Miele W 6071 Operating Instructions Manual
Hide thumbs
Also See for W 6071:
- Operating instructions manual (38 pages) ,
- Operating and installation instructions (44 pages)
Related Manuals for Miele W 6071
Summary of Contents for Miele W 6071
- Page 1 Operating Instructions Wet Clean System W 6071 To prevent accidents and machine damage read these instructions before installation or use. M.-Nr. 06 018 400...
-
Page 3: Table Of Contents
Contents IMPORTANT SAFETY INSTRUCTIONS ......... . . 4 Guide to the washer . -
Page 4: Important Safety Instructions
As a safety feature the door handle has been designed with a Installation, repair and maintenance work break line. should be by a Miele authorized service technician. Work by unqualified persons Never allow children to play in, on or could be dangerous. - Page 5 Miele spare parts. may become void. The safety standards of the machine can Chlorine or agents containing chlorine only be guaranteed when Miele spare parts are corrosive, and can under certain are used. conditions lead to permanent damage to Over time deterioration of parts can components.
-
Page 6: Guide To The Washer
Guide to the washer Front view 1 Detergent dispenser 2 Control panel 3 Drum door 4 Outer casing 5 Drain pump door 6 4 Height adjustable feet... - Page 7 4 Drain (for drain valve)* 10 Printer Interface 5 Back panel 11 Cable connection for 6 Liquid dispenser drawer 3 dispenser pumps Liquid dispensing system 12 Cable connection for the liquid * not available in W 6071 dispensing system...
- Page 8 Guide to the washer Facia panel Display Cursor and input buttons Program selector Delay Start button X Start Door open Y Power on button 7 End 10 Z Power off button Optic interface 11 Access lock 12 Special options buttons...
- Page 9 Guide to the washer Display The display content will appear once the machine is turned on. It is up to four lines and 40 digits long, showing which program has been selected. Display during a program 1 Planned temperature for the current cycle 2 Name of the current cycle 3 Program number 4 Program name...
- Page 10 Guide to the washer Program selector Standard programs: Selector Selector Position Program Position Program Colored Sensitive Shirts Starch Regular Only WC Silks/ Leather Rayons Sensitive Machine Leather Wash Regular High Program numbers 1 - 24 can be selected Machine directly. Program numbers 25 - 99 can be Wash Proofing selected using selector position 24 and the...
- Page 11 Guide to the washer Access lock Access keys Key 1 (2 supplied) for operating levels A and B. Programs which have been allocated free Key 2 for operating levels A, B, C. access can be run. See Programming Instructions for allocation Key 3 for operating levels A, B, C, D.
- Page 12 Guide to the washer Buttons Special options T Prewash with indicator X Start A Prewash cycle is added to the program. Press this button to start the selected program. U Starch with indicator 7 End Press this button for starched laundry. Press this button to stop a program.
- Page 13 Guide to the washer Cursor, input and Delay Start buttons Optical interface Data transfer to and from the machine’s controls and a PC can take place using the proper software. The optic interface 9 on the machine’s control panel provides the connection point.
-
Page 14: Before Using The Washer
Before using the washer Setting current time and date If pauses between programming steps ^ Turn off the machine with the Z "Power off" lasts longer than 25 seconds, the display button. will return to the basic stage and the ^ Turn the key to position B "Operation". -
Page 15: Operation
Pepare and sort the laundry Important: This machine must be properly installed before using. The first run of the washer must be performed by a Miele authorized service technician. ^ Open the water valves to the washer. ^ Turn the main power on at the wall switch. -
Page 16: Load The Laundry
Operation Load the laundry Maximum load size (dry) 16.5 lbs (7,5 kg). Additional load size information for each program are available in the "Programming Instructions". ^ Load the laundry into the drum. For best results, wash mixed loads of small and large items. -
Page 17: Select A Program
Operation Select a program ^ Turn the access key to position B "Operation". ^ Use the T "Prewash" button to select a "Prewash" if required. The indicator above the T button will light. ^ Press the Y "Power on" button. When "Prewash"... -
Page 18: Add Detergent
Operation Add detergent Water hardness Water Water Hardness grains per hard- quality level in gallon ness mmol/l levels soft 0 - 1.3 0 - 7 middle 1.3 - 2.5 7 - 14 hard 2.5 - 3.8 14 - 21 very over 3.8 over 21 hard... -
Page 19: Changing Temperaure And Spin Speed
Operation Changing temperaure and spin Program sequence display speed The program sequence is shown in the display after the start of the program. The following parameters can be changed before the start of a program: PROGRAMME COTTONS – the temperature in 1 °C steps from cold, 20 °C ^^^^^^^^ 60°... -
Page 20: Program End - Opening The Drum Door
Operation Program end - opening the drum If this was the last load of wash for the day, or longer: door ^ Leave the drum door open. At the end of the program, with a stationary drum and no more water in the machine the ^ Turn off the machine. -
Page 21: Special Options
Special options Prewash Starch Select a Prewash for heavily soiled laundry. Starch can be added before the program The prewash can selected by pressing the begins by pressing the U "Starch" button. T "Prewash" button. The Prewash indicator The indicator above the button will light. above the button will light. -
Page 22: Without Final Spin
Special options Without final spin Rinsing with hot water Standard programs 10 Cottons 200 °F (95°C) and 11 Cottons 140 °F (60°C) are programmed to rinse with hot water. If a hot water supply is available it is an ad- vantage to run the final rinse with hot water. -
Page 23: Skipping Program Cycles
Special options Skipping program cycles Cancelling a program To cancel a program, press 7 "End" twice. Cycles of a program in progress can be skipped or repeated. If the program is interrupted during a cycle, Press the 7 "End" button to stop the the following display messages will appear: program. -
Page 24: Delay Start
Special options Delay start Use the W "Delay start" button to program the unit to start automatically at a later time. ^ Turn the key to position B "Operation". ^ Turn on the machine and select a program with the program selector. The display shows the following (example): ^ Press X "Start"... - Page 25 PC-Operation: Program changes can be made via a PC, or a new program can be downloaded. This requires a special Editor Program which is available from the Miele Professional Department. Printer-Operation: It is possible to print out whole programs or parts of programs.
