Toro 02720 Operator's Manual
Toro 02720 Operator's Manual

Toro 02720 Operator's Manual

36in (92cm) mid-size flail attachment
Hide thumbs Also See for 02720:

Advertisement

Quick Links

Form No. 3367-853 Rev C
36in (92cm) Mid-Size Flail
Attachment
Model No. 02720—Serial No. 312000001 and Up
To register your product or download an Operator's Manual or Parts Catalog at no charge, go to www.Toro.com.
Original Instructions (EN)

Advertisement

Table of Contents
loading

Summary of Contents for Toro 02720

  • Page 1 Form No. 3367-853 Rev C 36in (92cm) Mid-Size Flail Attachment Model No. 02720—Serial No. 312000001 and Up To register your product or download an Operator's Manual or Parts Catalog at no charge, go to www.Toro.com. Original Instructions (EN)
  • Page 2: Table Of Contents

    Replacing the Gearbox Drive Belt ......8 additional information, contact an Authorized Service Replacing the Rotor Drive Belt......9 Dealer or Toro Customer Service and have the model Checking the Gearbox Oil Level ......9 and serial numbers of your product ready. The model Storage...............
  • Page 3: Safety

    Operator’s Manual, which have been found necessary as a result of the research and testing of the Toro company. This cutting flail attachment is capable of amputating hands and feet and throwing objects. Failure to observe the safety instructions could result in serious injury or death.
  • Page 4: Product Overview

    A selection of Toro approved attachments and accessories are available for use with the machine to enhance and expand its capabilities. Contact your Authorized Service Dealer or Distributor or go to www.Toro.com for a list of all approved attachments and accessories. Figure 2 1. Turnbuckle lock...
  • Page 5: Adjusting The Anti-Scalp Skids

    3. Turn the turnbuckle clockwise to lower the height of cut and counterclockwise to raise it until you reach the desired setting on the height-of-cut gauge (Figure 2). Height-of-cut Position Height of Cut (mm) (Height in Inches) 13 mm 25 mm 38 mm 1-1/2 51 mm...
  • Page 6: Maintenance

    Maintenance Note: Determine the left and right sides of the machine from the normal operating position. Recommended Maintenance Schedule(s) Maintenance Service Maintenance Procedure Interval • Inspect the blades for wear or damage. • Clean under the guards. Before each use or daily •...
  • Page 7: Maintaining The Blades

    Maintaining the Blades Inspecting the Blades Service Interval: Before each use or daily Check the blades for wear or damage paying particular attention to the cutting edge, curved area, and installation hole (Figure 5). If the blade is excessively worn or damaged replace the blade.
  • Page 8: Checking The Rubber Discharge Guards

    Checking the Rubber Replacing the Gearbox Drive Discharge Guards Belt Service Interval: Before each use or daily Service Interval: Every 50 hours—Check the gearbox drive belt for wear or damage. Inspect the rear and the front rubber guards for wear or damage (Figure 8).
  • Page 9: Replacing The Rotor Drive Belt

    Replacing the Rotor Drive Belt B. Rotate the turnbuckle. Increase the length between the eyebolts to add more tension into Service Interval: Every 50 hours—Check the rotor the belt or decrease the length to decrease the drive belt for wear or damage. tension in the belt.
  • Page 10: Storage

    Storage Refer to the traction unit Operator’s Manual for details of machine storage.
  • Page 11 Spypros Stavrinides Limited Cyprus 357 22 434131 Surge Systems India Limited India 91 1 292299901 T-Markt Logistics Ltd. Hungary 36 26 525 500 Toro Australia Australia 61 3 9580 7355 Toro Europe BVBA Belgium 32 14 562 960 374-0269 Rev B...
  • Page 12 Countries Other than the United States or Canada Customers should contact their Toro Distributor (Dealer) to obtain guarantee policies for your country, province, or state. If for any reason you are dissatisfied with your Distributor's service or have difficulty obtaining guarantee information, contact the Toro importer. If all other remedies fail, you may contact us at Toro Warranty Company.

Table of Contents