Remove all tape and packing materials before using the oven. Dispose of all plastic bags after unpacking the oven. Never allow children to play with packing materials. You can download an installation manual at http://www.lg.com. IMPORTANT SAFETY INSTRUCTIONS Read and follow all instructions before using the oven to prevent the risk of fire, electric shock, injury to persons, or damage when using the oven.
IMPORTANT NOTE This installation must be completed by a qualified installer or technician. WARNING (For Model : LWS3081ST, LWD3081ST, LWS3010ST, LWD3010ST) - Failure to do so could result in fire or electrical shock, causing property damage, personal injury or death.
Part 2 INSTALLATION REQUIREMENTS The first step of the installation is measure the current cutout dimensions and compare them to the cutout IMPORTANT NOTE sure the base is level and the front of the cabinet is square. If the cabinet base is not level, the oven glides will tend to slide out when opening the door.
Page 5
Part 2 INSTALLATION REQUIREMENTS The first step of the installation is measure the current cutout dimensions and compare them to the cutout IMPORTANT NOTE two braces or runners must be installed level with the bottom of the cutout to support the weight of the oven. will tend to slide out when opening the door.
Page 6
Part 2 INSTALLATION REQUIREMENTS The first step of the installation is measure the current cutout dimensions and compare them to the cutout IMPORTANT NOTE braces or runners must be installed level with the bottom of the cutout to support the weight of the oven. will tend to slide out when opening the door.
Page 7
Part 2 INSTALLATION REQUIREMENTS The second step of the installation is to remove any packing material from the oven before installing the oven. 2. Open the oven door and remove packaging materials and oven racks inside the oven. 3. Door removal is not a requirement for installation of the oven, but is an added convenience. To remove the door, follow the steps below.
Part 3 ELECTRICAL CONNECTIONS The third step of the installation is to follow the electrical connection requirements below. Ensure that dedicated circuit protection is prepared as recommended and that the oven is grounded properly. IMPORTANT NOTE Be sure the wall oven is installed and grounded properly by a qualified installer or service technician. grounded branch circuit, protected by a circuit breaker or fuse.
Page 9
Part 3 ELECTRICAL CONNECTIONS The fourth step of the installation is to prepare the electrical connection as follows: 2. With the oven positioned directly in front of the cabinet opening, connect the flexible conduit to the electrical loop when the oven is installed. 5”...
Page 10
Part 3 ELECTRICAL CONNECTIONS IMPORTANT NOTE You will need to purchase an appropriate conduit connector to complete the connection of the conduit to the junction box. To connect to a three-wire circuit, follow these steps: To connect to a four-wire circuit, follow these steps: necessary.
Part 4 INSTALL THE OVEN The fifth step of the installation is to install the oven into the cabinet as follows: conduit from falling behind the oven. Do not push against outside edges. c. While sliding the oven back, pull the string so that the conduit lies on the top of the oven in a natural loop. d.
Page 12
Part 5 OPERATION CHECKLIST Each of the functions has been factory checked before shipping. However, it is suggested that you verify the 2. Check the operation of the broil mode. When the oven is set to broil, the upper element in the oven should convection mode, the back element should light up and the fan inside the oven should come on with door IMPORTANT NOTE workmanship or materials in this product.
MANUAL DE INSTALACIÓN HORNO ELÉCTRICO DE CONVECCIÓN EMPOTRADO Tenga a bien leer estas instrucciones por completo antes de instalar y operar el horno. LWS3081ST LWS3010ST LWS3063ST LSWS306ST LWS3063BD LWD3081ST LWD3010ST LWD3063ST LSWD306ST LWD3063BD www.lg.com P/No.: MFL51224802...
Quite toda la cinta y materiales de empaque antes de utilizar el horno. Deseche todas las bolsas plásticas después de desempacar el horno. Nunca permita que los niños jueguen con los materiales de empaque. Usted puede descargar el manual de instalación en http://www.lg.com. INSTRUCCIONES IMPORTANTES DE SEGURIDAD Lea y siga todas las instrucciones antes de utilizar su horno para evitar un riesgo de incendio, descarga eléctrica,...
Esta instalación debe completarla un instalador o técnico calificado. PROPIETARIO antes del uso. ADVERTENCIA HORNO (Para el modelo : LWS3081ST, LWD3081ST, LWS3010ST, LWD3010ST) - De no hacerlo, podría provocar un incendio o una descarga eléctrica, causando daños a la propiedad, lesiones personales o la muerte.
Parte 2 REQUISITOS DE INSTALACIÓN El primer paso de su instalación debe ser medir las dimensiones actuales de su abertura y compararlas con las dimensiones mostradas a continuación. Puede descubrir que será necesario realizar poco o nada de trabajo en los gabinetes. NOTA IMPORTANTE de que la base se encuentre nivelada y que el frente del gabinete esté...
Page 17
Parte 2 REQUISITOS DE INSTALACIÓN El primer paso de su instalación debe ser medir las dimensiones actuales de su abertura y compararlas con las dimensiones mostradas a continuación. Puede descubrir que será necesario realizar poco o nada de trabajo en los gabinetes. NOTA IMPORTANTE de que la base se encuentre nivelada y que el frente del gabinete esté...
Page 18
Parte 2 REQUISITOS DE INSTALACIÓN El primer paso de su instalación debe ser medir las dimensiones actuales de su abertura y compararlas con las dimensiones mostradas a continuación. Puede descubrir que será necesario realizar poco o nada de trabajo en los gabinetes. NOTA IMPORTANTE de que la base se encuentre nivelada y que el frente del gabinete esté...
Page 19
Parte 2 REQUISITOS DE INSTALACIÓN El segundo paso de su instalación debe ser quitar el material de empaque del horno antes de instalarlo. 3. La remoción de la puerta no es un requisito de la instalación del horno, pero es una comodidad agregada. Para quitar la puerta, siga los siguientes pasos.
Parte 3 CONEXIONES ELÉCTRICAS El tercer paso de su instalación debe ser seguir los requisitos de las conexiones eléctricas incluidos a continuación. Debe asegurarse que el circuito dedicado para protección se preparé como se recomienda y que el horno está correctamente conectado a tierra.
Page 21
Parte 3 CONEXIONES ELÉCTRICAS El cuarto paso de su instalación debe ser preparar la conexión eléctrica de la siguiente manera: conexiones eléctrica como se señala abajo. Coloque el conducto de modo que quede sobre el horno con un lazo natural cuando el horno se instale. 5”...
Page 22
Parte 3 CONEXIONES ELÉCTRICAS NOTA IMPORTANTE Tendrá que comprar un conector de conductos apropiado para completar la conexión del conducto a la caja de conexiones. Para conectar a un circuito de tres hilos, siga los Para conectar a un circuito de cuatro hilos, siga los siguientes pasos: siguientes pasos: fuera necesario.
Parte 4 INSTALACIÓN DEL HORNO El quinto paso de su instalación debe ser instalar el horno dentro del gabinete de la siguiente manera: permitirá que el conducto caiga detrás del horno. b. Levante el horno dentro de la abertura del gabinete utilizando el horno abierto como agarre. Con cuidado empuje desde el armazón frontal del horno.
Page 24
Parte 5 LISTA DE CONTROL DE FUNCIONAMIENTO Todas las funciones se han controlado en la fábrica antes del envío. Sin embargo, se sugiere que verifique el verificación básica. superior del horno debe ponerse rojo. Después de unos minutos, abra la puerta del horno parcialmente. Deberá NOTA IMPORTANTE comunes que no son el resultado de mano de obra o materiales defectuosos del producto.