by
unplugging the power cord from the electrical outlet. Wipe down both
sides of the refrigerator and the freezer.
NOTE
Never use CHLORIDE to clean stainless steel. Clean stainless-steel front
and handles with non-abrasive soapy water and a dishcloth. Rinse with
clean water and a soft cloth. Wipe stubborn spots with an ammonia-
soaked paper towel, and rinse. Use a non-abrasive stainless-steel
Ready
cleaner, such as Frigidaire
found on Frigidaire.com. Always follow the manufacturer's instruction.
NOTE
Always, clean, wipe and dry with the grain to prevent scratching.
Wash the rest of the cabinet with warm water and mild liquid
detergent. Rinse well and wipe dry with a clean soft cloth.
Note: Use gloves for the next step.
6.
Peel off the paper backing from the first heater.
7.
Adhere the first heater to the lower right side of the left-side unit (0.5"
from the bottom and 0.5" from the back wall) so the harnesses come
out at the top.
NOTE: Make sure you adhere
the heater completely with no
air pockets (Fig. 9A).
8.
Peel off the paper backing
from the second heater.
9.
Adhere the second heater to
the upper left side of the right-
side unit (0.5" from the top
and 0.5" from the back wall)
so the harnesses come out at
the bottom.
NOTE: Make sure you adhere
the heater completely with no
air pockets (Fig. 9B). For better
adhesion remove the yellow label
on the side of the cabinet.
NOTE: Before removing the paper
backing, align the heaters to
ensure the wires exit toward the
center and rear of refrigerator/
freezer (as shown in Fig 9).
Fig. 8
Clean™ Stainless Steel Cleaner
0.5"
0.5"
0.5"
A
Fig. 9
NOTE: For the best results, please
use the configurations of the
heaters mentioned (Freezer- top
right side and Refrigerator bottom
left side).
Avoid:
Both heaters on the Freezer
Both heaters on the Refrigerator
Both heaters on the top
Both heaters on the bottom
Both heaters in the center
10.
Plug in the connector of the
two Heaters A into the Power
Supply C (Fig. 10).
NOTE: Confirm the power supply
fits into the cutout when placed
on top of the unit. Also confirm the
power supply reaches the power
outlet when placed on top of the
unit (Fig. 11A). The extra wire length
is provided to accommodate
receptacle location.
11.
Apply the 2 strips of double-
sided tape to the power
supply and adhere the power
supply on top of the unit
(Fig. 11B).
IMPORTANT
Make sure there are two separate outlets for the freezer and the refrigerator.
12.
If the power supply cannot
be placed on top of the unit,
adhere it vertically on the
back wall of the unit and
make sure the connection of
the 3-prong connector to the
power supply is facing down
(Fig. 12).
NOTE: You cannot feel the
heater temperature.
B
©2021 Electrolux Home Products, Inc.
INSTRUCTION SHEET
C
A
Fig. 10
Fig. 11
Fig. 12
Instruction Sheet A00343905
B
B
A
7.23.21
Advertisement
