Keep bystanders, children, and visitors away while operating a power tool. Distractions can cause you to lose control. Provide barriers or shields as needed. For technical questions, please call 1-800-444-3353. SKU 94280 Single Speed / 0.3 HP / 150 RPM 3-Prong with Ground 18 AWG x 3 C SJTX x 19 Ft.
Do not overreach. Keep proper footing and balance at all times. Proper footing and balance enables better control of this product in unexpected situations. For technical questions, please call 1-800-444-3353. SKU 94280 ELECTRICAL SAFETY eliminates the need for the three wire grounded...
Maintain labels and nameplates on the Floor Machine. These carry important information. If unreadable or missing, contact Harbor Freight Tools for a replace- ment. Wear ANSI-approved safety impact eye goggles and non-slip foot- wear when using the Floor Machine.
Page 5
It must be understood by the operator that common sense and caution are factors which cannot be built into this product, but must be supplied by the operator. SAVE THESE INSTRUCTIONS For technical questions, please call 1-800-444-3353. SKU 94280 Page 5...
OSHA requirements and complies with the applicable standards of Underwriters Laboratories, Inc., the Canadian Standard Association, and the National Electrical Code. (See Outlets for 2-Prong Plug.) For technical questions, please call 1-800-444-3353. SKU 94280 GROUNDING WARNING! Outlets for 2-Prong Plug...
Always replace a damaged extension cord or have it repaired by a qualified electri- cian before using it. Protect your extension cords from sharp objects, excessive heat, and damp or wet areas. For technical questions, please call 1-800-444-3353. SKU 94280 ExTENSION CORDS Page ...
Page 8
If any parts are missing or broken, please call Harbor Freight Tools at the number shown on the cover of this manual as soon as possible. For technical questions, please call 1-800-444-3353. SKU 94280 (120 OR 240 VOLT) ExTENSION CORD LENGTH...
Page 9
Pin (16) through the storage hole shown above. For transport, raise the Handle Tube (21) to its highest point. Then, insert the Lock- ing Pin (16) through the transport hole shown above. For technical questions, please call 1-800-444-3353. SKU 94280 ASSEMBLY storage transport...
Page 10
Then push down firmly on the Chassis to secure the Brush or Pad in place. NOTE: The Brushes and Foam Pad fit snugly onto the Brush Holder Pad, and may require additional effort to install. (See Figure E, next page.) For technical questions, please call 1-800-444-3353. SKU 94280 Page 10...
Lay the Floor Machine on its back with its Front Handle (26) lying on the floor sur- face. With both hands, pull out and remove the Carpet Brush (51), Floor Brush (52), or Foam Pad (54). For technical questions, please call 1-800-444-3353. SKU 94280 OPERATION POWER SWITCH (29) POWER SWITCH (29)
Irregular noises when Handle Screw (11) is loose. running. Pad Screws (25) are loose. For technical questions, please call 1-800-444-3353. SKU 94280 TROUBLESHOOTING Possible Cause Possible Solution Make sure the power plug is plugged into a working, 115 volt, grounded, electrical outlet.
Front Handle Screw (ST3.5 x 16) Note: Some parts are listed and shown for illustration purposes only, and are not available individually as replacement parts. For technical questions, please call 1-800-444-3353. SKU 94280 PARTS LIST Q’ty Part Description Cord Clamp...
LIMITED 90 DAY WARRANTY Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards, and warrants to the original purchaser that this product is free from defects in materials and workmanship for the period of 90 days from the date of purchase.