Page 1
SERVICE MANUAL DVD VIDEO PLAYER XA002 2003 XV-N30BK[MK2], XV-N33SL[MK2] Area Suffix J -------------------------- U.S.A. C --------------------- Canada B -------------------------- U.K. E ------ Continental Europe EN ------- Northern Europe EV --------- Eastern Europe EE ---- Russian Federation For only Europe STANDBY/ON DISPLAY TITLE/ 3D PHONIC...
Page 2
For this service manual This service manual is a service manual of the model which changes a part of specification of the above-mentioned model which has already been put on the market. <When the label in figure is pasted in the main body> The specification is different from what the label of the same model does not paste because of the specification improvement, and refer to this service manual, please.
Page 3
SPECIFICATION (For U.S.A.) General Readable discs DVD VIDEO, DVD-R (Video format), DVD-RW (Video format), +RW (Video format), SVCD, Video CD, Audio CD (CD-DA), MP3 format, CD-R/RW (CD-DA, SVCD, Video CD, MP3 format) Video format NTSC Other Power requirements AC 120 V, 60 Hz Power consumption 10 W (POWER ON) 0.7 W (STANDBY mode) Mass...
SECTION 1 Important Safety Precautions Safety Precautions (1) This design of this product contains special hardware and path to the chassis, and measure the AC voltage across many circuits and components specially for safety purpos- the resistor. Now, reverse the plug in the AC outlet and es.
Page 5
Preventing static electricity Electrostatic discharge (ESD), which occurs when static electricity stored in the body, fabric, etc. is discharged, can destroy the laser diode in the traverse unit (optical pickup). Take care to prevent this when performing repairs. 1.5.1 Grounding to prevent damage by static electricity Static electricity in the work area can destroy the optical pickup (laser diode) in devices such as DVD players.
Page 7
Important for laser products (1) CLASS 1 LASER PRODUCT (5) CAUTION : If safety switches malfunction, the laser is able (2) DANGER : Invisible laser radiation when open and inter to function. lock failed or defeated. Avoid direct exposure to beam. (6) CAUTION : Use of controls, adjustments or performance of (3) CAUTION : There are no serviceable parts inside the procedures other than those specified herein may result in...
1.10 Precautions for Service 1.10.1 Handling of Traverse Unit and Laser Pickup (1) Do not touch any peripheral element of the pickup or the actuator. (2) The traverse unit and the pickup are precision devices and therefore must not be subjected to strong shock. (3) Do not use a tester to examine the laser diode.
Page 9
SECTION 2 Disassembly method There is a part different from the photograph according to the model and the destination though explains this disassembly method by using XV-N30BK for U.S.A. Main body section 2.1.1 Removing the top cover (See Figure 1) (1) Remove the two screws A attaching the top cover on both sides of the main body.
Page 10
2.1.3 Removing the mechanism assembly (See Figure 2, Figure 5) • Prior to performing the following procedure, remove the top Mechanism assembly cover. • There is no need to remove the front panel assembly. (1) Insert a kind of screwdriver in a hole located in the right side of mechanism assembly, and push a lever until it can- not be inserted any further.
Page 11
2.1.5 Removing the rear panel (See Figure 8, Figure 9) • Prior to performing the following procedure, remove the top Rear panel cover. (1) Remove the five screws E attaching the rear panel. (2) Disconnect the power cord from connector P901 on the power supply board (3) Remove tie band.
Page 12
Loading mechanism assembly 2.2.1 Removing the tray (See Figure 1, Figure 2, Figure 3, Figure 4, Figure 5, Figure 6) (1) Push a of the slide cam on the hole in the right side of the Tray loading base by using a driver until it stops. (See Figure 1.) (2) The tray comes out.
Page 13
2.2.2 Removing the traverse mechanism assembly (See Figure 7) Reverse the loading mechanism assembly. Remove the four Loading mechanism assembly screws B attaching the traverse mechanism assembly. Remove the traverse mechanism assembly upward. Traverse mechanism assembly Fig.7 2.2.3 Removing the elevator (See Figure 8 and Figure 9) •...
Page 14
2.2.4 Removing the loading motor (See Figure 10 and Figure 11) • Prior to the following procedure, remove the tray, the traverse Loading base Belt mechanism assembly, and the elevator. (1) Remove the belt from the pulley. Pulley Slide cam Pulley (2) Remove two screws C attaching the loading motor.
