Page 2
• Programming via standard JTAG Overview • Evaluation kit with pre-installed web application for The PAN9420 is a 2.4 GHz ISM band quick prototyping available Wi-Fi-embedded module which includes a wireless • Evaluation and development tool WiFigurator for radio and an MCU for easy integration of Windows Wi-Fi connectivity into various electronic devices.
Page 3
By purchase of any of the products described in this document the customer accepts the document's validity and declares their agreement and understanding of its contents and recommendations. Panasonic reserves the right to make changes as required at any time without notification. Please consult the most recently issued Product Specification before initiating or completing a design.
This Product Specification provides details on the functional, operational, and electrical characteristics of the Panasonic PAN9420 module. It is intended for hardware design, application, and OEM engineers. The product is referred to as “the PAN9420” or “the module” within this document.
2 Overview 2 Overview The PAN9420 is a 2.4 GHz 802.11 b/g/n embedded Wi-Fi module with integrated stack and API that minimizes firmware development and includes a full security suite. The module is specifically designed for highly integrated and cost-effective applications. The module includes a fully shielded case, integrated crystal oscillators, and a chip antenna.
PAN9420 Wi-Fi Module 2 Overview 2.2 Pin Configuration Pin Assignment Pin Functions No Pin Name Pin Type Description 1 GND Ground Pin Connect to ground 2 GPIO4 Digital I/O Digital I/O #4 3 GPIO5 Digital I/O Digital I/O #5...
Page 9
PAN9420 Wi-Fi Module 2 Overview No Pin Name Pin Type Description RF in/out over 50Ω bottom pad 16 NC/RF NC/Analog IO 17 GND Ground Pin Connect to ground 18 GND Ground Pin Connect to ground 19 GND Ground Pin...
Page 10
PAN9420 Wi-Fi Module 2 Overview No Pin Name Pin Type Description A5 SPDT V2 Input Signal Do not connect if on-board antenna In/Out is desired, for RF-Pad 4.3.2 Module Selectable In/Out RF-In/Output. B1 NC Do not connect B2 NC...
PAN9420 Wi-Fi Module 3 Detailed Description 3.2 Footprint The outer dimensions have a tolerance of 0.35 mm. Product Specification Rev. 1.1 Page 15...
PAN9420 Wi-Fi Module 3 Detailed Description 3.3 Packaging The product is a mass production status product and will be delivered in the package described below. 3.3.1 Tape Dimensions 3.3.2 Packing in Tape Empty spaces in the component packed area shall be less than two per reel and those spaces shall not be consecutive.
Page 18
PAN9420 Wi-Fi Module 3 Detailed Description 3.3.5 Package Label Example (1T) Lot code (1P) Customer order number, if applicable (2P) Order number (9D) Date code Quantity (HW/SW) Hardware/Software version 3.3.6 Total Package moisture-sensitive print (already exist on barrier bag)
PAN9420 Wi-Fi Module 3 Detailed Description 3.4 Case Marking Example for PAN9420 (FCC version) Brand name Hardware/Software version Engineering Sample (optional) Model Name/ENW number Lot code Serial number WLAN MAC address FCC ID IC Canada Marking for Pin 1 2D-barcode, for internal usage only Product Specification Rev.
PAN9420 Wi-Fi Module 4 Specification 4 Specification All specifications are over temperature and process, unless indicated otherwise. 4.1 Default Test Conditions Temperature: 25 ± 10 °C Humidity: 40 to 85 % RH Supply Voltage: 3.3 V 4.2 Absolute Maximum Ratings The maximum ratings may not be exceeded under any circumstances, not even momentarily or individually, as permanent damage to the module may result.
PAN9420 Wi-Fi Module 4 Specification 4.3 Recommended Operating Conditions The maximum ratings may not be exceeded under any circumstances, not even momentarily or individually, as permanent damage to the module may result. Symbol Parameter Condition Min. Typ. Max. Units...
Page 22
PAN9420 Wi-Fi Module 4 Specification 4.3.3 Current Consumption The current consumption depends on the user scenario and on the setup and timing in the power modes. Assume V = 3.3 V, T = 25 °C, if nothing else stated.
Page 23
PAN9420 Wi-Fi Module 4 Specification 4.3.5 Power Up Sequence When the power is turned on, set reset signal to low (RESETn = low). After the V is stable, release the reset (RESETn = high). Resetn FW boot FW application Firmware 4.3.6...
Page 24
PAN9420 Wi-Fi Module 4 Specification 4.3.7 Host Interface Specification 4.3.7.1 UART0 Command Interface Bus Signals Module Pin No Signal Name Function Description 27 UART0 TXD Transmit data output Command 28 UART0 RXD Receive data input Protocol Item Range Default...
Page 25
PAN9420 Wi-Fi Module 4 Specification 4.3.7.2 UART1 Binary Data Interface Bus Signals Module Pin No Signal Name Function Description 9 UART1 CTS Clear to send 10 UART1 RTS Request to send Binary data 11 UART1 TXD Transmit data output...
