5.2 Inner enclosure and upper frame removal 5.3 Control unit A 6. Parts Exploded View and Replacement Parts List 6.1 Parts Exploded View : Body 6.2 Parts Exploded View : Packing 6.3 Replacement Parts List : SR-TMJ181 15 - 16 panatex.com.ua - 2 -...
SR-TMJ181 1. SPECIFICATION MODEL SR-TMJ181 Countries Russia, Ukraine, Kazakstan Power Supply 220V / 50Hz / SH-3 Colour Name Stainless Colour Code Body Material Stainless steel / SUS Pan Material Aluminium / AL Power Consumption Cooking 670W Warming 108.5W Cooking Capacity...
SR-TMJ181 3. TROUBLESHOOTING GUIDE When receiving a rice boiler to be repaired, be sure to check that the main body is completely provide with the inner pan and the inner lid, ask the condition (phenmenon) of the trouble in detail. Before troubleshooting single parts, be sure to disconnect the power supply plug from the receptacle.
Page 7
SR-TMJ181 Condition Troubleshooting Remedy • Excessive burning. Does the center thermostat operate (More than light brown) • Replace the center thermostat. properly? (Check with the evaporation test). • Seeing at Table 2. Are the parts on the P.C.B. mistake? Improper operation •...
Page 8
SR-TMJ181 3.2 Table 2 Condition Troubleshooting Remedy • Rice is not boiling. • Replace the transformer. Is the transformer operating? (The indicating lamp does not come on) • Replace the P.C.B. complete. • Rice is not boiling. • Replace the relay.
SR-TMJ181 4. TESTING PROCEDURE 4.1 Bubbling test Input the pan in the main body, lightly rotate the pan clockwise and counter clockwise to settle the pan on the heating plate properly. 1. Fill water until center area of the pan bottom is dipped and close the lid. Then turn on the boiling switch.
SR-TMJ181 The above conditions are proper. Top view of pan Pan flange Holes on the tissue paper Tissue paper 4.3 Heat reserving test 1. Put approx. 1 liter of water and the thermometer [ repairing tool (mercury thermometer ASN-150H) ] in the pan, close the lid and turn on the boiling switch.
SR-TMJ181 5. DISASSEMBLY 5.1 Hinge Cover removal (Hinge Cover) 1. Remove the Dew Collector. 2. Remove the Hinge Cover mounting screws. 3. As show in the figure, insert a narrow flat head screwdriver from just below and pry off the Hinge Cover.
SR-TMJ181 5.3 Control Unit A 1. Use screwdriver take off Hinge Cover. (PIC-1) 2. Pull out at Hinge Shaft. (PIC-2) 3. Pull out at Wiring of Lid Heater and then pull out Outer Lid Assy. (PIC-3) PIC-1 PIC-2 PIC-3 4. Loosen screw at Bottom Frame and Body.
SR-TMJ181 Important safety notice : Components identified by mark have special characteristics important for safety. When replacing any of these components, use only manufacturer’s specified part. 6.3 Replacement Parts List : SR-TMJ181 Parts List MODEL / Q’TY REF. PART NAME PART NO.
SR-TMJ181 Parts List MODEL / Q’TY REF. PART NAME PART NO. SAFETY REMARK SR-TMJ181 NAME PLATE ARY30K9861VP INLET ARG10T92010U POWER CORD ASSY ARQ00T920-0U STEAM BASKET ARK53H6161W9 MEASURING CUP ASR792-454BK SCOOP ASR79WT281AK PCB COVER ARN32K986 Screws MODEL / Q’TY REF. PART NAME PART NO.
Page 17
Service Manual Мультиварка PANASONIC sr-tmj181 загружен с сайта руководства, инструкции, рецепты, http://www.panatex.com.ua характеристики, возможность просмотра, загрузить, скачать, бесплатно. panatex.com.ua...