Related Manuals for Bosch MIC-71 series
Summary of Contents for Bosch MIC-71 series
- Page 1 MIC IP starlight 7000 HD, MIC IP dynamic 7000 HD MIC-71xx, MIC-72xx Operation Manual...
-
Page 3: Table Of Contents
Device manager 7.1.2 Recording media 7.1.3 Activating and configuring storage media 7.1.4 Formatting storage media 7.1.5 Deactivating storage media Recording Profiles Maximum Retention Time Recording Scheduler Recording Status Alarm Alarm Connections Bosch Security Systems Operation Manual 2016.02 | 4.0 |... - Page 4 Controlling playback Operation 13.1 Using Intelligent Tracking 13.2 Recommended Use of Your MIC Camera 13.3 Using the Wiper/Washer (Bosch Protocol) 13.4 Using the Wiper/Washer (Pelco Protocol) 13.5 Configuring Settings for IR Illumination 13.6 Uploading a User Logo 2016.02 | 4.0 |...
-
Page 5: Table Of Contents | En
MIC IP starlight 7000 HD, MIC IP Table of Contents | en dynamic 7000 HD 13.7 Two-line and Three-line Camera Titles 13.8 Azimuth, Elevation, and Compass Directions Bosch Security Systems Operation Manual 2016.02 | 4.0 |... -
Page 6: Configuration Prerequisites
Click Set and Reboot. The camera will reset (go through the homing sequence, which usually takes 30 seconds to complete), and then the Live page appears, with updated video and the new IP address. 2016.02 | 4.0 | Operation Manual Bosch Security Systems... -
Page 7: System Overview
1 hour without power if no central time server is selected. Live page The LIVE page is used to display the live video stream and control the unit. Bosch Security Systems Operation Manual 2016.02 | 4.0 |... -
Page 8: Configuration
| Configuration dynamic 7000 HD Configuration Configuring Audio (Optional) Note for MIC7000 cameras only: These options are available only if you have connected a VIDEOJET connect device (VJC-7000-90) to your camera. 2016.02 | 4.0 | Operation Manual Bosch Security Systems... -
Page 9: General
BVC or Bosch Video Management Systems Programs. Enter a unique, unambiguous name for the camera in this field. You can use both lines for this. -
Page 10: Date/Time
Click the Generate button to generate data from the database in the unit and enter it into the table. Make changes by clicking an entry in the table. The entry is selected. Clicking the Delete button will remove the entry from the table. 2016.02 | 4.0 | Operation Manual Bosch Security Systems... -
Page 11: Display Stamping
If necessary, you can also display milliseconds. This information can be useful for recorded video images; however, it does increase the processor's computing time. Select Off if you do not need to display milliseconds. Bosch Security Systems Operation Manual 2016.02 | 4.0 |... -
Page 12: Gb/T 28181
GB/T 28181 national standard. H.264 elementary stream Select this checkbox to select or to enable the H.264 elementary stream. Registration timeout Enter a value (in milliseconds) for the registration timeout. The default is 3600. 2016.02 | 4.0 | Operation Manual Bosch Security Systems... - Page 13 Enter the ID of the device. Device port Enter the number of the device port. The default is 5060. Password Enter the appropriate password. Alarm device ID Enter the ID of the alarm device. Bosch Security Systems Operation Manual 2016.02 | 4.0 |...
-
Page 14: Web Interface
You can specify the interval at which the individual images should be generated for the M- JPEG image on the LIVE page. JPEG quality You can specify the quality at which the JPEG images appear on the LIVE page. 2016.02 | 4.0 | Operation Manual Bosch Security Systems... -
Page 15: Live Functions
Here you can specify whether the LIVE page displays the Special Functions section. Path for JPEG and video files Enter the path for the storage location of individual images and video sequences that you can save from the LIVE page. Bosch Security Systems Operation Manual 2016.02 | 4.0 |... - Page 16 7000 HD If necessary, click Browse to find a suitable directory. Video file format Select a file format for the live page display. The MP4 format does not include metadata. 2016.02 | 4.0 | Operation Manual Bosch Security Systems...
-
Page 17: Camera
Click the Reboot button to reboot the camera. There is a ten (10) second pause before the camera starts its homing phase. During the homing phase, the camera will complete finding the upper and lower tilt limits. Bosch Security Systems Operation Manual 2016.02 | 4.0 |... -
Page 18: Encoder Profile
SD Bit Rate Optimized For an SD image, the video bit rate and frame quality are adjusted to ensure that the bit rate is the priority. 2016.02 | 4.0 | Operation Manual Bosch Security Systems... - Page 19 P-frames, and thus the maximum achievable quality of the P- frames. In the H.264-protocol, the Quantization Parameter (QP) specifies the degree of compression and thus the image quality for every frame. The lower the quantization of the P- Bosch Security Systems Operation Manual 2016.02 | 4.0 |...
