Summary of Contents for Toro Greensmaster 3150 Series
Page 1
DPA Cutting Unit Greensmaster ® 3150 or 3250-D Series Traction Unit Model No. 04652—Serial No. 316000001 and Up Model No. 04654—Serial No. 316000001 and Up Model No. 04656—Serial No. 316000001 and Up *3397-897* B Register at www.Toro.com. Original Instructions (EN)
Page 2
Whenever you need service, genuine Toro parts, or additional information, contact an Authorized Service Dealer or Toro Customer Service and have the model and serial numbers of your product ready. Figure 1 identifies the location of the model and serial numbers on the product.
Contents Safety Safety ............... 3 This machine has been designed in accordance with General Safety ........... 3 EN ISO 5395:2013 and ANSI B71.1-2012. Safe Operating Practices........3 Safety and Instructional Decals ......4 General Safety Setup ................ 5 Installing the Roller ..........5 This product is capable of amputating hands and Installing the Ball Studs........
• • Wear appropriate clothing, including eye Keep your hands and feet away from the cutting protection; substantial, slip-resistant footwear; units. long pants, and hearing protection. Tie back long • Keep all parts in good working condition and all hair and do not wear loose jewelry. hardware tightened.
Setup Media and Additional Parts Description Qty. Ball stud Mount this to the roller. Operator's Manual Read before installing and operating the cutting unit. Parts catalog Use this to reference part numbers. Installing the Roller Center the roller between the height-of-cut arms. Tighten the roller-mounting screws (Figure The cutting unit is shipped without a front roller.
8). Torque the bolts to 16 to 20 N∙m (12 to 15 ft-lb). 1. Offset lift hook • Optionally for the Greensmaster 3250-D traction units, you can install the chain Link and mounting bracket available from your authorized Toro distributor.
g016515 Figure 8 1. Drive spline 3. Allen head bolts 2. Motor mount On the right end of the cutting unit, apply a light coating of oil to the O-ring and install the counter weight with the bolts previously removed (Figure 9).
8 Blade—30 kg (65 lb), 11 Blade—31 kg (68 lb), 14 Blade—32 kg (71 lb) Attachments/Accessories A selection of Toro approved attachments and accessories is available for use with the machine to enhance and expand its capabilities. Contact your Authorized Service Dealer or Distributor or go to www.Toro.com for a list of all approved attachments and accessories.
Adjusting the edges needed for precision cutting (Refer to the Toro Manual for Sharpening Reel and Bedknife-to-Reel Contact Rotary Mowers, Form No. 09168SL). Important:...
g014404 Figure 15 1. Spacer 3. Roller bracket 2. Sideplate-mounting flange g028838 • Position the spacer below the sideplate-mounting Figure 14 flange when the height-of-cut settings range from Models 03639 and 03641 3 mm to 25 mm (1/8 inch to 1 inch) as shown in Figure 2.
Adjusting the Height of Cut Use the following chart to determine which bedknife is best suited for the desired height of cut. Bedknife Part No. Height-of-Cut Edgemax 115-1880 1.5 to 4.7 mm (0.062 to Micro-cut 0.188 inch) (Standard) g000489 Edgemax 115-1881 3.1 to 12.7 mm (0.125 to Figure 17...
Ideally, take the cutting unit to your authorized Toro distributor for service. Refer to Verify that the height-of-cut setting is correct; the Service Manual for your traction unit for complete repeat this procedure if necessary.
Page 14
Removing the Bedbar Turn the bedbar adjusting screw, counterclockwise, to back the bedknife away from the reel (Figure 21). g020056 Figure 23 1. Bedbar bolt 3. Nylon washer 2. Nut 4. Steel washer Assembling the Bedbar Install the bedbar, positioning the mounting ears between the washers and the bedbar-adjusting g016429 Figure 21...
g034114 g016470 Figure 26 Figure 24 1. Angle-indicator mount 3. Bedknife 1. Spring-tension nut 2. Spring 2. Edge of the magnet mated 4. Angle indicator with the edge of the bedknife Adjust the bedknife to the reel; refer to Adjusting the Bedknife-to-Reel Contact (page Place the angle indicator on the mount as shown Figure...
Installing the Bedknife Remove the rust, scale, and corrosion from the bedbar surface and apply a thin layer of oil to the bedbar surface. Clean the screw threads. Apply thread-locking compound to the screws and install the bedknife to the bedbar. g255046 Figure 28 1.
Note: Additional instructions and procedures on Backlapping are available in your traction unit Operator’s Manual and the Toro Sharpening Reel and Rotary Mowers Manual, Form Number 80-300PT. Note: For a better cutting edge, run a file across the front face of the bedknife and reel when the lapping operation is completed.
Page 19
The method of transmission shall be electronic transmittal. This machinery shall not be put into service until incorporated into approved Toro models as indicated on the associated Declaration of Conformity and in accordance with all instructions, whereby it can be declared in conformity with all relevant Directives.
Page 20
Countries Other than the United States or Canada Customers who have purchased Toro products exported from the United States or Canada should contact their Toro Distributor (Dealer) to obtain guarantee policies for your country, province, or state. If for any reason you are dissatisfied with your Distributor's service or have difficulty obtaining guarantee information, contact the Toro importer.