Page 15
Traverse mechanism assembly 2.3.1 Removing the pickup (See Figure 12, Figure 13) • Prior to the following procedure, remove the traverse mecha- nism assembly. (1) Remove one screw D attaching the plate. (2) Remove the plate and the leaf spring. (3) Lift i of the shaft 1, and pull out the shaft 1 from j.
SECTION 3 Adjustment Test mode setting method (1) Unplug the power plug. (2) Insert power plug into outlet while pressing both "PLAY" key and "STOP" key of the main body. (3) The FL display shows " 0", and the main body turns to test mode. " " means the destination, and "0" means parameter adjust- ment status.
Page 17
All-initialization method Please perform all-initialization according to the following procedures in the following case: • Just after you exchange the pick-up. • Just after you exchange the spindle motor. • Just after you exchange the traverse mechanism base. NOTE: Please perform all-initialization when you exchange the parts above and also when you remove the parts above. •...
Page 18
Display of current value of laser (1) Set the main body at test mode. (2) Press "CHOICE" key of the remote controller three times. Then, FL display is displayed "CK". (3) The laser current value can be switched between the value of CD and that of DVD by pressing the following key of the remote controller.
Page 19
3.7.1 Tool for adjustment *Stud: One set (four studs), Part number: JIGXVS40 (Note: One of the four studs is not used here.) * Relay board and extension cord (One set) --- Parts number : EXTXVN30CB -- Items -- Relay board 1 : EXTXVN30CB-1 Relay board 2 : EXTXVN30CB-2 Relay board 3 : EXTXVN30CB-3 Relay board 4 : EXTXVN30CB-4...
Page 20
3.7.3 Adjustment (1) Set the main body at test mode. (2) Press the "CHOICE" key of the remote controller three times, and the FL display is displayed "CK". (3) Insert a test disc (VT-501), and press the "PLAY" key of the main body. (4) After a few seconds, press the numeric key "6"...
Page 21
Set the main body at test mode, and check that the FL display shows " 0". Opening picture check (Power ON) It should be display "JVC" Muting working The noise must not be had to the performance beginning when you push "PLAY" button or at ON/STANDBY.
Page 22
3.10 Troubleshooting 3.10.1 Servo volume Press OPEN /CLOSE key Is tray Confirmation of tray drive circuit operation and circuit in surrounding correct? Is the traverse moving See "(3) Traverse movement error" along the innermost in "Check points for individual errors" perimeter for SW detection? "NO DISC"...
Page 23
3.11 Check points for each error 3.11.1 Spindle start error (1) Defective spindle motor • Are there several ohms resistance between each pin of CN201 "1-2","2-3","1-3"? (The power supply is turned off and measured.) • Is the sign wave of about 100mVp-p in the voltage had from each terminal? [ CN201"10"(H1+),"11"(H1-),"7"(H2+),"8"(H2-),"5"(H3+),"6"(H3-) ] (2) Defective spindle motor driver (IC251) •...
Page 24
3.11.6 Spindle CLV NG • IC101 -- "30"(ARF-), "31(ARF+). • Does not the input or the output of driver's spindle signal do the grip? • Has the tracking been turned on? • Spindle motor and driver is defective. • Additionally, "IC101 and IC301" and "Mechanism is defective(jitter)", etc. are thought. 3.11.7 Address read NG •...
SECTION 4 Description of major ICs 74LCX373MTC-X (IC512,IC513) : Octal D-type latch • Pin layout • Truth table INPUTS OUTPUT H = HIGH Voltage levelL = LOW Voltage levelZ = High imped- anceX = ImmaterialQ0 = Previous Q0 before HIGH to LOW transition of latch enable (TOP VIEW) •...
Page 30
BA6664FM-X (IC251) : Spindle motor driver • Pin layout • Block diagram DRIVER GAIN SWITCH GAIN CONTROL CURRENT SENSE AMP HALL AMP TOROUE SENSE AMP SHORT BRAKE CK Q BRAKE MODE Hall Bias 1-30 (No.XA002)
Page 31
• Pin function (BA6664FM-X) Pin No. Symbol Description Non connect Output 3 for spindle motor Non connect Output 2 for spindle motor Non connect Non connect Output 1 for spindle motor Connect to ground Positive input for hall input AMP 1 Negative input for hall input AMP 1 Positive input for hall input AMP 2 Negative input for hall input AMP 2...