Page 26
PAN9420 Wi-Fi Module 4 Specification 4.3.7.3 UART1 Dual Interface Bus Signals Module Signal Name GPIO GPIO Level State Default Description Pin No Definition Default 9 UART1 CTS Clear to send 10 UART1 RTS Request to send 11 UART1 TXD...
Page 27
PAN9420 Wi-Fi Module 4 Specification Bus and Control Timing Diagram MCU Ready Booting Ready state Host UART1 DUAL SW Default Host UART1 DUAL STAT Default Binary state Command state Binary state Host UART1 Pre-set toggle Set toggle Reset toggle...
Page 28
PAN9420 Wi-Fi Module 4 Specification Firmware-Defined GPIOs GPIO Pin GPIO GPIO Level Firmware State Name Definition Input Out- Default Active Boot Firmware Application Firmware Function Active STAT LED1 OFF: Shut-off MCU status (heartbeat) BLINK (1sec): Firmware active STAT LED2...
PAN9420 Wi-Fi Module 4 Specification 4.5 Reliability Tests The measurement should be done after the test device has been exposed to room temperature and humidity for one hour. No. Item Limit Condition Freq.: 20~2 000 Hz; 17g~50g /cycle, 1 Vibration test Electrical parameter should be in 2 hrs.
PAN9420 Wi-Fi Module 4 Specification 4.6 Recommended Soldering Profile Reflow permissible cycle: 2 Opposite side reflow is prohibited due to module weight More than 75 percent of the soldering area shall be coated by solder ...
PAN9420 Wi-Fi Module 5 Cautions, Life Support Policy, RoHS Declaration, and Regulatory Information 5 Cautions, Life Support Policy, RoHS Declaration, and Regulatory Information 5.1 Cautions Failure to follow the guidelines set forth in this document may result in degrading of the product’s functions and damage to the product.
Page 36
PAN9420 Wi-Fi Module 5 Cautions, Life Support Policy, RoHS Declaration, and Regulatory Information 5.1.3 Usage Condition Notes 1. Take measures to protect the unit against static electricity. If pulses or other transient loads (a large load applied in a short time) are applied to the products, check and evaluate their operation befor assembly on the final products.
Page 37
7. When you have any question or uncertainty, contact Panasonic. Product Specification Rev. 1.1 Page 37...
5 Cautions, Life Support Policy, RoHS Declaration, and Regulatory Information 5.2 Life Support Policy This Panasonic Industrial Devices Europe GmbH product is not designed for use in life support appliances, devices, or systems where malfunction can reasonably be expected to result in a...
Page 39
FCC Notice above. The FCC identifier is FCC ID: T7V-9420 for model ENW49C01A3KF. This FCC identifier is valid for the PAN9420. The end product must in any case be labelled on the exterior with: “Contains FCC ID: T7V-9420”.
Page 40
(FCC ID: T7V-9420 for model ENW49C01A3KF) are fulfilled for mobile configuration. The installation of the module is restricted to mobile host devices. Nevertheless, the PAN9420 shall be used in such a manner that the potential for human contact during normal operation is minimized.
Page 41
PAN9420 Wi-Fi Module 5 Cautions, Life Support Policy, RoHS Declaration, and Regulatory Information French PAN9420 (et ses versions) est garanti conforme aux dispositions règlementaires d’Industry Canada (IC). Licence pour M/N: ENW49C01A3KF: IC: 216Q-9420 Licence pour M/N: ENW49C02A3KF: IC: 216Q-9420 Il est recommandé...
Page 42
The Original Equipment Manufacturer (OEM) must ensure that IC labelling requirements are met. This includes a clearly visible label on the outside of the OEM enclosure specifying the appropriate Panasonic IC identifier for this product as well as the IC Notice above.
Page 43
The end customer equipment must meet the actual Safety/Health requirements according to RED. PAN9420 and its model versions in the specified reference design can be used in all countries of the European Economic Area (Member States of the EU, European Free Trade Association States[Iceland, Liechtenstein, Norway]), Monaco, San Marino, Andorra, and Turkey.
Regulatory notice: ETSI for EU and other Supported channel: Channel 1 ~ 13, 2412 ~ 2472 MHz The PAN9420 is delivered with a pre-installed firmware. For further information please refer to 6.2.2 Product Information. our product documentation Abbreviation for Minimum Order Quantity (MOQ). The standard MOQ for mass production is 500 pieces, fewer only on customer demand.
For Panasonic Sales assistance in the EU, visit https://eu.industrial.panasonic.com/about-us/contact-us Email: wireless@eu.panasonic.com For Panasonic Sales assistance in North America, visit the Panasonic Sales & Support Tool to find assistance near you at https://na.industrial.panasonic.com/distributors Please visit the Panasonic Wireless Technical Forum to submit a question at https://forum.na.industrial.panasonic.com...