Comtrend Corporation CT-536+ User Manual
  1. Manuals
  2. Brands
  3. Comtrend Corporation Manuals
  4. Wireless Router
  5. CT-536+
  6. User manual
Comtrend Corporation CT-536+ User Manual

Comtrend Corporation CT-536+ User Manual

4-port wireless adsl2+ router
Hide thumbs
Table of Contents

Advertisement

Quick Links

CT-536+
4-Port Wireless
ADSL2+ Router
User's Manual
Version A1.7, October 27, 2006
261056-024

Advertisement

Table of Contents
loading

Related Manuals for Comtrend Corporation CT-536+

Summary of Contents for Comtrend Corporation CT-536+

  • Page 1 CT-536+ 4-Port Wireless ADSL2+ Router User’s Manual Version A1.7, October 27, 2006 261056-024...
  • Page 2 Copyright Copyright© 2006 Comtrend Corporation. All rights reserved. The information and messages contained herein are proprietary to Comtrend Corporation. No part of this document may be translated, transcribed, reproduced, in any form, or by any means without prior written permission by Comtrend Corporation.

  • Page 3: Table Of Contents

    Table of Contents CHAPTER 1 INTRODUCTION ......................5 ..........................5 EATURES ..........................6 PPLICATION LED I ....................7 RONT ANEL NDICATORS CHAPTER 2 INSTALLATION ......................8 ......................8 ARDWARE NSTALLATION USB D ....................9 NSTALLING THE RIVER CHAPTER 3 LOGIN VIA THE WEB BROWSER ..............14 IP A ..........................14 DDRESS .........................15...
  • Page 4 6.3.1 Virtual Servers ........................50 6.3.2 Port Triggering .......................52 6.3.3 DMZ Host ........................53 6.3.4 ALG ..........................54 ..........................55 ECURITY 6.4.1 IP Filtering ........................55 6.4.2 Parental Control ......................58 ......................59 UALITY OF ERVICE ..........................62 OUTING 6.6.1 Default Gateway ......................62 6.6.2 Static Route........................63 6.6.3 RIP..........................64 DNS ............................65 6.7.1 DNS Server ........................65...
  • Page 5 ........................98 PDATE SOFTWARE ........................99 AVE AND EBOOT APPENDIX A: FIREWALL ......................100 APPENDIX B: PIN ASSIGNMENTS....................106 APPENDIX C: SPECIFICATIONS....................107 APPENDIX D: SSH CLIENT ......................109...

  • Page 6: Chapter 1 Introduction

    Chapter 1 Introduction The CT-536+ is an 802.11g (54Mbps) wireless and wired Local Area Network (WLAN) ADSL router. Four 10/100 Base-T Ethernet ports provide wired LAN connectivity with an integrated 802.11g WiFi WLAN Access Point (AP) for wireless connectivity. The CT-536+ ADSL router provides state of the art security features such as WPA data encryption Firewall, VPN pass through.

  • Page 7: Application

    Application The following diagram depicts the application of the CT-536+ on a wireless network.

  • Page 8: Front Panel Led Indicators

    Front Panel LED Indicators The front panel LEDs are shown in the picture below, followed by an explanation in the table below. Color Mode Function POWER Green The router is powered up. The router is powered down. Green An Ethernet Link is established. 1x~4x An Ethernet Link is not established.

  • Page 9: Chapter 2 Installation

    Chapter 2 Installation Hardware Installation In the rear panel, there is a reset button. To load the factory default settings, hold the reset button down for at least 5 seconds. Reset button Follow the instructions below to complete the hardware connections. Connection to LINE port If you wish to connect both the router and a telephone, connect the LINE port to a POTS splitter with a RJ11 connection cable.

  • Page 10: Installing The Usb Driver

    Connection to Power Connect the Power jack to the shipped power cord. Attach the power adapter to the wall outlet or other AC source. After all connections have been made, turn the power-switch to the on position. After power on, the router performs a self-test. Wait for a few seconds until the test is finished, then the router will be ready to operate.
  • Page 11 STEP 2: When the screen displays as below, click the Next button. Note: This screen won’t be displayed if the USB Driver has been previously un/installed. STEP 3: When the screen displays as below, select Search for a suitable driver and click the Next button.
  • Page 12 STEP 4: Select Specify a location and click the Next button. If you are installing the software from a disk, insert the disk. STEP 5: Select the location of the file using the Browse button. Normally, the file is on the CD-ROM shipped with the device.
  • Page 13 STEP 6: Locate the file, and click the Open button. STEP 7: When the screen displays as below, click the OK button.
  • Page 14 STEP 8: When the screen below displays, click the NEXT button. STEP 9: Click the Finish button, when the screen displays as below. STEP 10: Installation is complete.

