Panasonic PT-DZ6710 Specification Sheet
Panasonic dlp projector specification sheet
Hide thumbs
Also See for PT-DZ6710:
- Functional instructions (52 pages) ,
- Specification sheet (10 pages) ,
- Functional instructions (52 pages)
Related Manuals for Panasonic PT-DZ6710
Summary of Contents for Panasonic PT-DZ6710
- Page 1 PT-DZ6710/DZ6710L P ro d u c t N u m b e r : P ro d u c t N a m e : As of February 2009. Specifications subject to change without notice. The PT-DZ6710L is not equipped with a lens.
-
Page 2: Specifications
Main Unit Power supply: North America: Europe: Power consumption: North America: Europe: DLP™ chip: Panel size: Display method: Pixels: Lens: PT-DZ6710: PT-DZ6710L: Lamp: Screen size: Brightness* Center-to-corner uniformity* Contrast* Resolution: Scanning frequency: RGB/DVI-D: S-Video/Video: Optical axis shift: Keystone correction range:... - Page 3 S-VIDEO IN: SERIAL IN: SERIAL OUT: REMOTE 1 IN: REMOTE 1 OUT: REMOTE 2 IN: LAN: Power cord length: Cabinet materials: Dimensions (W x H x D): PT-DZ6710: PT-DZ6710L: Weight: PT-DZ6710: PT-DZ6710L: Operating temperature: Operating humidity: Remote Control Unit Power supply:...
- Page 4 DVI-D I N RGB 2 Input DVI-D input LAN connector unit : mm (inch) NOTE: This illustration is not drawn to scale. The illustration shows the PT-DZ6710. Remote 1 input Remote 1 output Remote 2 input 10 Serial input 11 Serial output 12 SDI input <...
-
Page 5: Standard Setting-Up Position
If the lens shift function is used, the corners of images may not be displayed or images may remain out of focus in some cases. As of February 2009 PT-DZ6710/DZ6710L *1 When the lens protrudes to the maxi- mum. 185 mm (7-9/32˝) with the supplied lens 212 mm (8-11/32˝) with the ET-DLE150... -
Page 6: Projection Distance For 16:10 Aspect Ratio Screen
• At the shortest projection distance, the zoom lens characteristics may cause slight image distortion. • When vertical keystone correction is used, the image is corrected in the direction that reduces its projected size. • The brightness varies depending on the zoom setting. As of February 2009 PT-DZ6710/DZ6710L Distance to screen (L) Zoom ET-DLE250... -
Page 7: Projection Distance For 16:9 Aspect Ratio Screen
• At the shortest projection distance, the zoom lens characteristics may cause slight image distortion. • When vertical keystone correction is used, the image is corrected in the direction that reduces its projected size. • The brightness varies depending on the zoom setting. As of February 2009 PT-DZ6710/DZ6710L Distance to screen (L) Zoom ET-DLE250... - Page 8 • At the shortest projection distance, the zoom lens characteristics may cause slight image distortion. • When vertical keystone correction is used, the image is corrected in the direction that reduces its projected size. • The brightness varies depending on the zoom setting. As of February 2009 PT-DZ6710/DZ6710L Distance to screen (L) Zoom ET-DLE250...
- Page 9 • Distances calculated with the above equations will include a slight error. As of February 2009 PT-DZ6710/DZ6710L L (mm) = (diagonal screen size in inches) x 28.6 – 54.0 L (mm) = (diagonal screen size in inches) x 41.3 – 49.8 L (mm) = (diagonal screen size in inches) x 39.5 –...
- Page 10 • Floor mount (Width of projected image) 0.1H Installable angle Install the projector at an angle within the range shown below. • Vertical direction The projector may be installed at a vertical angle of 360°. As of February 2009 PT-DZ6710/DZ6710L •...
- Page 11 NOTE: The native resolution of this projector is 1,920 x 1,200 pixels. If the display resolution of the input signal is different from the native resolution, image compression or expansion will be used to convert the input signal to a level within the native resolution.
- Page 12 • It may not be possible to send or receive commands for about 10 to 60 seconds when the lamp is first turned on. If this occurs, wait for 60 seconds, then try sending or receiving again. • When sending multiple commands, be sure to wait for at least 0.5 second after receiving a response from the projector before sending the next command.
- Page 13 * Do not send PON, POF, OSH, or OLP commands continuously in a short period of time. Doing so may burst the lamp or shorten the lamp replacement cycle. * When a command that cannot be executed during standby mode is sent, the projector will send an ER401 command in reply. As of February 2009...
- Page 14 Command example To set the on-screen display off, send the command as shown below. ADZZ Start ID Address NOTE: When sending commands without parameters, a colon (:) is not necessary. As of February 2009 PT-DZ6710/DZ6710L Callback p1p2p3p4p5 p1p2p3p4 p1p2p3p4 DLVI0=+00000 DLVI0=+00001...
- Page 15 * Even when the ambient temperature near the intake opening is 40°C/104°F or lower, an accumulation of hot air inside the cabinet may cause the protective circuit to activate and shut down the projector. Please give ample consideration to the design with regard to ambient temperature conditions.