Page 32
BA5983FM-X (IC201) : 4-channel driver • Block diagram STAND BY Level Shift Level Shift Level Shift Level Shift STAND BY CH1/2/3 • Pin function Pin No. Symbol Description Pin No. Symbol Description VO4(-) O Inverted output of CH4 BIAS IN Input for Bias-amplifier VO3(+) O Non inverted output of CH3...
Page 33
SST39VF160-7DD (IC509) : 16M EEPROM • Pin layout /BYTE /RST • Block diagram 16,777,216Bit EEPROM X-Decoder Cell Array A19~A0 Address Buffer & Latches Y-Decoder Control Logic I/O Buffers & Data Latches DQ15~DQ0 • Pin function Symbol Pin name Function A19~A0 Address Inputs To provide memory addresses.
Page 34
JCE8044 (IC501) : AV Decoder • Pin layout • Block diagram digital audio Video I/O port audio DAC NTSC Audio MPEG Video Audio digital audio output Video output Video SCART processor decoder processor encoder Serial XBUS serial XBUS port controller peripherals controller RISC...
Page 35
Pin No. Symbol Description 25,26 MA2,1 SDRAM Address bus terminal VDDio Power supply terminal 3.3V SDRAM Address bus terminal MA10 SDRAM Address bus terminal MA11 Non connect VSSio Connect to ground 32,33 MA12,13 SDRAM Address bus, reserved for terminal compatibility with 64Mb SDRAM Power supply terminal 1.8V SDRAM Primary bank chip select VDDio...
Page 36
Pin No. Symbol Description VSSio Connect to ground RXD1 UART1 Serial data input from external serial device, used for IR receiver SSPIN1 SSP1 Data in or 16X clock for USART function in UART1 Connect to ground SSPOUT1 SSP1 Data out or UART1 data-terminal-ready signal SSPCLK1 SSP1 Clock or UART1 clear-to -send signal SSPCLK0...
Page 37
Pin No. Symbol Description TRVSW Non connect HFMON Non connect SBAK Non connect HAGUP Non connect VI02 Non connect VSSio Connect to ground DRVMUTE Non connect SPMUTE Non connect Power supply terminal 1.8V 136~139 AD31~28 Multiplexed address / data bus terminal VDDio Power supply terminal 141~144...
Page 38
Pin No. Symbol Description ADSCIRQ Interrupt input VSSio Connect to ground XI09 Programmable general purpose external input/output 206~208 XID10~12 Programmable general purpose external input/output ODCIRQ Interrupt input VDDio Power supply terminal 3.3V ODCIRQ2 Interrupt input Power supply terminal 1.8V DSYNC DVD Parallel mode sector sync ODCIRQ2 Interrupt input...
Page 39
UPD789074MC-024 (IC701) : System controller • Pin layout GAINCNT S/COMP FASTPLAY RESET E/OTHER LMUTE AVCO P.ON/STANDB CPURST TCLOSE MUTE TOPEN FLDIN AVCI FLDOUT REMO FLCLK SWCLOSE FLSTB SWOPEN INTP • Pin function Pin No. Symbol Description NTSC(L)/PAL(H) switching signal input S/COMP S(L)/COMPORNENT(H) output switching signal input The power supply for on board to writing...
Page 40
MN103S26EDC-H (IC301) : Super optical disc controller • Terminal layout • Block diagram Host I/F DVD-ROM Analog MPEG I/F Formatter CD-PRE ATAPI High speed IO bus Instruction Servo I/O CGEN memory (core 1 I/O) (40KB) 32 bit CPU core 2Mbit Servo core Data DRAM...
Page 41
Pin No. Symbol Description System control chip select Writing system control Read signal input from system controller 37~44 CPUDT7~0 I/O System control data CLKOUT1 Non connect MMOD Test mode switch signal NRST System reset MSTPOL Master terminal polarity switch input SCLOCK Non connect SDATA...