  • Page 15: Chapter 3 Login Via The Web Browser

    Chapter 3 Login via the Web Browser This section describes how to manage the router via a Web browser via the remote end. You can use a web browser such as Microsoft Internet Explorer, or Netscape Navigator. (The Web page is best viewed with Microsoft Internet Explorer 5.0 and later): A unique default user account is assigned with user name root and password 12345.

  • Page 16: Login Procedure

    Login Procedure Perform the following steps to bring up the Web user interface and configure the CT-536+. To log on to the system from the Web browser, follow the steps below: STEP 1: Start your Internet browser. Type the IP address for the router in the Web address field.

  • Page 17: Default Settings

    Default Settings During power on initialization, the CT-536+ initializes all configuration attributes to default values. It will then read the configuration profile from the Permanent Storage section on the flash memory. The default attributes are overridden when identical attributes with different values are configured. The configuration profile in Permanent Storage can be created via the Web user interface, the console, or telnet user interface, or other management protocols.

  • Page 18: Chapter 4 Quick Setup

    Chapter 4 Quick Setup After login, the Quick Setup screen appears as shown. Note: The selections available on the left side of menu are based upon the configured connection. If you configure a PVC and Click Save/Reboot, the Device Info screen will be displayed.

  • Page 19: Wan

    Click Device Info on the menu bar to display the WAN option. Then, click WAN on the Device Info menu bar to display the configured PVC(s) and the status. VPI/VCI Shows the values of the ATM VPI/VCI Con. ID Shows the connection ID Category Shows the ATM service classes Service...

  • Page 20: Statistics

    Statistics Selection of the Statistics screen provides statistics for the Network Interface of LAN, WAN, ATM and ADSL. All statistics screens are updated every 15 seconds.

  • Page 21: Lan Statistics

    4.2.1 LAN Statistics The Network Statistics screen shows interface statistics for ATM AAL5 interface, Ethernet and USB interfaces. (The Network Statistics screen shows interface statistics for LAN of Ethernet and USB interfaces. This provides byte transfer, packet transfer, Error and Drop statistics for the LAN interface.)

  • Page 22: Wan Statistics

    4.2.2 WAN Statistics Service Shows the service type VPI/VCI Shows the values of the ATM VPI/VCI Protocol Shows the connection type, such as PPPoE, PPPoA, etc. Interface Shows connection interfaces Received/Transmitted - Bytes Rx/TX (receive/transmit) packet in Bytes - Pkts Rx/TX (receive/transmit) packets - Errs Rx/TX (receive/transmit) the packets which are...

  • Page 23: Atm Statistics

    4.2.3 ATM statistics The following figure shows the ATM statistics screen. ATM Interface Statistics Field Description In Octets Number of received octets over the interface Out Octets Number of transmitted octets over the interface In Errors Number of cells dropped due to uncorrectable HEC errors In Unknown Number of received cells discarded during cell header validation, including cells with unrecognized VPI/VCI values, and cells with...
  • Page 24 ATM AAL5 Layer Statistics over ADSL interface Field Description In Octets Number of received AAL5/AAL0 CPCS PDU octets Out Octets Number of received AAL5/AAL0 CPCS PDUs octets transmitted In Ucast Pkts Number of received AAL5/AAL0 CPCS PDUs passed to a higher-layer for transmission Out Ucast Pkts Number of received AAL5/AAL0 CPCS PDUs received from a...

  • Page 25: Adsl Statistics

    4.2.4 ADSL Statistics The following figure shows the ADSL Network Statistics screen. Within the ADSL Statistics window, a bit Error Rate Test can be started using the ADSL BER Test button. The Reset button resets the statistics.
  • Page 26 Field Description Mode Line Coding format, that can be selected G.dmt, G.lite, T1.413, ADSL2 Type Channel type Interleave or Fast Line Coding Trellis On/Off Status Lists the status of the DSL link Link Power State Link output power state. SNR Margin (dB) Signal to Noise Ratio (SNR) margin Attenuation (dB) Estimate of average loop attenuation in the downstream...