-
Page 20: Encoder Streams
Note: In order to select the option “H.264 MP 720p50/60 fixed” here, you must first set the field Max. frame rate in Camera > Installer Menu to “50/60 fps (up to 1280 x 720 px).” 2016.02 | 4.0 | Operation Manual Bosch Security Systems... - Page 21 SD Bit Rate Optimized For an SD image, the video bit rate and frame quality are adjusted to ensure that the bit rate is the priority. Bosch Security Systems Operation Manual 2016.02 | 4.0 |...
-
Page 22: Encoder Regions
Note: If you have not yet defined any prepositions/scenes, refer to Prepositions and Tours. If required, select another region and repeat the steps. To remove a region, select the area and click the waste bin icon. Click Set to apply the region settings. 2016.02 | 4.0 | Operation Manual Bosch Security Systems... -
Page 23: Privacy Masks
Inverted. Refer to Installer Menu for orientation settings. Notice! When MIC is canted, Privacy Masks should not be created for scene objects less than 2 m (6 feet) distance from camera. Bosch Security Systems Operation Manual 2016.02 | 4.0 |... -
Page 24: Picture Settings
The degree of color in the video image (HD only). Values range from -14° to 14°; the default is 8°. Select On to activate intelligent Dynamic Noise Reduction (DNR) which reduces noise based on motion and light levels. Gain control Adjusts the automatic gain control (AGC). 2016.02 | 4.0 | Operation Manual Bosch Security Systems... - Page 25 – On - Stabilization is always on. – Off - Stabilization is disabled. – Auto - Stabilization activates automatically when the camera detects vibration greater than the set threshold. Bosch Security Systems Operation Manual 2016.02 | 4.0 |...
-
Page 26: Lens Settings
For tours, save presets using One Push (“Spot Focus“). Focus speed Use the slider (from 1 to 8) to control how fast the Auto focus will readjust when the focus becomes blurred. 2016.02 | 4.0 | Operation Manual Bosch Security Systems... -
Page 27: Ptz Settings
Select On to freeze the image while the camera moves to a predetermined scene position. Max. PT speed [%] Sets the maximum pan/tilt speed (in percent). Settings range from 1 to 100. The default is 100. Bosch Security Systems Operation Manual 2016.02 | 4.0 |... - Page 28 Determine the North compass heading, then move the camera to that position. Select the radio button On for the parameter Compass. Click the button next to North point to set the calibration point. 2016.02 | 4.0 | Operation Manual Bosch Security Systems...
-
Page 29: Prepositions And Tours
Select the appropriate function from the drop-down list. Function Description Start auto pan Start auto pan with limit Stop auto pan Start custom tour Stop custom tour Start tour Stop tour Bosch Security Systems Operation Manual 2016.02 | 4.0 |... - Page 30 IR focus correction off OSD feedback on OSD feedback off IR mode on IR mode off IR mode auto Visible light on Visible light off Visible light inhibit on Visible light inhibit off 2016.02 | 4.0 | Operation Manual Bosch Security Systems...
-
Page 31: Sectors
Select the percentage of intensity of the infrared (IR) light. No white light Select On to disable the white light illuminators. The options in the field White light illuminators are disabled. Select Off to enable white light illuminators. Bosch Security Systems Operation Manual 2016.02 | 4.0 |... -
Page 32: Audio
6.16 Pelco AUX map Pelco controller keyboards (that support Pelco protocols D and P) support 8 different auxiliaries (AUX On/OFF commands), but do not define what function each AUX should perform. 2016.02 | 4.0 | Operation Manual Bosch Security Systems... - Page 33 IR mode Night mode Night mode auto Alarm output 1 Alarm output 2 Alarm output 3 Alarm output 4 White light Intelligent defog Intelligent tracking Serial mode Select Simplex or Full-duplex. Bosch Security Systems Operation Manual 2016.02 | 4.0 |...
-
Page 34: Recording
It is also possible to let the VRM Video Recording Manager control all recording with accessing an iSCSI system. This is an external program for configuring recording tasks for video servers. For further information please contact your local customer service at Bosch Security Systems Inc. -
Page 35: Formatting Storage Media
Including metadata could make subsequent searches of recordings easier but it requires additional memory capacity. Caution! Without metadata, it is not possible to include video content analysis in recordings. Bosch Security Systems Operation Manual 2016.02 | 4.0 |... -
Page 36: Maximum Retention Time
Notice! For more information, please see the Alarm Task Script Language document and the RCP+ documentation. For the latest version of these documents access your Bosch product catalog on the Internet. Export to account Select this parameter if you want all alarm recordings to be exported to an FTP server automatically. -
Page 37: Recording Scheduler
You can stop the recording activity at any time and modify the settings. Click the Start button to activate the recording scheduler. Click the Stop button to deactivate the recording scheduler. Running recordings are interrupted and the configuration can be changed. Bosch Security Systems Operation Manual 2016.02 | 4.0 |... -
Page 38: Recording Status
The graphic indicates the recording activity of the camera. You will see an animated graphic while recording is taking place. Recording Status Details of the recording status are displayed here for information. These settings cannot be changed. 2016.02 | 4.0 | Operation Manual Bosch Security Systems... -
Page 39: Alarm
VIDOS or Bosch Video Management System, you can store a general password here. The camera can use this general password to connect to all remote stations protected with the same password. - Page 40 IP addresses after each reboot, after a connection breakdown or after a network failure. Notice! In the default setting, Stream 2 is transmitted for automatic connections. Bear this fact in mind when assigning the profile (see Encoder Profile). 2016.02 | 4.0 | Operation Manual Bosch Security Systems...