Pin No. Symbol Description LOUT Non connect AVDD Power supply terminal for analog circuit (3.3V) VCOF JFVCO control voltage TRCRS Input signal for track cross formation CMPIN Non connect LPFOUT Non connect LPFIN Pull-up to VHALF AVSS Connect to ground for analog circuit HPFOUT Non connect HPFIN...
Page 44
4.10 W986432DH-7 (IC505) : 32 Bits SDRAM • Pin layout • Pin function Pin No. Symbol Function Power for input buffers and logic circuit inside DRAM. (+3.3V) Multiplexed pins for data out put and input. VccQ Separated power from VCC, to improve DQ noise immunity. (+3.3V) DQ1~DQ2 Multiplexed pins for data out put and input.
Page 45
Pin No. Symbol Function 39-40 DQ21~22 Multiplexed pins for data out put and input. VccQ Separated power from VCC, to improve DQ noise immunity. (+3.3V) DQ23 Multiplexed pins for data out put and input. Power for input buffers and logic circuit inside DRAM. (+3.3V) Ground for input buffers and logic circuit inside DRAM.
Page 46
• Block diagram Clock buffer Control signal generator Command buffer Column decoder Column decoder Cell array Cell array bank #0 bank #1 Mode Sense amplifier Sense amplifier register Address buffer Data control buffer circuit DQ31 DQM0~3 Column Refresh counter counter Column decoder Column decoder Cell array...
Page 48
VICTOR COMPANY OF JAPAN, LIMITED AV & MULTIMEDIA COMPANY OPTICAL DISC CATEGORY 1644, Shimotsuruma, Yamato, Kanagawa 242-8514, Japan (No.XA002) Printed in Japan...
XV-N30BK,XV-N33SL SCHEMATIC DIAGRAMS DVD VIDEO PLAYER XV-N30BK[MK2], XV-N33SL[MK2] CD-ROM No.SML200306 Area Suffix J -------------------------- U.S.A. C --------------------- Canada B -------------------------- U.K. E ------ Continental Europe EN ------- Northern Europe EV --------- Eastern Europe EE ---- Russian Federation For only Europe STANDBY/ON DISPLAY TITLE/...
Page 50
XV-N30BK/XV-N33SL In regard with component parts appearing on the silk-screen printed side (parts side) of the PWB diagrams, the parts that are printed over with black such as the resistor ( diode ( ) and ICP ( ) or identified by the " " mark nearby are critical for safety. When replacing them, be sure to use the parts of the same type and rating as specified by the manufacturer.
Page 66
XV-N30BK/XV-N33SL VICTOR COMPANY OF JAPAN, LIMITED AV & MULTIMEDIA COMPANY OPTICAL DISC CATEGORY 1644, Shimotsuruma, Yamato, Kanagawa 242-8514, Japan Printed in japan No.XA002SCH 200306(V)
XV-N30BK,XV-N33SL PARTS LIST [XV-N30BK,XV-N33SL] [MK2] * All printed circuit boards and its assemblies are not available as service parts. * (x_) in a description column shows the number of the used part. Area Suffix J -------------------------- U.S.A. C --------------------- Canada B -------------------------- U.K.
XV-N30BK,XV-N33SL Exploded view of general assembly and parts list Block No.M1MM Grease JVS-1003 BACK SIDE Operation "B" switch board Power supply & Audio/Video system control output board board display board "A" "B" BACK SIDE Servo control board "A" 3-2(No.XA002)
Page 69
XV-N30BK for Europe GN10037-004A FRONT PANEL XV-N30BK for ver.J/C GN10037-009A FRONT PANEL XV-N33SL for Europe GN10037-010A FRONT PANEL XV-N33SL for ver.J/C GN40020-001A JVC MARK only XV-N30BK GN40020-002A JVC MARK only XV-N33SL GN20041-001A WINDOW SCREEN GN20040-003A PUSH BUTTON POWER only XV-N30BK...
