Related Manuals for GE Druck DPI 150
Summary of Contents for GE Druck DPI 150
- Page 1 99 Washington Street Melrose, MA 02176 Fax 781-665-0780 GE Infrastructure TestEquipmentDepot.com Sensing Druck DPI 150 Pressure Indicator User manual - K344 »...
- Page 3 For technical advice contact the manufacturer or subsidiary. Supervisor Security for the Druck DPI 150 GE strongly advise protection of the set-up menus in this equipment. Unauthorised access to the supervisor and calibration menus can result in degraded performance, incorrect settings and inaccuracies. The factory set...
-
Page 4: Table Of Contents
Druck DPI 150 User Manual ABBREVIATIONS The following abbreviations are used in this publication. Note: Abbreviations are the same in the singular and plural. absolute pounds British Standard Pipe (thread) metre calibrated airspeed mbar millibar °C degrees Celsius millimetre const... -
Page 5: Introduction
Druck DPI 150 User Manual Introduction The Druck DPI 150 high accuracy, single-range pressure indicator uses the Druck IDOS sensor to produce pressure readings in units of pressure measurement and aeronautical units. The instrument is contained in a moulded plastic case with integral rubber feet for workbench surface use. -
Page 6: Installation
Druck DPI 150 User Manual Environmental Temperature Operating ............5° to 50°C (41° to 122°F) Calibrated................23°C (74°F) Storage............-20° to 60°C (-4° to 140°F) Humidity ........complies with Def. Stan. 66-31 8.6 cat 3 Vibration ........complies with Def. Stan. 66-31 8.4 cat 3 Shock ........mechanical shock conforms to EN 61010... -
Page 7: Connections
Druck DPI 150 User Manual Connections Note: Switch off the power supply before connecting or disconnecting the instrument. Isolate the pneumatic supply pressures and depressurise the pipes before connecting or disconnecting the instrument. Use an appropriate sealing method for all pressure connections. -
Page 8: Analogue Output Option
Druck DPI 150 User Manual Using other power adaptors Responsibility of the User A power adaptor, not supplied with the instrument, must comply with the EN61010 SELV safety requirements of Voltage AC or DC Power Polarity 11 to 26 10VA... -
Page 9: Bench Stand
Druck DPI 150 User Manual Procedure To fit this option requires a panel cut-out of the dimensions shown in Remove the rubber inserts in the feet of the instrument. Unscrew and remove two 45mm screws (2) attaching two feet on one side of the instrument casing. -
Page 10: Operation
Druck DPI 150 User Manual Operation Key to 1 esc key 6 soft key right 2 menu OK key 7 soft key left 3 zero key 8 display 4 hold key 9 up or increase key 5 down or decrease key... -
Page 11: Select Mode Menu
Druck DPI 150 User Manual Select mode menu K344 Issue No. 2... -
Page 12: Indicator Mode
Druck DPI 150 User Manual Indicator mode K344 Issue No. 2... - Page 13 Druck DPI 150 User Manual Indicator mode continued K344 Issue No. 2...
-
Page 14: User Set-Up
Druck DPI 150 User Manual User Set-up K344 Issue No. 2... -
Page 15: Pressure Leak Test
Druck DPI 150 User Manual Pressure leak test K344 Issue No. 2 Test Equipment Depot - 800.517.8431 - 99 Washington Street Melrose, MA 02176 FAX 781.665.0780 - TestEquipmentDepot.com... -
Page 16: Airspeed Leak Test
Druck DPI 150 User Manual Airspeed leak test (must be correctly enabled) K344 Issue No. 2... -
Page 17: Airspeed
Druck DPI 150 User Manual Airspeed (must be correctly enabled) K344 Issue No. 2... -
Page 18: Mach
Druck DPI 150 User Manual Mach (must be correctly enabled) K344 Issue No. 2... -
Page 19: Supervisor Set-Up
Druck DPI 150 User Manual Supervisor Set-up K344 Issue No. 2... - Page 20 Druck DPI 150 User Manual Supervisor set-up (continued) Communications K344 Issue No. 2...
- Page 21 Druck DPI 150 User Manual Supervisor set-up (continued) Analogue output option K344 Issue No. 2...
-
Page 22: Status
Druck DPI 150 User Manual Status K344 Issue No. 2 Test Equipment Depot - 800.517.8431 - 99 Washington Street Melrose, MA 02176 FAX 781.665.0780 - TestEquipmentDepot.com...