  • Page 27: Route

    4.2.5 Route Choose Route to display the routes that the route information has learned. 4.2.6 Click ARP to display the ARP information.

  • Page 28: Dhcp

    4.2.7 DHCP Click DHCP to display the DHCP information.

  • Page 29: Chapter 5 Quick Setup

    Chapter 5 Quick Setup The Quick Setup allows the user to configure the ADSL router for DSL connectivity and Internet access. It also guides the user though the WAN network setup first and then the LAN interface setup. You can either manually customize the router or follow the online instruction to set up the router.

  • Page 30: Auto Quick Setup

    Note: Up to eight PVC profiles can be configured and saved on the flash memory. To activate a particular PVC profile, you need to navigate all the Quick Setup pages until the last summary page, then click on the Finish button and reboot the system. Auto Quick Setup The auto quick setup requires the ADSL link to be up.

  • Page 31: Manual Quick Setup

    Manual Quick Setup STEP 1: Click Quick Setup and un-tick the DSL Auto-connect checkbox to enable manual configuration of the connection type. Un-tick this checkbox to enable manual setup and display the following screen. STEP 2: Enter the Virtual Path Identifier (VPI) and Virtual Channel Identifier (VCI). Select Enable Quality Of Service if required.
  • Page 32 STEP 3: STEP 3: Then, choose the Encapsulation mode. Select Enable 802.1q (by ticking the box) if required, and input a number for the VLAN ID. Click Next. STEP 4: Click Next to display the following screen. Choosing different connection types pops up different settings requests.

  • Page 33: Ppp Over Atm (Pppoa) And Ppp Over Ethernet (Pppoe)

    5.2.1 PPP over ATM (PPPoA) and PPP over Ethernet (PPPoE) 1. Select the PPP over ATM (PPPoA) or PPP over Ethernet (PPPoE) radio button and click Next. The following screen appears: PPP USERNAME/PPP PASSWORD The PPP Username and the PPP password requirement are dependent on the particular requirements of the ISP or the ADSL service provider.
  • Page 34 PPP IP Extension The PPP IP Extension is a special feature deployed by some service providers. Unless your service provider specially requires this setup, do not select it. The PPP IP Extension supports the following conditions: Allows only one PC on the LAN The public IP address assigned by the remote side using the PPP/IPCP protocol is actually not used on the WAN PPP interface.
  • Page 35 Use Static IP Address Unless your service provider specially requires this setup, do not select it. If selected, enter your static IP address. This option allows us to change the MTU size for WAN interface, PPPoE and PPPoA. The default value is 1492 for PPPoE and 1500 for PPPoA. 3.
  • Page 36 4. The following screen will be displayed. To enable the wireless function, select the box (by clicking on it) and input the SSID. Then, click Next. 5. Click Next to display the WAN Setup-Summary screen that presents the entire configuration summary. Click Save/Reboot if the settings are correct. Click Back if you wish to modify the settings.
  • Page 37 6. After clicking Save/Reboot, the router will save the configuration to the flash memory, and reboot. The Web UI will not respond until the system is brought up again. After the system is up, the Web UI will refresh to the Device Info page automatically.

  • Page 38: Mac Encapsulation Routing (Mer)

    5.2.2 MAC Encapsulation Routing (MER) To configure MER, do the following. 1. Select Quick Setup and click Next. 2. Enter the PVC Index provided by the ISP and click Next. 3. Select the MAC Encapsulation Routing (MER) radio button, and click Next. The following screen appears.
  • Page 39 4. Click Next to display the following screen. Enable NAT checkbox: If the LAN is configured with a private IP address, the user should select this checkbox. The NAT submenu on the left side main panel will be displayed after reboot. The user can then configure NAT-related features after the system comes up.
  • Page 40 5. Upon completion, click Next. The following screen appears. The Device Setup page allows the user to configure the LAN interface IP address and DHCP server. If the user would like this ADSL router to assign dynamic IP addresses, DNS server and default gateway to other LAN devices, select the radio box Enable DHCP server on the LAN to enter the starting IP address and end IP address and DHCP lease time.
  • Page 41 6. After entering your settings, select Next to display the following screen. The WAN Setup-Summary screen presents the entire configuration summary. Click Save/Reboot if the settings are correct. Click Back if you wish to modify the settings. 7. The following screen will be displayed. To enable the wireless function, select the box (by clicking on it) and input the SSID.

