Page 1
Original Instruction Manual Important: Read this instruction manual carefully before putting the petrol chain saw into operation and strictly observe the safety regulations! Keep this instruction manual! EA3200S EA3201S EA3202S EA3203S...
Page 1. Delivery inventory Thank you for purchasing a MAKITA product! 2. Symbols Congratulations on choosing a MAKITA chain saw! We are 3. SAFETY PRECAUTIONS Intended use con dent that you will be satis ed with this modern piece of...
1. Delivery inventory (Fig. 1) 1. Chain saw 2. Guide bar 3. Saw chain 4. Chain protection cover 5. Universal wrench 6. Screwdriver for carburetor adjustment 7. Instruction manual (not shown) In case one of the parts listed should not be included in the delivery inventory please consult your sales agent 2.
3. SAFETY PRECAUTIONS 3-1. Intended use Wear adequate noise protection equipment (ear muffs ( , ear plugs, etc. . Octave band analysis may be provided upon request. Power chain saws The safety jacket ( is provided with special signal- This power chain saw may be used only for sawing wood out coloured shoulder straps and is comfortable and easy to of doors.
Before starting the chain saw ensure that you have a safe Always ensure that you have a safe footing. footing. Never saw above your shoulder height (Fig. 12). Put the chain saw into operation only as described in this Never saw while standing on a ladder (Fig. 12). instruction manual (Fig.
1/10 of the Use only original MAKITA spare parts and accessories. trunk diameter. Using spare parts other than original MAKITA parts or The material between both cuts (C serves as a hinge. accessories and guide bar/chain combinations or lengths Never cut it through, otherwise the tree will fall without any which are not approved bring a high risk of accidents.
4. Technical data EA3200S EA3201S EA3202S EA3203S tro e volume Bore tro e 28 2 Ma power at speed W 1 min 1 35 10 000 Ma tor ue at speed m 1 min 1 6 7 000 Idling speed ma engine speed with bar and chain...
5. Denomination of components (Fig. 24) andle 14 Identi cation plate 2 Cover tarter grip ood loc under the hood cap) 16 Combination switch Cho e top) 4 Tubular handle 17 Throttle lever and guard release for chain bra e) afety loc ing button 6 Mu er 19 Rear hand guard...
6a-4. Retightening the saw chain NOTE: It is recommended to use 2 3 chains alternatively (Fig. 33) In order to guarantee uniform wear of the guide bar the bar should be turned over whenever replacing the chain Loosen the nuts (2) about one turn with the universal wrench.
6c. Only for models with quick tensioner on sprocket guard (TLC) 6c-2. Tightening the saw chain (Fig. 46) CAUTION: imultaneously push in hard on the sproc et guard uic Before doing any work on the guide bar or chain, tensioner 2) and turn it cloc wise to screw the sproc et guard always switch o the engine and pull the plug on but do not yet tighten it cap o the spark plug see 7 6 Replacing the spar...
980 008 606 temperatures once fuel has been mi ed it should be used up In case MAKITA high performance two stro e engine oil is not in 6 8 wee s available it is urgently recommended to use a mi ture ratio of...
In case of damage caused by using waste oil or inappropriate The chain oil BI T P sold by MAKITA is made of special chain oil the product guarantee will be null and void...
6-9. Checking the chain lubrication ever wor with the chain saw without su cient chain If the lubrication is su cient you will see a light oil trace lubrication therwise the service life of the chain and guide because oil will be ung o the sawing device Pay attention bar will be reduced Before starting wor chec the oil level in to the direction the wind is blowing and avoid unnecessary the tan and the oil feed...
Caution: If the chain does not stop immediately in this (Fig. 57) test, turn o the engine immediately. Do NOT use the chain saw in this condition! Contact a MAKITA authorized old the front handle rmly with your other hand on the rear service center.
Regular inspection and maintenance are important for increase wear and tear and cause chain bea age your own safety and must be done by a MAKITA service Files and how to work with them center.
CAUTION: 7-3. Cleaning the guide bar Replace damaged air lters immediately. Pieces of cloth or large dirt particles can destroy the CAUTION: Protective gloves must be worn. engine! (Fig. 66) Insert the air lter 6) in the illustrated direction Regularly inspect the bearing surfaces of the guide bar 7) for CAUTION: damage and clean them with a suitable tool Do not insert the air lter upside-down, even after...
Note: or saw models with catalytic converters A3200 spring engages A3201 ) remove the converter along with the upper mu er Install the spring 6) and driver 8) and screw on tight with half screw 7) The screws on the bottom mu er half 14) are now accessible Tension the spring see above) and it is possible to chec them for tightness If they are loose Replacing the starter spring...
The user of the chain saw must not perform maintenance wor which is not described in the instruction manual All such wor must be carried out by a MAKITA service center ection General...
9. Trouble shooting Malfunction System Observation Cause Chain does not run Chain bra e ngine runs Chain bra e actuated ngine does not start or Ignition system Ignition spar Malfunction in fuel supply system only with di culty compression system mechanical malfunction o ignition spar T P switch in position fault or short...
10. Extract from the spare parts list (Fig. 76) EA3200S, EA3201S se only original MAKITA parts or repairs and EA3202S, EA3203S replacement of other parts see your MAKITA service center Spare parts Accessories not delivered with the chain saw) Pos.
Page 45
50:1 MAKITA 50:1 50:1 50:1 1000 5000 10000 6-7. A 30) BI T P MAKITA BI T P Blauer mweltschut - ngel) RA Z 48) BI T P BI T P 980 008 610 980 008 611...