-
Page 41: Vca
If you select the option Silent VCA, then the system creates metadata to facilitate searches of recordings but no alarm is triggered. You cannot change any parameters for this configuration. If you want to turn off VCA, then select Off. Preset Select Off or Test. Bosch Security Systems Operation Manual 2016.02 | 4.0 |... - Page 42 Notice! Additional analysis algorithms with comprehensive functions such as IVMD and IVA are available from Bosch Security Systems Inc. If you select one of these algorithms, you can set the corresponding parameters here directly. You can find information on this in the relevant documents on the product CD supplied.
- Page 43 Global change Activate this function if the global change, as set with the Global change slide control, should trigger an alarm. Bosch Security Systems Operation Manual 2016.02 | 4.0 |...
- Page 44 Right-click any fields you wish to deactivate. Click OK to save the configuration. Click the close button X in the window title bar to close the window without saving the changes. 2016.02 | 4.0 | Operation Manual Bosch Security Systems...
-
Page 45: Virtual Masks
In this case, the camera automatically sends an e-mail to a previously defined e-mail address. Bosch Security Systems Operation Manual 2016.02 | 4.0 |... -
Page 46: Alarm Task Editor
As an alternative to the alarm settings on the various alarm pages, you can enter your desired alarm functions in script form here. This will overwrite all settings and entries on the other alarm pages. 2016.02 | 4.0 | Operation Manual Bosch Security Systems... -
Page 47: Alarm Rules
17 is set to either of the following values: ) – ”[camera name] - IO“ (for a camera connected to MIC-ALM-WAS-24) – “[camera name] – VJC-7000” (for a camera connected to VJC-7000-90) Bosch Security Systems Operation Manual 2016.02 | 4.0 |... -
Page 48: Interfaces
Bistable. If you wish an alarm-activated siren to sound for ten seconds, for example, select 10 s. Output name Enter a name for the alarm output. Toggle Click the button to test the relay / output connection. 2016.02 | 4.0 | Operation Manual Bosch Security Systems... -
Page 49: Network
If a DHCP server is employed in the network for the dynamic assignment of IP addresses, you can activate acceptance of IP addresses automatically assigned to the camera. Certain applications (Bosch Video Management System, Archive Player, Configuration Manager) use the IP address for the unique assignment of the unit. If you use these... - Page 50 You can set the maximum segment size for the IP packet's user data. This gives you the option to adjust the size of the data packets to the network environment and to optimize data transmission. Please comply with the MTU value of 1,514 bytes in UDP mode. 2016.02 | 4.0 | Operation Manual Bosch Security Systems...