  • Page 42: 5.2.3 Ip Over Atm

    5.2.3 IP Over ATM To configure IP Over ATM, 1. Select Quick Setup and click Next. 2. Enter the PVC Index and click Next. 3. Type the VPI and VCI values provided by the ISP and click Next. 4. Select the IP over ATM (IPoA) radio button and click Next. The following screen appears.
  • Page 43 Enable NAT checkbox If the LAN is configured with a private IP address, the user should select this checkbox. The NAT submenu on the left side main panel will be displayed after reboot. The user can then configure NAT-related features after the system comes up.
  • Page 44 The user must configure the IP Address and the Subnet Mask. To use the DHCP service on the LAN, select the Enable DHCP server checkbox, and enter the Start IP addresses, the End IP address and DHCP lease time. This configures the router to automatically assign IP addresses, default gateway address and DNS server addresses to each of your PCs.
  • Page 45 8. The following screen will be displayed. To enable the wireless function, select the box (by clicking on it) and input the SSID. Then, click Next. The following screen will be displayed. 9. After clicking Save/Reboot, the router will save the configuration to the flash memory, and reboot.

  • Page 46: 5.2.4 Bridging

    5.2.4 Bridging Select the bridging mode. To configure Bridging, do the following. 1. Select Quick Setup and click Next. 2. Enter the PVC Index and click Next. 3. Type in the VPI and VCI values provided by the ISP and click Next. 4.
  • Page 47 6. The following screen will be displayed. To enable the wireless function, select the box (by clicking on it) and input the SSID. Then, click Next. The following screen will be displayed. The WAN Setup-Summary screen presents the entire configuration summary. Click Save/Reboot if the settings are correct.

  • Page 48: Chapter 6 Advanced Setup

    Chapter 6 Advanced Setup This chapter explains: WAN, LAN, Routing, DSL and Port Mapping…... VPI/VCI ATM VPI (0-255) / VCI (32-65535) Con. ID ID for WAN connection Category ATM service category, e.g. UBR, CBR… Service Name of the WAN connection Interface Name of the interface for WAN Protocol...

  • Page 49: Wan

    For further information on WAN please reference section: 4.1, Page 18.

  • Page 50: Lan

    Configure the DSL Router IP Address and Subnet Mask for LAN interface. Save button only saves the LAN configuration data. Save/Reboot button saves the LAN configuration data and reboots the router to make the new configuration effective. IP Address: Enter the IP address for the LAN port. Subnet Mask: Enter the subnet mask for the LAN port.

  • Page 51: Nat

    To display the NAT function, you need to enable the NAT feature in the WAN Setup. 6.3.1 Virtual Servers Virtual Server allows you to direct incoming traffic from WAN side (identified by Protocol and External port) to the Internal server with private IP address on the LAN side.
  • Page 52 Select a Service User should select the service from the list. Custom Server User can enter the name of their choice. Server IP Address Enter the IP address for the server. External Port Start Enter the starting external port number (when you select Custom Server).

  • Page 53: Port Triggering

    6.3.2 Port Triggering Some applications require that specific ports in the Router's firewall be opened for access by the remote parties. Port Trigger dynamically opens up the 'Open Ports' in the firewall when an application on the LAN initiates a TCP/UDP connection to a remote party using the 'Triggering Ports'.

  • Page 54: Dmz Host

    Select an Application User should select the application from the list. Or Custom Application Or User can enter the name of their choice. Trigger Port Start Enter the starting trigger port number (when you select custom application). When an application is selected the port ranges are automatically configured.

  • Page 55: Alg

    6.3.4 SIP ALG is Application layer gateway. If the user has an IP phone(SIP) or VoIP gateway(SIP) behind the ADSL router, the SIP ALG can help VoIP packet passthrough the router (NAT enabled). Note: SIP (Session Initiation Protocol, RFC3261) is the protocol of choice for most VoIP (Voice over IP) phones to initiate communication.

