Related Manuals for Comtrend Corporation CT-5365
Summary of Contents for Comtrend Corporation CT-5365
-
Page 1: Quick Start Guide
CT-5365 ADSL2+ Wireless Router Quick start Guide Version Eng-0, July 14, 2009 260094-002... - Page 2 Copyright Copyright©2009 Comtrend Corporation. All rights reserved. The information contained herein is proprietary to Comtrend Corporation. No part of this document may be translated, transcribed, reproduced, in any form, or by any means without prior written consent of Comtrend Corporation.
- Page 3 Protect Our Environment This symbol indicates that when the equipment has reached the end of its useful life, it must be taken to a recycling centre and processed separate from domestic waste. The cardboard box, the plastic contained in the packaging, and the parts that make up this router can be recycled in accordance with regionally established regulations.
-
Page 4: Table Of Contents
Table of Contents CHAPTER 1 SUMMARY ........................4 CHAPTER 2 CHANGE PASSWORD ....................5 2.1 P ............................. 5 ASSWORDS 2.2 D ......................... 5 EFAULT ETTINGS CHAPTER 3 ROUTER’S CONFIGURATION ................... 6 3.1 D ....................6 YNAMIC MULTI CONFIGURATION 3.1.1 Setup WAN port using manual setup ................. 6 3.1.2 Setup LAN port ......................... -
Page 5: Chapter 1 Summary
Wizard included in the kit for the Microsoft Windows SO. We recommended using the Telefonica’s Wizard. The CT-5365 contains state of the art security features, such as WPA data encryption, Firewall and VPN pass through. -
Page 6: Chapter 2 Change Password
Chapter 2 Change password This section describes how to access the device via the web user interface using an Internet browser such as Microsoft Internet Explorer (version 5.0 and later). 2.1 Passwords The Passwords option configures the user account access passwords for the device. Access to the device is limited to the following user accounts: 1234 is to be used for local unrestricted access control. -
Page 7: Chapter 3 Router's Configuration
Chapter 3 Router’s configuration After login, the Quick Setup screen will appear. It is the default screen when no connections exist. It allows for the configuration of DSL and IP settings. 3.1 Dynamic multi-configuration 3.1.1 Setup WAN port using manual setup Follow these steps to configure the WAN interfaces. - Page 8 STEP 3: Select PPP over Ethernet (PPPoE) and click Next. The following screen appears. Enter the Username and Password and select the connection options you wish. Review the descriptions below for more details. Click Next to continue. PPP Username / PPP Password The PPP Username and the PPP password requirement are dependent on the particular requirements of the service provider.
- Page 9 Dial on Demand The device can be configured to disconnect if there is no activity for a period of time by selecting this check box. When the checkbox is ticked, you must enter the inactivity timeout period. The timeout period ranges from 1 to 4320 minutes. PPP IP Extension The PPP IP Extension is a special feature deployed by some service providers.
-
Page 10: Setup Lan Port
Enable WAN Service checkbox: Tick this item to enable the ATM service. Untick it to stop the ATM service. Service Name: This is the WAN Service label. STEP 5: Click Next to display the WAN Setup - Summary screen that presents the entire configuration summary. - Page 11 NOTE: NAT is enabled above so UPnP is shown (see underlined notes below). Consult the field descriptions below for more details. IP Address: Enter the IP address for the LAN port. Subnet Mask: Enter the subnet mask for the LAN port. Enable UPnP: Tick the box to enable Universal Plug and Play.
-
Page 12: Setup Access Control
NOTE: The Save button saves new settings to allow continued configuration while the Save/Reboot button not only saves new settings but also reboots the device to apply the new configuration (i.e. all new settings). 3.1.3 Setup Access control The Access Control option under the Management menu bar configures access related parameters in three areas: Services, IP Addresses, and Passwords. -
Page 13: Static Multi-Configuration
Control Mode is enabled, only the IP addresses listed here can access the device. Before enabling Access Control Mode, add IP addresses with the Add button. On this screen, enter the IP address, subnet mask, and interface to which you wish to give management permissions. - Page 14 STEP 1: Tick the DSL Auto-connect checkbox on the Quick Setup screen. STEP 2: Click Next to start the setup process. Follow the on screen prompts. STEP 3: After setup is complete, the device will reboot with the following shown. NOTE: After the device reboots, the ¡Error! No se encuentra el origen de la referencia.
- Page 15 STEP 2: Adjust the VPI/VCI settings for the connection you wish to establish. Select Enable Quality Of Service if required. Click Next to continue. STEP 3: Select IP over ATM (IPoA) and click Next. The following screen appears. NOTE: Since DHCP is not supported over IPoA, users must manually enter the IP address or WAN interface for the default gateway and the DNS server addresses (primary and secondary), as provided by their ISP.