-
Page 26: Washer Care
^ Wipe away any deposits from the drum door seal with a damp cloth. ^ Clean the drum with a stainless steel cleaner specially formulated for use in a washer, available from Miele’s Technical Service Department Part # 00 077 927. ^ Open the lint trap door. - Page 27 Washer care ^ Place a 2 qt (2 l) capacity container under the drain tube. ^ Check that the drain pump impeller (in the back of the chamber) rotates freely by ^ Turn the lint trap lid counterclockwise 2- 3 spinning with your hand.
-
Page 28: Cleaning The Water Inlet Filters
The hose must be replaced if there are small cracks in the surface or if it has been damaged or cut. Only use hose that can withsatnd a minimum pressure of 70 bar. Original Miele hoses fulfill this requirement. -
Page 29: Cleaning The Detergent Drawer
Washer care Cleaning the detergent drawer ^ The detergent dispenser should be cleaned after each use to remove any detergent residue. ^ The siphon tubes in the § and y compart- ments should also be cleaned. ^ Unscrew the siphon tubes. ^ Clean the siphon tubes with warm water. -
Page 30: Frequently Asked Questions
Frequently asked questions Power failure Emergency door release during a prolonged power failure During a short power failure ,Make sure the machine is off and the The program remains in the last position. drum has stopped turning. A moving When power is restored the following drum is dangerous. -
Page 31: Fault Messages
HEATING SYSTEM FAULT ce with local and national safety regula- tions. Unauthorized repairs could cause an injury or machine damage. ^ Call the Miele Service Department. Faults that occur before or after the start of a PROGRAMME 11 COTTONS program flash in the display. - Page 32 Use a low sudsing detergent or contact Oversudsing detergent Miele’s application specialists. Very soft water In areas with soft water, use less detergent. Soiling level of laundry For lightly soiled laundry use less detergent.
-
Page 33: Technical Service
(Fabr.-Nr.) of the machine. These can be found on the silver data plate: by opening the drum door, or: on the back panel of the machine. Only use original Miele spare parts when performing maintenance or repairs on this machine. -
Page 34: Guide To The Data Plate Symbols
8 Drum diameter/ drum depth 19 Gas heating* 9 Spin speed 20 Commissioning date 10 Drum volume/ Laundry dry weight 21 Water-registration DVGW-test cert 11 Kinetic Energy 22 Field for CE test symbol/ (Product ID-No./Gas) * does not apply to W 6071... -
Page 35: Installation Instructions
INSTALLATION INSTRUCTIONS To prevent accidents and machine damage read these instructions before installation or use. -
Page 36: Installation Instructions
Installation Instructions Shipping struts The washer must only be installed a Miele Once the machine is in its final position the authorized service technician. red-marked shipping struts "A", "B" and "C" must be removed. Installation Save the shipping struts for future use. They must be refitted if the machine is moved. -
Page 37: Level The Washer
Installation Instructions Removing the rear shipping struts Level the washer To remove the rear shipping struts, unscrew The machine must be level to ensure proper the 3 SW 13 screws and loosen the 15 lower operation. torx screws from the back panel. “B”... -
Page 38: Plumbing
This work must be carried out by a Miele Possible connections: authorized service technician. ^ Directly into a sink Water will drain into the... -
Page 39: Electrical Connection
Electrical Connection Electrical connection All electrical work must be performed by a qualified technician in accordance with applicable codes and standards. The machine must only be connected to the voltage and frequency shown on the data plate. The machine is supplied as standard for connection to a 208 V, 60 Hz, 3 X 20 A, three-phase electricity supply. - Page 40 Alterations rights reserved /000/1903 This bio-friendly paper was bleached without the use of chlorine.