  • Page 56: Security

    Security To display the Security function, you need to enable the firewall feature in the WAN Setup. 6.4.1 IP Filtering IP filtering allows you to create a filter rule to identify outgoing/incoming IP traffic by specifying a new filter name and at least one condition below. All of the specified conditions in this filter rule must be satisfied for the rule to take effect.
  • Page 57 Filter Name Type a name for the filter rule. Protocol User can select from: TCP, TCP/UDP, UDP or ICMP. Source IP address Enter source IP address. Source Subnet Mask Enter source subnet mask. Source Port (port or port:port) Enter source port number. Destination IP address Enter destination IP address.
  • Page 58 Incoming Note: The default setting for Incoming is Accepted. To add a filtering rule, simply click the Add button. The following screen will be displayed. To configure the parameters, please reference Outgoing table above.

  • Page 59: Parental Control

    6.4.2 Parental Control Parental control: allows parents, schools, and libraries to set access times for Internet use. To add a parental control, simply click the Add button. The following screen will be displayed. Username: Name of the Filter. MAC: Set the MAC address to access the Internet. Mon, Tue, Wed, Thu, Fri, Sat, Sun: Set which days that will have block restrictions to Internet access.

  • Page 60: Quality Of Service

    Quality of Service To display the QoS function, you need to enable the QoS feature in the WAN Setup. Choose Add to configure network traffic classes. The following screen will be displayed:...
  • Page 61 The screen creates a traffic class rule to classify the upstream traffic, assign queuing priority and optionally overwrite the IP header TOS byte. A rule consists of a class name and at least one condition below. All of the specified conditions in this classification rule must be satisfied for the rule to take effect.
  • Page 62 SET-1 Physical LAN Port User can select from: ENET, ENET(1-4), USB or Wireless. Protocol User can select from: TCP, TCP/UDP, UDP or ICMP. Source IP Address Enter the source IP address. Source Subnet Mask Enter the subnet mask for the source IP address. Source Port (port or Enter source port number.

  • Page 63: Routing

    Routing The Routing dialog box allows you to configure Default gateway, Static Route and RIP. 6.6.1 Default Gateway If ‘Enable Automatic Assigned Default Gateway’ checkbox is selected, this router will accept the first received default gateway assignment from one of the PPPoA, PPPoE or MER/DHCP enabled PVC(s).

  • Page 64: Static Route

    6.6.2 Static Route Choose Static Route to display the Static Route screen. The Static Route screen lists the configured static routes, and allows configuring static routes. Choose Add or Remove to configure the static routes. To add static route, click the Add button to display the following screen. Enter the destination network address, subnet mask, gateway AND/OR available WAN interface then click Save/Apply to add the entry to the routing table.

  • Page 65: 6.6.3 Rip

    6.6.3 RIP To activate RIP for the device, select the 'Enabled' radio button for Global RIP Mode. To configure an individual interface, select the desired RIP version and operation, followed by placing a check in the 'Enabled' checkbox for the interface. Click the 'Save/Apply' button to save the configuration, and to start or stop RIP based on the Global RIP mode selected.

  • Page 66: Dns

    6.7.1 DNS Server If 'Enable Automatic Assigned DNS' checkbox is selected, this router will accept the first received DNS assignment from one of the PPPoA, PPPoE or MER/DHCP enabled PVC(s) during the connection establishment. If the checkbox is not selected, enter the primary and optional secondary DNS server IP addresses.

  • Page 67: Dynamic Dns

    6.7.2 Dynamic DNS The Dynamic DNS service allows you to alias a dynamic IP address to a static hostname in any of the many domains, allowing your DSL router to be more easily accessed from various locations on the Internet. To add a dynamic DNS service, simply click the Add button.
  • Page 68 D-DNS provider Select a dynamic DNS provider from the list Hostname Enter the name for the dynamic DNS server. Interface Select the interface from the list Username Enter the username for the dynamic DNS server. Password Enter the password for the dynamic DNS server.

  • Page 69: Dsl

    To access the DSL settings, First click On Advanced Setup and then click on DSL. The DSL Settings dialog box allows you to select an appropriate modulation mode. Option Description G.dmt Enabled Sets G.Dmt if you want the system to use G.Dmt mode. G.Lite Enabled Sets G.Lite if you want the system to use G.Lite mode.

  • Page 70: Port Mapping

    Port Mapping Port Mapping supports multiple ports to PVC and bridging groups. Each group will perform as an independent network. To support this feature, you must create mapping groups with appropriate LAN and WAN interfaces using the Add button. The Remove button will remove the grouping and add the ungrouped interfaces to the Default group.
  • Page 71 To create a group from the list, first enter the group name and then select from the available interfaces on the list.