-
Page 51: Dyndns
RTSP port If necessary, select a different port for the exchange of the RTSP data from the list. The standard RTSP port is 554. Select Off to deactivate the RTSP function. Bosch Security Systems Operation Manual 2016.02 | 4.0 |... -
Page 52: Network Management
For example, access to the unit can then be made using Windows Explorer without knowledge of the IP address of the unit. 2016.02 | 4.0 | Operation Manual Bosch Security Systems... -
Page 53: Multicast
To do this, check the box. You can then enter the multicast address. Multicast Address Enter a valid multicast address for each stream to be operated in multicast mode (duplication of the data streams in the network). Bosch Security Systems Operation Manual 2016.02 | 4.0 |... -
Page 54: Image Posting
Select the target—the name of the account on the server—to which to save images. When face recognition is available, selected images of the face can be sent to a target account. 2016.02 | 4.0 | Operation Manual Bosch Security Systems... -
Page 55: Accounts
IP Address 1 / 2 Enter the IPv4 address that you want to allow or block Mask 1 / 2 Enter the subnet mask for the appropriate IPv4 address. Bosch Security Systems Operation Manual 2016.02 | 4.0 |... -
Page 56: Service
This window is for the activation of additional functions by entering activation codes. An overview of installed licenses is shown. The installation code of the unit is also displayed here. 11.3 Certificates Usage list HTTPS server Select the default certificate for the HTTPS server. 2016.02 | 4.0 | Operation Manual Bosch Security Systems... -
Page 57: Diagnostics
This window is for information only and cannot be modified. Keep this information at hand when seeking technical support. Select the text on this page with a mouse and copy it so that it can be pasted into an e-mail if required. Bosch Security Systems Operation Manual 2016.02 | 4.0 |... -
Page 58: Operation Via The Browser
Note: If the preposition is already stored, a dialog box displays the message, “Overwrite current preposition?” Click OK to overwrite, or click Cancel to cancel the operation. Click to display the selected preposition in the video image. 2016.02 | 4.0 | Operation Manual Bosch Security Systems... -
Page 59: Aux Control
12.1.6 Saving snapshots Individual images from the displayed live video stream can be saved locally in JPEG format on the computer's hard drive. Bosch Security Systems Operation Manual 2016.02 | 4.0 |... -
Page 60: Recording Live Video
– if the CPU load is too big, change the VCA settings, – if the network load is too big, change the encoder profile to reduce bitrate. 2016.02 | 4.0 | Operation Manual Bosch Security Systems... -
Page 61: Status Icons
Select an option from the drop-down box to define a search parameter. Click Start Search. The results are shown. Click a result to play it back. Click Back to define a new search. Bosch Security Systems Operation Manual 2016.02 | 4.0 |... -
Page 62: Exporting Recorded Video
Select the playback speed using the speed regulator – Jump to start of active sequence or to previous sequence – Jump to start of the next video sequence in the list 2016.02 | 4.0 | Operation Manual Bosch Security Systems... -
Page 63: Operation
Avoid motion that moves directly towards the camera. – Avoid locations that attract large numbers of people, such as retail stores or intersections. Intelligent Tracking is optimized for scenes with very few moving objects. – Unwanted Motion Bosch Security Systems Operation Manual 2016.02 | 4.0 |... - Page 64 Gray eye without a symbol Intelligent Tracking is idle, waiting to track a target. Gray eye with a “pause” Intelligent Tracking attempts to track a symbol target passively while a user has camera control. 2016.02 | 4.0 | Operation Manual Bosch Security Systems...
- Page 65 The camera will restart tracking if a target starts moving in the same area where the initial target stopped moving or if the camera detects an object moving along the last known trajectory. Bosch Security Systems Operation Manual 2016.02 | 4.0 |...
-
Page 66: Recommended Use Of Your Mic Camera
The tour should also include at least 10° of tilt movement. Preset Tours For scenarios that require the camera to be in continuous motion for most of the day, Bosch recommends that you set the camera in Preset Tour mode, moving between a desired set of presets. -
Page 67: Using The Wiper/Washer (Bosch Protocol)
Operation | en dynamic 7000 HD 13.3 Using the Wiper/Washer (Bosch Protocol) The "predefined position" for the wash/wipe function is preset 62. The installer must define preset 62 (preferably where the washer nozzle is located and can direct washer fluid towards the camera window) before using the wiper/washer function. -
Page 68: Using The Wiper/Washer (Pelco Protocol)
If you prefer not to see this freeze frame, you can turn off the Freeze Frame on Preposition in the PTZ Setup menu. 2016.02 | 4.0 | Operation Manual Bosch Security Systems... -
Page 69: Configuring Settings For Ir Illumination
The file format must be a bitmap (.bmp). – Height and width must not exceed 128 pixels. – Color depth must be 8 bit (256 color bitmap). Upload the Logo File If necessary, open the browser. Click Configuration. Bosch Security Systems Operation Manual 2016.02 | 4.0 |... - Page 70 Day Mode. Toggle the text colors in the following sequence: White- >Yellow->Violet->Red->Cyan->Green->Blue->White. – Using the command AUX OFF-77-ENTER, users can set the color again to the default white. 2016.02 | 4.0 | Operation Manual Bosch Security Systems...
- Page 71 LOOKING will always appear in English and will be at a fixed location on the OSD. – The X or XX designates the compass direction that updates automatically as the camera pans. A identifies “North,” “South,” “East,” or West.” AA identifies “Northeast,” “Northwest,” “Southeast,” or “Southwest.” Bosch Security Systems Operation Manual 2016.02 | 4.0 |...
- Page 72 Azimuth Zero point. Notice! Bosch recommends that only the installer calibrate the Azimuth Zero point. A recalibration to the Azimuth Zero point may cause inaccurate compass headings. Set the Azimuth Zero point: Determine the North compass heading, then move the camera to that position.
- Page 74 Bosch Security Systems, Inc. 1706 Hempstead Road Bosch Sicherheitssysteme GmbH Lancaster, PA, 17601 Robert-Bosch-Ring 5 85630 Grasbrunn www.boschsecurity.com Germany © Bosch Security Systems, Inc., 2016 www.boschsecurity.com...