XV-N30BK,XV-N33SL DVD Traverse mechanism assembly and parts list Block No.M2MM EXL-V10-1C Grease =JVG-31N =CFD-4007ZY2 =PG-641 =1401C < BACK SIDE > 63.3mm 0.1mm 10.5mm 0.1mm 3-4(No.XA002)
Page 71
XV-N30BK,XV-N33SL DVD Traverse mechanism Block No. [M][2][M][M] Symbol No. Part No. Part Name Description Local LE20697-002A MECHA BASE LE20699-001A SPINDLE BASE QYSDST2604M TAPPING SCREW 2.6mm x 4mm(x2) LE40931-001A SHAFT LV33991-001A ADJUST SPRING QYSPSFU2040M TAPPING SCREW M2 x 4mm LE20698-001A FEED HOLDER QAR0215-001 FEED MOTOR...
XV-N30BK,XV-N33SL DVD Loading mechanism assembly and parts list Block No.M3MM ELM-J2-1C Grease JVG-31N JVS-1003 (All circumferenced) BACK SIDE switch board 3-6(No.XA002)
Page 73
XV-N30BK,XV-N33SL DVD Loading mechanism Block No. [M][3][M][M] Symbol No. Part No. Part Name Description Local LE10275-002A LOADER BASE LE31043-001A PULLEY GEAR LE31042-001A MIDDLE GEAR LE20665-001A SLIDE CAM LE20666-001A ELEVATOR LE10276-002A TRAY LE31045-001A BUSHING LE40898-001A SHAFT QYSSSF2008Z TAP SCREW M2 x 8mm QAR0197-001 MOTOR LV42087-002A...
XV-N30BK,XV-N33SL Electrical parts list Servo control board Block No. [0][1] Symbol No. Part No. Part Name Description Local Symbol No. Part No. Part Name Description Local C263 NCF31CZ-104X C CAPACITOR 0.1uF 16V Z C264 NCB31CK-103X C CAPACITOR 0.01uF 16V K IC101 AN8703FH-V Frontend processor for DVD...
Page 75
XV-N30BK,XV-N33SL Symbol No. Part No. Part Name Description Local Symbol No. Part No. Part Name Description Local C551 NCB31CK-103X C CAPACITOR 0.01uF 16V K R324 NRSA63J-473X MG RESISTOR 47kΩ 1/16W J C554 NCF31CZ-104X C CAPACITOR 0.1uF 16V Z R325 NRSA63J-123X MG RESISTOR...
100uF 10V M only ver.J/C Q701 KRC107S-X DIGI TRANSISTOR only Europe C794 NCB31CK-104X C CAPACITOR 0.1uF 16V K only ver.J/C Q751 2SC3576-JVC-T TRANSISTOR C795 QETN1EM-476Z E CAPACITOR 47uF 25V M Q752 2SC3576-JVC-T TRANSISTOR C797 NDC31HJ-151X C CAPACITOR 150pF 50V J...
Page 77
XV-N30BK,XV-N33SL Symbol No. Part No. Part Name Description Local Symbol No. Part No. Part Name Description Local R655 NRSA63J-102X MG RESISTOR 1kΩ 1/16W J only Europe R961 NRSA63J-472X MG RESISTOR 4.7kΩ 1/16W J R657 NRSA63J-104X MG RESISTOR 100kΩ 1/16W J only Europe R962 NRSA63F-392X...
XV-N30BK,XV-N33SL Switch board Block No. [0][3] Symbol No. Part No. Part Name Description Local QGF1016F3-05 CONNECTOR FFC/FPC (1-5) QSW1007-001 DETECT SWITCH DET SW 3-12(No.XA002)
XV-N30BK,XV-N33SL Packing materials and accessories parts list Block No.M4MM INST BOOK SA FRONT INST BOOK SA only ver.[C][UF] INST JPEG INSERT BOOK SENTER SHEET SHEET LIST except ver.[J][C] J=REGIST only ver.[J] only ver.[J][A] CARD only ver.[J] only ver.[B][E][EN] only ver.[B] only ver.[EV][EE] only ver.[J][C] (No.XA002)3-13...
Page 80
XV-N30BK,XV-N33SL Packing and accessories Block No. [M][4][M][M] Symbol No. Part No. Part Name Description Local LE40932-003A INSERT SHEET only ver.B/E/EN LE40932-004A INSERT SHEET only ver.EV/EE LE40932-002A INSERT SHEET only ver.J/C GNT0024-001B INST BOOK English GNT0024-003B INST BOOK English only ver.B GNT0024-002B INST BOOK English,French...