- Page 16 Enable NAT If the LAN is configured with a private IP address, the user should select this checkbox. The NAT submenu will display after the next reboot. The user can then configure NAT-related features. If a private IP address is not used on the LAN side, this checkbox should not be selected so as to free up system resources.
- Page 17 The Device Setup screen allows the user to configure the LAN interface IP address, subnet mask, and DHCP server. To enable DHCP, select Enable DHCP server and enter starting and ending IP addresses and the leased time. This setting configures the router to automatically assign IP, default gateway and DNS server addresses to every PC on your LAN.
-
Page 18: Setup Access Control
STEP 8: Click Save/Reboot to apply these settings. The configuration will be saved to flash memory and then the device will reboot. After the device reboots, the Web UI should refresh the browser window. If the browser does not refresh, restart the browser and login again. 3.2.2 Setup Access control The Access Control option under the Management menu bar configures access related parameters in three areas: Services, IP Addresses, and Passwords. - Page 19 NOTE: The WAN column is present if the WAN interface is active. Only the LAN side will be displayed if the WAN interface is down. IP Addresses The IP Addresses option limits local access by IP address. When the Access Control Mode is enabled, only the IP addresses listed here can access the device.
-
Page 20: Single Dynamic Configuration (Bridging)
3.3 Single dynamic configuration (bridging) 3.3.1 Setup WAN port Follow these steps to configure the WAN interfaces. STEP 1: To Add a new WAN connection, click the Add button. Heading Description VPI/VCI ATM VPI (0-255) / VCI (32-65535) Con. ID WAN connection ID number Category ATM service category... - Page 21 VlanId VLAN ID is used for VLAN Tagging (IEEE 802.1Q) State Shows the connection state of the WAN connection Remove To remove a connection select the radio button in this column and click the Remove button under the table. Edit Used to edit connections STEP 2: Adjust the VPI/VCI settings for the connection you wish to establish.
-
Page 22: Setup Lan Port
STEP 5: Click Save/Reboot to apply these settings. The configuration will be saved to flash memory and then the device will reboot. After the device reboots, the Web UI should refresh the browser window. If the browser does not refresh, restart the browser and login again. 3.3.2 Setup LAN port This screen allows the user to configure the LAN Interface on the device. -
Page 23: Setup Access Control
NOTE: NAT is enabled above so UPnP is shown (see underlined notes below). Consult the field descriptions below for more details. IP Address: Enter the IP address for the LAN port. Subnet Mask: Enter the subnet mask for the LAN port. Enable UPnP: Tick the box to enable Universal Plug and Play. - Page 24 Enable a service by ticking its checkbox. Click Save/Apply to activate. NOTE: The WAN column is present if the WAN interface is active. Only the LAN side will be displayed if the WAN interface is down. IP Addresses The IP Addresses option limits local access by IP address. When the Access Control Mode is enabled, only the IP addresses listed here can access the device.
-
Page 25: Single Static Configuration (Ipoa)
3.4 Single static configuration (IPoA) 3.4.1 Setup WAN port Follow these steps to configure the WAN interfaces. STEP 1: To Add a new WAN connection, click the Add button. Heading Description VPI/VCI ATM VPI (0-255) / VCI (32-65535) Con. ID WAN connection ID number Category ATM service category... - Page 26 Shows if IP QoS is enabled or disabled VlanId VLAN ID is used for VLAN Tagging (IEEE 802.1Q) State Shows the connection state of the WAN connection Remove To remove a connection select the radio button in this column and click the Remove button under the table.
- Page 27 NOTE: Since DHCP is not supported over IPoA, users must manually enter the IP address or WAN interface for the default gateway and the DNS server addresses (primary and secondary), as provided by their ISP. Step 4: Click Next. The following screen appears. Enable NAT If the LAN is configured with a private IP address, the user should select this checkbox.
-
Page 28: Setup Lan Port
STEP 6: Click Save/Reboot to apply these settings. The configuration will be saved to flash memory and then the device will reboot. After the device reboots, the Web UI should refresh the browser window. If the browser does not refresh, restart the browser and login again. 3.4.2 Setup LAN port This screen allows the user to configure the LAN Interface on the device. -
Page 29: Setup Access Control
NOTE: NAT is enabled above so UPnP is shown (see underlined notes below). Consult the field descriptions below for more details. IP Address: Enter the IP address for the LAN port. Subnet Mask: Enter the subnet mask for the LAN port. Enable UPnP: Tick the box to enable Universal Plug and Play. - Page 30 NOTE: The WAN column is present if the WAN interface is active. Only the LAN side will be displayed if the WAN interface is down. IP Addresses The IP Addresses option limits local access by IP address. When the Access Control Mode is enabled, only the IP addresses listed here can access the device.
