Table of Contents
Advertisement
Quick Links
3.5 GALLON PARTS WASHER
Assembly and Operating Instructions
®
3491 Mission Oaks Blvd., Camarillo, CA 93011
Visit our Web site at http://www.harborfreight.com
®
®
Copyright
1997 by Harbor Freight Tools
. All rights reserved. No portion of this manual
or any artwork contained herein may be reproduced in any shape or form without the
express written consent of Harbor Freight Tools.
For technical questions and replacement parts, please call 1-800-444-3353.
Advertisement
Table of Contents
Related Manuals for Chicago Electric 35740
Summary of Contents for Chicago Electric 35740
- Page 1 . All rights reserved. No portion of this manual or any artwork contained herein may be reproduced in any shape or form without the express written consent of Harbor Freight Tools. For technical questions and replacement parts, please call 1-800-444-3353.
-
Page 2: Specifications
Extinguish all cigarettes when cleaning. Industrial applications must follow OSHA requirements. DO NOT OVERFILL THE PARTS WASHER. Do not fill above the level of the parts tray or serious injury may occur. MATERIALS USED WHEN CLEANING MAY BE HARMFUL OR FATAL IF INHALED AND/OR SWALLOWED. -
Page 3: Grounding Instructions
USE EYE PROTECTION. Solvents can cause serious eye damage . Wear ANSI approved chemical splash safety goggles. Goggles are available from Harbor Freight Tools. When cleaning, be especially careful as solvents can be forcibly ejected from fluid and air passages. -
Page 4: Voltage Warning
Always inspect extension cords for any damage. If there are any loose, frayed, or exposed wires; damaged insulation; or defective connections, the cord must not be used. Harbor Freight Tools can supply UL listed and outdoor rated cords in multiple AWG rating if needed. - Page 5 When unpacking, check to make sure the following parts are included. All sizes listed below are approximate. If any parts are missing or broken, please call Harbor Freight Tools at the number on the cover of this manual. QTY. SKU 35740 For technical questions, please call 1-800-444-3353.
- Page 6 Step 1: Get out the LID HANDLE (#10); and two each of the SCREWS (#12), Lock Washers (#13), and NUTS (#14). Step 2: Attach HANDLE to LID (#2) as shown in Figure 1. (#2) Figure 1 — Attaching Handle to Lid SKU 35740 For technical questions, please call 1-800-444-3353. ASSEMBLY Screw Handle...
- Page 7 PUMP (#6). Step 2: On the outside of the TANK, put both ground wires (green with ring-ears) on the SCREW. Secure using (in the following order) a LOCK WASHER (#22), WASHER (#21), & NUT (#23).
- Page 8 Step 4: When attaching the right side of the SWITCH BOX, make sure the SCREW also secures the side of the CORD CLAMP that was left unattached in Step 3, above. SKU 35740 For technical questions, please call 1-800-444-3353. (#23)
- Page 9 Step 4: Do not run the PUMP without the FILTER (#7) attached. Step 5: Never leave PUMP running unattended. Step 6: Do not wash plastic parts when using petroleum based solvents. SKU 35740 For technical questions, please call 1-800-444-3353. Page 9...
-
Page 10: Parts List
AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACE- MENT PARTS THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO. SKU 35740 For technical questions, please call 1-800-444-3353. PARTS LIST QTY. -
Page 11: Parts Diagram
PARTS DIAGRAM NOTE: Some parts are listed and shown for illustration purposes only and are not available individually as replacement parts. REV 06/05 SKU 35740 For technical questions, please call 1-800-444-3353. Page 11...