Page 1
ORDER NO. MD0503056C3 Active Subwoofer System SB-WA730GCP Colour (S)...Silver Type Specification n Active subwoofer Type 1 way, 2 speaker system (Bass reflex) Note : Speaker unit(s) Impedance 4 Ω Specifications are subject to change without notice. 1. Woofer 13 cm Cone type Mass and dimensions are approximate.
SB-WA730GCP 5 Handling the Lead-free Solder 11.2. Transformer Circuit, AC Inlet Circuit and Voltage Selector 5.1. About lead free solder (PbF) Circuit 6 Connection of the Speaker Cables 12 Printed Circuit Board 7 Disassembly Procedure 12.1. Power P.C.B. 7.1. Disassembly flow chart 12.2.
SB-WA730GCP 1 Safety Precautions 1.1. GENERAL GUIDELINES 1. When servicing, observe the original lead dress. If a short circuit is found, replace all parts which have been overheated or damaged by the short circuit. 2. After servicing, ensure that all the protective devices such as insulation barriers, insulation papers shields are properly installed.
SB-WA730GCP 2 Before Use Be sure to disconnect the mains cord before adjusting the voltage selector. Use a minus (-) screwdriver to set the voltage selector (on the rear panel) to the voltage setting for the area in which the unit will be used.
SB-WA730GCP 6 Connection of the Speaker Cables · Be sure to connect speaker cables before connecting the AC power supply cord. · The load impedance of any speaker used with this unit must be 4Ω. · Be sure to connect the cable from the right speaker to the right terminal and the cable from the left speaker to the left terminal.
SB-WA730GCP 7 Disassembly Procedure “ATTENTION SERVICER” Some chassis components may have sharp edges. Be careful when disassembling and servicing. 1. This section describes procedures for checking the operation of the major printed circuit boards and replacing the main components. 2. For reassembly after operation checks or replacement, reverse the respective procedures.
SB-WA730GCP 7.1. Disassembly flow chart The following chart is the procedure for disassembling the casing and inside parts for internal inspection when carrying out the servicing. To assemble the unit, reverse the steps shown in the chart below. 7.1.1. Disassembly of Front Panel Assembly 7.1.2.
SB-WA730GCP 7.2. Disassembly of the Speaker Unit and Checking of the P.C.B. 7.2.1. Disassembly of the Front Panel Unit Step 3: Use the screwdriver to slightly lift up the Front Panel Unit as arrow shown. Step 1: Slot in a steel ruler to give a gap between the Front...
Page 9
SB-WA730GCP · Assembly of the Front Panel Unit. Step 1: Remove 4 screws from the Woofer 1. Step 1: Clean up all the glue at the 6 Boss points and replace with the normal glue. Step 2: Replace the Front Panel Unit firmly back to the Step 2: Remove the Woofer 1 by detaching the (+) and (-) cabinet.
Page 10
SB-WA730GCP Step 1: Remove 4 screws from the Woofer 2. Step 2: Remove 3 screws from the rear panel. Step 2: Remove the Woofer 2 by detaching the (+) and (-) wires. 7.2.4. Disassembly of the Power Amp Unit Step 3: Pull out the Power Amp Unit slightly as shown.
Page 11
SB-WA730GCP Step 3: Disconnect the Voltage Selector from the rear panel. Step 5: Pull out the entire Power Amp Unit. Step 4: Disconnect the connector (CN507) to detach the rear 7.2.5. Disassembly of the Rear Panel and panel. Fan Unit Follow Step (1) to Step (5) described in section 7.2.4.
Page 12
SB-WA730GCP 7.2.6. Disassembly and checking of the AC Inlet P.C.B., Power P.C.B. and Transformer P.C.B. Follow Step (1) to Step (5) described in section 7.2.4. Follow Step (1) to Step (4) described in section 7.2.5. Step 6: Remove 4 screws.
Page 13
SB-WA730GCP Step 1: Desolder the Power IC and Transistor terminal. Step 2: Remove 2 screws. and Power IC501. Step 3: Remove the screw and Transistor holder. Step 4: Detach the Power IC and Transistor from Heat sink.
SB-WA730GCP 8 Voltage Measurement and Waveform Chart Note: · Indicated voltage values are the standard values for the unit measured by the DC electronic circuit tester (high-impedance) with the chassis taken as standard. Therefore, there may exist some errors in the voltage values, depending on the internal impedance of the DC circuit tester.
SB-WA730GCP 8.2. Waveform CN501 PIN 1 CN501 PIN 3 CN501 PIN 8 CN501 PIN 21 CD PLAY CD PLAY CD PLAY CD PLAY 17.8Vp-p (10msec.div) 17.6Vp-p (10msec.div) 1.20Vp-p (10msec.div) 5.32Vp-p (10msec.div) CN501 PIN 22 CN501 PIN 24 CN503 PIN 1...