-
Page 31: Nat
3.5 NAT To display this option, NAT must be enabled in at least one PVC shown on the ¡Error! No se encuentra el origen de la referencia. - ¡Error! No se encuentra el origen de la referencia. screen. (NAT is not an available option in Bridge mode) 3.5.1 Virtual Servers Virtual Servers allow you to direct incoming traffic from the WAN side (identified by Protocol and External port) to the Internal server with private IP addresses on the... - Page 32 Select a Service User should select the service from the list. Custom Server User can enter the name of their choice. Server IP Address Enter the IP address for the server. External Port Start Enter the starting external port number (when you select Custom Server).
-
Page 33: Wireless
3.6 Wireless The Wireless submenu provides access to WLAN configuration settings including wireless network name, channel restrictions (based on country), security, and quality of services features, access point or bridging behavior and station info. 3.6.1 Basic The Basic option allows you to configure basic features of the wireless LAN interface. You can enable or disable the wireless LAN interface, hide the network from active scans, set the wireless network name (also known as SSID) and restrict the channel set based on country requirements. -
Page 34: Security
Field Description Country A drop-down menu that permits worldwide and specific national settings. Each country listed below enforces specific regulations limiting channel range: US= worldwide Japan=1-14 Jordan= 10-13 Israel= 1-13 Wireless The Guest SSID (Virtual Access Point) can be enabled by Guest selecting the Enable Wireless Guest Network checkbox. - Page 35 Network Authentication This option specifies whether a network key is used for authentication to the wireless network. If network authentication is set to Open, then no authentication is provided. Despite this, the identity of the client is still verified. Each authentication type has its own settings. For example, selecting 802.1X authentication will reveal the RADIUS Server IP address, Port and Key fields.
- Page 36 WEP Encryption This option specifies whether data sent over the network is encrypted. The same network key is used for data encryption and network authentication. Four network keys can be defined although only one can be used at any one time. Use the Current Network Key list box to select the appropriate network key.
- Page 37 Step 1: Select WPA-PSK, WPA2-PSK or Mixed WPA2/WPA-PSK network authentication mode from the Manual Setup AP section of the Wireless Security screen. The example below shows WPA2-PSK mode. Steps 1 & 2 Step 2: Enter a WPA Pre-Shared Key and click the Save/Apply button. You will see the following dialog box if the Key is too short or too long.
- Page 38 The WPS push-button configuration provides a semi-automated configuration method. The WPS button on the front panel of the router can be used for this purpose or the Web User Interface (WUI) can be used exclusively. The WPS push-button configuration is described in the procedure below. It is assumed that the Wireless function is Enabled and that the router is configured as the Wireless Access Point (AP) of your wireless LAN.
- Page 39 Step 5: Go to your WPS wireless client and activate the push-button function. A screenshot of typical WPS client software is given below as an example. You can now proceed to Step 6 to check your connection. III. CHECK CONNECTION Step 6: If the WPS setup method was successful, you will be able access the wireless AP from the client.
-
Page 40: Mac Filter
Double-click the Wireless Network Connection icon from the Network Connections window (or the system tray) to confirm the new connection. It should appear as shown in the dialog-box below. 3.6.3 MAC Filter This option allows access to the router to be restricted based upon MAC addresses. Every network device has a unique 48-bit MAC address. -
Page 41: Advanced
To delete a filter, select it from the table below and click the Remove button. Option Description Off – Disables MAC filtering Restrict Allow – Permits access for the specified MAC addresses Mode Deny – Rejects access for the specified MAC addresses Lists the MAC addresses subject to the MAC Restrict Mode. - Page 42 interface. Among other things, you can select a particular channel on which to operate, force the transmission rate to a particular speed, set the fragmentation threshold, set the RTS threshold, set the wakeup interval for clients in power-save mode, set the beacon interval for the access point, set XPress mode and set whether short or long preambles are used.
- Page 43 Field Description split into smaller units suitable for the circuit size. Packets smaller than the specified fragmentation threshold value are not fragmented. Values between 256 and 2346 can be entered. The value should remain at its default setting of 2346, if possible, since setting the Fragmentation Threshold too low may result in poor performance.
-
Page 44: Station Info
3.6.5 Station Info This page shows authenticated wireless stations and their status. Click the Refresh button to update the list of stations in the WLAN. Field Description BSSID The BSSID is a 48-bit identity used to identify a particular BSS (Basic Service Set) within an area. In Infrastructure BSS networks, the BSSID is the MAC (Media Access Control) address of the AP (Access Point);... -
Page 45: Save And Reboot
Step 1: Obtain an updated software image file from your ISP. Step 2: Enter the path and filename of the firmware image file in the Software File Name field or click the Browse button to locate the image file. Step 3: Click the Update Software button once to upload and install the file. NOTE: The update process will take about 2 minutes to complete.