Bosch MD-200 User Manual page 47

ss02789
Automated System Test Report
2007 Jeep Wrangler Unlimited X 3.8L
SUMMARY Mode 2 Freeze Frames
DTCs
Evaporative Emissions
DATA STREAM SNAPSHOT
System Vapor Pressure
MODE 1
16.06
inH2O
FREEZE FRAME
MODE 5
Catalyst Temperature
Bank 1 Sensor 1
MODE 6
Mode 2 displays recorded data in the form of a DS
snapshot by the vehicle's computer when specific
DTC are set and the MIL is illuminated.
Mode 5 (Oxygen sensor tests)
Mode 5 views O2 sensor monitor test results.
ss02790
Automated System Test Report
2007 Jeep Wrangler Unlimited X 3.8L
SUMMARY Oxygen Sensor Tests (Mode 5)
DTCs
Description
DATA STREAM SNAPSHOT
Bank 1 Sensor 1
MODE 1
Maximum Sensor Voltage For Test Cycle
FREEZE FRAME
Lean To Rich Sensor Threshold Voltage
MODE 5
High Sensor Voltage For Switch Time
Calculation
MODE 6
Minimum Sensor Voltage For Test Cycle
Mode 5 views O2 sensor monitor test results. Mode
5 displays the average of the O2 sensor monitor
test results measured over a period of time. The
parameters of this measurement vary between
manufacturers. It may be necessary to run the
vehicle for a period of time to allow the O2 sensors
to fully warm up and begin operating.
Note: Mode 5 is not supported on all vehicles.
Mode 6 (Non-continuous monitor tests)
Mode 6 views onboard monitoring test results for
noncontinuous monitor systems.
©Mitchell International, Inc.
Clear Refresh Share Save Menu
Distance MIL Active Distance Since DTC Clear
13026 3881
miles miles
Catalyst Temperature Catalyst Temperature
Bank 1 Sensor 2 Bank 2 Sensor 1
Clear Refresh Share Save Menu
Min Value Max Units
0.000 0.003 1.275 V
0.000 0.003 1.275 V
0.000 0.003 1.275 V
0.000 0.003 1.275 V
User Manual | Mitchell Diagnostics | Scan Tool | 45 | en
ss02791
Automated System Test Report
2007 Jeep Wrangler Unlimited X 3.8L
SUMMARY Non-Continuously Monitored Tests
(Mode 6)
DTCs
DATA STREAM SNAPSHOT
ECU: ENGINE
MODE 1
TID 1 TID 1
CID 1 TID 1
FREEZE FRAME
N/A
MIN
MODE 5
TID 2 TID 2
CID 2 TID 2
MODE 6
Non-Continuous Monitor Tests (Mode 6) are pass/
fail tests, including certain EVAP tests, catalyst, and
EGR. The following information is reported:
• ECU.
• TID (test identification) indicates the system
monitor.
• CID (component identification) indicates the
component tested and its test value.
• Minimum value, maximum value, and current
value for each non-continuous monitor.
• Pass or fail test result.
Each vehicle manufacturer assigns a code number
to their system monitors and components. Refer
to the vehicle manufacturers Mode 6 code chart to
determine the failure indicated by the TID and CID. If
this chart is not readily available, run an automated
system test (AST) from the DTC screen and select
Mode 6. See Read DTCs section for more information
regarding steps to complete this action. This may
provide a more detailed description of the Mode 6
test information.
Automated System Test (AST) Button
Definitions
Refresh DTCs Button
Tapping the Refresh button initiates a
fresh scan of DTCs from the vehicle.
Share DTCs Button
Tapping the Share button opens the
app and initiates options. Depending on
what's available at the time. Share a list
containing all the DTCs set by email or
Bluetooth or USB.
581624 | REV. B | 06.2017 | APDMD032018
Clear Refresh Share Save
Passed
9667 25292 N/A
VALUE MAX UNITS
Failed
Menu