SB-WA730GCP 9 Block Diagram IC501 RSN311W64D-P POWER HIC POWER CONTROL CIRCUIT POWER CONTROL/PROTECTION CIRCUIT 12(11) (25) (19) D501 D502 Q506 INTERFACE SWITCH TO MAIN BLOCK Q505 (JK2000) OF SA-HT730GCP-S SWITCHING SL(R)/SURRL(R) FILTER JK501(JK502) SURROUND SPEAKER CCH/CENTRE FILTER JK502 CENTRE SPEAKER...
SB-WA730GCP 10 Notes of Schematic Diagram (All schematic diagrams may be modified at any time with the development of the new technology) Note: · The voltage value and waveforms are the reference voltage of this unit measured by DC electronic voltmeter (high impedance) and oscilloscope on the basis of chassis.
SB-WA730GCP 11 Schematic Diagram 11.1. Power Circuit SCHEMATIC DIAGRAM-1 : MAIN SIGNAL LINE : -B SIGNAL LINE POWER CIRCUIT : +B SIGNAL LINE C551 IC501 0.01 IC501 RSN311W64D-P POWER HIC E501 K4CZ01000027 R501 R513 4.7K R502 C507 18P 4.7K R514...
Page 19
SB-WA730GCP SCHEMATIC DIAGRAM-2 : MAIN SIGNAL LINE : -B SIGNAL LINE POWER CIRCUIT : +B SIGNAL LINE JK501 SRLch FRch FLch C519 C518 0.047 0.047 R534 R533 JK502 SRRch CENTER C569 0.047 C520 C523 C521 C522 0.047 0.047 0.047 0.047...
SB-WA730GCP 11.2. Transformer Circuit, AC Inlet Circuit and Voltage Selector Circuit SCHEMATIC DIAGRAM-3 : -B SIGNAL LINE : +B SIGNAL LINE Q518 B1AAGC000007 VOLTAGE REGULATOR C581 R588 820K 1000P C555 R589 35V4.7 Q516 R578 B1GACFJJ0016 SYNC SWITCH CN502 D530 D529...
SB-WA730GCP 13 Wiring Connection Diagram CN501 7..1 TO MAIN UNIT CN503 CP502 CENTER SPEAKER JK502 SURROUND RIGHT SPEAKER SURROUND LEFT SPEAKER FRONT RIGHT SPEAKER CN507 SPEAKER FRONT LEFT SPEAKER JK501 WOOFER CN506 SOLDER SIDE POWER P.C.B.
SB-WA730GCP 15 Parts Location and Replacement Parts List Notes: · Important safety notice: Components identified by mark have special characteristics important for safety. Furthermore, special parts which have purposes of fire-retardant (resistors), high-quality sound (capacitors), low noise (resistors), etc are used.
Page 29
SB-WA730GCP 15.1.2. Cabinet Parts List Ref. No. Part No. Part Name & Description Remarks CABINET AND CHASSIS RFKHBWA730PP SUB WOOFER CAB. ASSY XTB3+12GFJ SCREW B3AAA0000583 LED (RED) RGKX0284-H XTB4+12AFJ WOOD SCREW (TBZP) RKAX0019-KJ LEG CUSHION RYQX0167A-S FRONT PANEL UNIT RMQX0106...
SB-WA730GCP 15.2. Electrical Parts List Ref. No. Part No. Part Name & Description Remarks CN503 K1KA15A00159 15P CONNECTOR CN506 K1KA04A00105 4P CONNECTOR Ref. No. Part No. Part Name & Description Remarks CN507 K1KA02A00008 2P CONNECTOR PRINTED CIRCUIT BOARD CP502 K1KA07A00123...
Page 31
SB-WA730GCP Ref. No. Part No. Part Name & Description Remarks Ref. No. Part No. Part Name & Description Remarks R513 ERDS2TJ563T 56K 1/4W C508 ECBT1H180JC5 18P 50V R514 ERDS2TJ563T 56K 1/4W C509 ECBT1H220JC5 22P 50V R515 ERDS2TJ563T 56K 1/4W C510...
SB-WA730GCP 15.3. Packing Materials & Accessories Parts List Ref. Part No. Part Name & Description Remarks Ref. Part No. Part Name & Description Remarks PACKING MATERIALS RPNX0295 POLYFOAM (ASW) RPFX0071 MIRAMAT BAG 15.4. Packaging FLE0503/P/A/S/E/N/J...