English CORDLESS CONCRETE NAILER DCN890 Congratulations! EC-Declaration of Conformity You have chosen a D WALT tool. Years of experience, thorough Machinery Directive product development and innovation make D WALT one of the most reliable partners for professional power tool users. Technical Data...
Weight English Batteries Chargers/Charge Times (Minutes) Weight DCB107 DCB113 DCB115 DCB118 DCB132 DCB119 Cat # DCB546 18/54 6.0/2.0 1.05 DCB547 18/54 9.0/3.0 1.25 DCB181 0.35 DCB182 0.61 DCB183/B 0.40 DCB184/B 0.62 DCB185 0.35 DCB187 0.48 f ) If operating a power tool in a damp location is instructions may result in electric shock, fire and/or serious injury.
English b ) Do not use the power tool if the switch does not turn Do not point the tool towards yourself or anyone • it on and off. Any power tool that cannot be controlled nearby. Unexpected triggering could discharge a fastener with the switch is dangerous and must be repaired.
English Use the tool only for its intended use. Do not discharge voltage on the rating plate. Also make sure that the voltage of • fasteners into open air or any material too hard for your charger corresponds to that of your mains. the pin to penetrate.
English 3. The completion of charge will be indicated by the red charger cavities. Always unplug the charger from the power supply when there is no battery pack in the cavity. light remaining ON continuously. The battery pack is fully Unplug charger before attempting to clean charged and may be used at this time or left in the charger.
Page 11
English charger within reach of an electrical outlet, and away from a WARNING: Never attempt to open the battery pack for corner or other obstructions which may impede air flow. Use any reason. If battery pack case is cracked or damaged, the back of the charger as a template for the location of the do not insert into charger.
Battery Type 1. The best storage place is one that is cool and dry away The DCN890 operates on a 18 volt battery pack. from direct sunlight and excess heat or cold. For optimum These battery packs may be used: DCB181, DCB182, DCB183,...
English • This product is not intended for use by persons (including Visible radiation. Do not stare into light. children) suffering from diminished physical, sensory or mental abilities; lack of experience, knowledge or skills unless they are supervised by a person responsible for their Length of nails.
Page 14
English Proper Hand Position (Fig. D) To Remove Utility Hook 1. Remove battery pack from tool. WARNING: To reduce the risk of serious personal injury, 2. To switch the tool from right- to left-hand usage simply ALWAYS use proper hand position as shown. remove the screw ...
English WARNING: Always remove battery pack before loading or Speed Setting Application Typical Pin Length unloading pins. Fastening Steel/Wood to Low Strength 19-25 mm CAUTION: Keep fingers clear of pusher latch track to Concrete/Masonry (<4000 psi) prevent injury. Fastening Steel/Wood to High Strength 19-29 mm WARNING: The trigger lock-off should always be engaged Concrete (>4000 psi)
Page 16
English Pin/Fastener Troubleshooting STEEL Pin does not penetrate the surface. Cause: Speed setting too low Properly driven pin Over driven pin Material to hard for pin type CONCRETE Action: Pin does not hold in the concrete. Increase tool speed setting Cause: Pin breaks or bends.
English Stall Release (Fig. I) nOTE: Should pins jam frequently or the driver continually fail to reset, have tool serviced by an authorised D WALT service If the nailer is used in harder material where all available energy centre. in the motor is used to drive a fastener, the tool may stall. Cold Weather Operation The driver will not complete the drive cycle and the jam/stall indicator will flash.
English 4. Push up on the rear of the driver until you hear a click, 20 then push the driver forward while holding it in this position until it passes the upper bumper assembly 22 Cleaning 5. Remove guide rods 21 ...
English TROUBLESHOOTING GUIDE WARNING: To reduce the risk of serious personal injury, turn tool off and disconnect battery pack before making any adjustments or removing/installing attachments or accessories. An accidental start-up can cause injury. SYMPTOM CAUSE Motor does not run with contact Trigger lock in locked position Unlock trigger lock.
Page 20
English SYMPTOM CAUSE Tool operates but does not drive Speed select setting in wrong position. Set speed to appropriate setting. fasteners fully Tool not firmly applied to workpiece Apply adequate force to tool securing it tightly to workpiece. See instruction manual. Material and fastener length If the unit continues to stall (forcing the need to rotate the stall release lever) choose the appropriate material and fastener length that is not...
Page 24
Belgique et WALT - Belgium BVBA Tel: NL 32 15 47 37 63 www.dewalt.be Luxembourg België en Luxemburg Egide Walschaertsstraat 16 Tel: FR 32 15 47 37 64 enduser.BE@SBDinc.com 2800 Mechelen Fax: 32 15 47 37 99 Danmark WALT (Stanley Black&Decker AS)