Elkay LZWSRK -EZH2O Installation, Care & Use Manual
  1. Manuals
  2. Brands
  3. Elkay Manuals
  4. Water Dispenser
  5. LZWSRK -EZH2O
  6. Installation, care & use manual
Elkay LZWSRK -EZH2O Installation, Care & Use Manual

Elkay LZWSRK -EZH2O Installation, Care & Use Manual

Retro-fit bottle filling unit
Hide thumbs Also See for LZWSRK -EZH2O:

Advertisement

Table of Contents

LZWSRK -EZH2O
IMPORTANT! INSTALLER PLEASE NOTE.
THE GROUNDING OF ELECTRICAL EQUIPMENT SUCH AS TELEPHONE, COMPUTERS, ETC. TO WATER LINES
IS A COMMON PROCEDURE. THIS GROUNDING MAY BE IN THE BUILDING OR MAY OCCUR AWAY FROM THE
BUILDING. THIS GROUNDING CAN CAUSE ELECTRICAL FEEDBACK INTO A FOUNTAIN, CREATING AN ELEC-
TROLYSIS WHICH CAUSES A METALLIC TASTE OR AN INCREASE IN THE METAL CONTENT OF THE WATER.
THIS CONDITION IS AVOIDABLE BY USING THE PROPER MATERIALS AS INDICATED. ANY DRAIN FITTINGS
PROVIDED BY THE INSTALLER SHOULD BE MADE OF PLASTIC TO ELECTRICALLY ISOLATE THE FOUNTAIN
FROM THE BUILDING PLUMBING SYSTEM. WE SUGGEST THAT THE BOTTLE FILLING STATION AND WATER
COOLER BE PROTECTED BY A GROUND FAULT CIRCUIT INTERRUPTER (GFCI).
INSTALLER
LZWSR Bottle Fillers are among the easiest to install on the market today. To
insure you install these models easily and correctly, PLEASE READ THESE
SIMPLE INSTRUCTIONS BEFORE STARTING THE INSTALLATION. CHECK
YOUR INSTALLATION FOR COMPLIANCE WITH PLUMBING, ELECTRICAL, AND
OTHER APPLICABLE CODES. After installation, leave these instructions with the
Fountain for future reference.
LZWSR*1A
INSTALLATION, CARE & USE MANUAL
T M
R
-F
B
ETRO
IT
OTTLE
THIS IS AN INDOOR APPLICATION ONLY.
ALL SERVICE TO BE PERFORMED BY AN
AUTHORIZED SERVICE PERSON.
TOOLS REQUIRED
BUT NOT PROVIDED:
SAFETY GLASSES
GLOVES
1-3/8" HOLE PUNCH (PROVIDED)
1/2" DRILL BIT
ELECTRIC DRILL
3/4" WRENCH OR CRECENT WRENCH
5/16" NUT DRIVER
UTILITY KNIFE
TAPE MEASURE
PENCIL
CENTER PUNCH
1/2" SOCKET & RATCHET WRENCH
5/32" ALLEN WRENCH
Page 1
F
U
ILLING
NIT
IMPORTANT
98518C (Rev. B - 2/10)

Advertisement

Table of Contents
loading

Related Manuals for Elkay LZWSRK -EZH2O

Summary of Contents for Elkay LZWSRK -EZH2O

  • Page 1 LZWSR*1A INSTALLATION, CARE & USE MANUAL LZWSRK -EZH2O ETRO OTTLE ILLING IMPORTANT THIS IS AN INDOOR APPLICATION ONLY. ALL SERVICE TO BE PERFORMED BY AN AUTHORIZED SERVICE PERSON. TOOLS REQUIRED BUT NOT PROVIDED: SAFETY GLASSES GLOVES 1-3/8” HOLE PUNCH (PROVIDED) 1/2”...

  • Page 2: Water Cooler Preparation

    LZWSR*1A WATER COOLER PREPARATION 1) Remove lower front panel of watercooler by removing the four (4) screws from the bottom of cooler. (See FIG. 1) NOTE: For Two Level Models the Bottle Filling Unit should be mounted to the higher unit. Both lower front panels and basin assemblies will need to be removed.

  • Page 3: Basin Assembly Preparation

    LZWSR*1A BASIN ASSEMBLY FILTER ASSEMBLY SCREWS SCREWS SCREWS EWF3000 Filter Location Basin Assembly Removal Fig. 4 Fig. 3 BASIN ASSEMBLY PREPARATION 1) Center punch 1/2” hole location on basin prior to drilling the hole in top of cooler basin using an adequete drill and 1/2” drill bit capable of drilling through stainless steel (See FIG.

  • Page 4: Filter Installation

    LZWSR*1A 3/8” Water Inlet Solenoid Valve Water Inlet Filter Assembly Bubbler 1/4” Union Evaporator 3/8” Water Line from Bottle Filling Unit Evaporator Bubbler 1/4” Tee EZ Non-Pressurized 3/8” To 1/4” Union Plumbing Diagram Fig. 7 Solenoid Valve EZ Plumbing Diagram after Filter Installation &...

  • Page 5: Bottle Filler Installation

    LZWSR*1A MOUNTING 7/16” BOLT HOLES FOR SCREWS TOP COVER FASTENING UNIT TO WALL UNIT CENTER LINE Fig. 10 Fig. 9 BOTTLE FILLING UNIT WALL MOUNTING PLATE Fig. 11 BOTTLE FILLER INSTALLATION 1) Remove two (2) mounting screws with 5/32” allen wrench holding top cover to Bottle Filler (See FIG. 10). Remove top cover. Note do not discard mounting screws, they will be needed to reinstall top cover..

  • Page 6: Changing Filter/Resetting Visual Filter Monitor

    LZWSR*1A CHANGING THE FILTER AND RESETTING THE VISUAL FILTER MONITOR The electronic sensor includes LED filter status indicators that are factory preset to monitor filter life. The sensor monitors the “ON” time of the water valve solenoid and keeps track of total time water is dispensed. There are (3) LED’s that indicate the following: Green: LED (Good) indicates that the filter is operating within 0% - 80% of its life.

  • Page 7: Alternate Filter Mounting Location

    LZWSR*1A 1-3/8” Dia. Hole EXISTING HOLES 2.25 3/16” Dia. Hole Bottom View of Cooler Fig. 12 SCREWS PLASTIC BUSHING SCREWS FILTER MOUNTING BRACKET FILTER ASSEMBLY 3/8” WATER INLET Alternate Filter Mounting Location Fig. 13 ALTERNATE FILTER MOUNTING LOCATION 1) Using the supplied punch from the Bottle Filler installation, punch a 1-3/8” dia. hole “A” at the existing hole shown in Fig.

  • Page 8: Parts List/Kits

    PARA PIEZAS, CONTACTE A SU DISTRIBUIDOR LOCAL O LLAME AL 1.800.323.0620 IMPRIMÉ AUX É.-U. POUR OBTENIR DES PIÈCES, CONTACTEZ VOTRE DISTRIBUTEUR LOCAL OU COMPOSEZ LE 1.800.323.0620 ELKAY MANUFACTURING COMPANY • 2222 CAMDEN COURT • OAK BROOK, IL 60523 • 630.574.8484 98518C (Rev. B - 2/10) Page 8...

Table of Contents