Page 1
FORM NO. 3319–307 REV A ProLine Edger Model No. 53030 — 7900001 & Up 16” & 18” Gas Modèle No. 51903 — 790000001 et suivants Modèle No. 51904 — 790000001 et suivants Modèle No. 51906 — 790000001 et suivants Modèle No. 51907 — 790000001 et suivants 16”...
Page 2
WARNING: The engine exhaust from this product contains chemicals known to the State of California to cause cancer, birth defects, or other reproductive harm. AVERTISSEMENT: Les gaz d’échappement du moteur de ce produit contiennent des produits chimiques reconnus dans l’état de Californie comme cancérigènes, responsables de malformations congénitales, ou comme nocifs à...
Switch Wire 6. Clutch Drum Housing Français 13. Fuel Tank 7. Engine 14. Air Filter 8. Model and Serial Number Español Decal (on rear of engine stand) Français Español The Toro Company – 1996 Printed in USA All Rights Reserved...
Page 8
English 1. Gearcase 5. Blade Bolt (left-hand thread) 2. Splined Shaft 6. 3mm Hex Wrench English 3. Boss Adapter 7. Clamping Washer 1. Primer Bulb 2. Fuel Return Line 4. Edger Blade Français Français Español Español English 1. Starter Handle 2.
Page 9
English 1. Idle Speed Adjustment Screw Français English Español 1. Stop Switch 4. Throttle Trigger (in idle position) 2. Fast-idle Lock 3. Throttle Trigger (in fast-idle start position) Français Español...
Page 10
English English 1. Shield 4. Knob 1. Hearing Protection 6. Shield Adjusted to Clear 2. Increase the Depth of Cut 5. Wheel Blade, and Shield 2. Eye Protection Operator from Thrown 3. Decrease the Depth of 3. Right Arm Slightly Bent Debris 4.
Page 11
English 1. Air Filter Cover 3. Foam Ring 2. Filter Screen Français Español English 1. Filter Screen 3. Air Filter Cover 2. Cutout (typical) 4. Plastic Post (typical) Français Español...
Page 12
English 1. Wire 3. Fuel Filter 2. Fuel Pick-up Hose Français Español English 1. Socket Head Screw (5) 4. Spark Arrester 2. Tail 5. Muffler Cover 3. Gasket 6. Muffler Body Français Î Î Î Î Î Español Î Î Î Î Î Î...
Page 13
English 1. Drive Shaft Tube 4. #2 Lithium-base Bearing Lube 2. Flexible Drive Shaft 5. Phillips Hex Head 3. Gearhead Screw (2) Français Español...
......Power Edger Operating Safety ..All of us at Toro want you to be completely satisfied with your new product, so feel free to contact your Safety and Instruction Decals .
DANGER, WARNING and CAUTION are signal Always wear hearing protection. words used to identify the level of hazard. However, regardless of the hazard, be extremely careful. DANGER signals an extreme hazard that will cause serious injury or death if the recommended precautions are not followed.
Never use a cutting blade or replacement parts Drain the tank and run the engine dry before that are not approved by Toro. storing the unit. 10. Store fuel and Edger away from open flame, Maintain the Edger according to the sparks and excessive heat.
Safety and Instruction Decals Safety decals and instructions are easily visible to the operator and are located near any area of potential danger. Replace any decal that is damaged or lost. ON SHAFT (Part No. M221501) ON SHAFT (Part No. M221502) ON BLADE SHIELD (Part No.
Assembly Connecting Stop Switch Wires Install the plastic tube (packed with the drive shaft assembly) around the throttle cable and Assembling Engine and Drive stop switch wires (Fig. 7). Shaft Assembly Loosen the knob and remove the air cleaner cover to access the stop switch wires (Fig. 8). The drive shaft, clutch drum housing and gearcase are assembled.
Installing Shield Install the edger blade, clamping washer and blade bolt (Fig. 12). Note: The blade bolt has left-hand threads. Align the hole in the boss adapter with the hole POTENTIAL HAZARD in the gearcase (Fig. 12). Foreign objects can be thrown by Edger. Insert the 3mm hex wrench into the holes in the WHAT CAN HAPPEN boss adapter and gearcase to lock the splined...
Page 21
SUCH AS ETHANOL, METHANOL OR Only use a two-cycle engine oil formulated for use in ISOPROPYL. ADDITIVES SHOULD NOT high-performance, air-cooled two-cycle engines. Toro BE USED TO TRY TO ENHANCE THE brand 2-cycle oil is formulated for use in POWER OR PERFORMANCE OF high-performance, air-cooled two-cycle engines.
Edger fuel tank. For your fuel premix, only use a quality oil Always mix fuel and oil in a clean container designed for 2–cycle air cooled engines. Toro approved for gasoline. 50:1 2–Cycle Oil is formulated to meet the...
Cold Starting Procedure and move the stop switch to the “ON” position (Figs. 14 and 15). The carburetors on Toro engines contain a choke system. To start a “cold” engine properly, perform the Leave the throttle trigger in the idle position and following procedure: pull the starter handle (Figs.
Edger blade rotates or the engine shaft if necessary for a comfortable position stalls, stop using the Edger immediately! (Fig. 17). Contact your local authorized Toro Dealer for The Edger weight should be evenly distributed assistance and servicing. between the arms (Fig. 17).
Adjust the Edger to the correct cutting depth Rotating the shield to lower the wheel before you start the engine. (Refer to Setting decreases the depth of cut. Depth of Cut on page 11.) Make sure the shield Make sure the shield is positioned to protect the is adjusted to shield the operator from thrown operator from thrown debris, then tighten the debris (Figs.
Fuel Filter Spark Plug Maintenance With the engine at ambient (room) temperature, Maintenance Interval loosen the knob and remove the air cleaner cover (Fig. 8). The fuel filter should be replaced after every 100 hours of operation. Loosen the knob and lift off the cylinder cover (Fig.
Loosen the knob and lift off the cylinder cover Remove and clean the tail, gasket and spark (Fig. 8). arrester with a safety solvent and a stiff brush. If any part cannot be thoroughly cleaned, it must Clean all dirt and debris from the cooling fins be replaced.
Always turn off your Edger before you clean or perform any maintenance on it. Flexible Drive Shaft Lubrication The Toro Edger will provide maximum performance for many, many hours if it is maintained properly. Good maintenance includes regular checking of all...
Tighten throttle wire Engine Lacks Power or Stalls When Cutting Cutting Dirty air filter Clean or replace air filter If further assistance is required, contact your local authorized Toro service dealer. Specifications Engine Displacement 26cc Blade Type 8” spring steel...
Also included may be hoses, belts, connectors and other emission–related assemblies. Where a warrantable condition exists, Toro will repair your lawn and garden equipment engine at no cost to you including diagnosis, parts and labor.
Page 31
In order to file a claim, go to your nearest Authorized Toro Service Dealer. Warranty services or repairs will be provided at all Authorized Toro Service Dealers.
Page 32
Pickup and delivery charges for distances beyond a 15-mile radius from a TORO ProLine Service Dealer. TORO Products used for residential use are covered by a full two-year warranty. All repairs covered by this warranty must be performed by a TORO Service Dealer using Toro approved replacement parts.