  • Page 72: Chapter 7 Wireless

    Chapter 7 Wireless The Wireless dialog box allows you to enable the wireless capability, hide the access point, set the wireless network name and restrict the channel set. Wireless Basic Screen The Basic option allows you to configure basic features of the wireless LAN interface. You can enable or disable the wireless LAN interface, hide the network from active scans, set the wireless network name (also known as SSID) and restrict the channel set based on country requirements.
  • Page 73 Option Description Enable Wireless A checkbox that enables or disables the wireless LAN interface. When selected, the Web UI displays Hide Access point, SSID, and County settings. The default is Enable Wireless. Hide Access Point Select Hide Access Point to protect ADSL router access point from detection by wireless active scans.

  • Page 74: Security

    7.1.1 Security Security options include authentication and encryption services based on the wired equivalent privacy (WEP) algorithm. WEP is a set of security services used to protect 802.11 networks from unauthorized access, such as eavesdropping; in this case, the capture of wireless network traffic. When data encryption is enabled, secret shared encryption keys are generated and used by the source station and the destination station to alter frame bits, thus avoiding disclosure to eavesdroppers.
  • Page 75 Option Description Network It specifies the network authentication. When this checkbox is Authentication selected, it specifies that a network key be used for authentication to the wireless network. If the Network Authentication (Shared mode) checkbox is not shared (that is, if open system authentication is used), no authentication is provided.
  • Page 76 Choosing WPA-PSK, you must enter WPA Pre-Shared Key and Group Rekey Interval. It specifies that a network key is used to encrypt the data is sent over Encryption the network. When this checkbox is selected, it enables data encryption and prompts the Encryption Strength drop-down menu. Data Encryption (WEP Enabled) and Network Authentication use the same key.

  • Page 77: Mac Filter

    7.1.2 MAC Filter This MAC Filter page allows access to be restricted/allowed based on a MAC address. All NICs have a unique 48-bit MAC address burned into the ROM chip on the card. When MAC address filtering is enabled, you are restricting the NICs that are allowed to connect to your access point.
  • Page 78 Option Description MAC Restrict Mode Radio buttons that allow settings of; Off: MAC filtering function is disabled. Allow: Permits PCs with listed MAC addresses to connect to the access point. Deny: Prevents PCs with listed MAC from connecting to the access point.

  • Page 79: Wireless Bridge

    7.1.3 Wireless Bridge This page allows you to configure wireless bridge features of the wireless LAN interface. You can select Wireless Bridge (also known as Wireless Distribution System) to disable access point functionality. Selecting Access Point enables access point functionality. Wireless bridge functionality will still be available and wireless stations will be able to associate to the AP.

  • Page 80: Advanced

    7.1.4 Advanced The Advanced page allows you to configure advanced features of the wireless LAN interface. You can select a particular channel on which to operate, force the transmission rate to a particular speed, set the fragmentation threshold, set the RTS threshold, set the wakeup interval for clients in power-save mode, set the beacon interval for the access point, set XPress mode and set whether short or long preambles are used.
  • Page 81 Channel Drop-down menu that allows selection of specific channel. Rate Drop-down menu that specifies the following fixed rates: Auto: Default. Uses the 11 Mbps data rate when possible but drops to lower rates when necessary. 1 Mbps, 2Mbps, 5.5Mbps, or 11Mbps fixed rates. The appropriate setting is dependent on signal strength.
  • Page 82 Beacon Interval The amount of time between beacon transmissions. Each beacon transmission identifies the presence of an access point. By default, radio NICs passively scan all RF channels and listen for beacons coming from access points to find a suitable access point. Before a station enters power save mode, the station needs the beacon interval to know when to wake up to receive the beacon (and learn whether there are buffered frames at the access point).

  • Page 83: Station Info

    7.1.5 Station Info This page shows authenticated wireless stations and their status. BSSID The BSSID is a 48bit identity used to identify a particular BSS (Basic Service Set) within an area. In Infrastructure BSS networks, the BSSID is the MAC (Medium Access Control) address of the AP (Access Point) and in Independent BSS or ad hoc networks, the BSSID is generated randomly.

  • Page 84: Chapter 8 Diagnostics

    Chapter 8 Diagnostics The Diagnostics menu provides feedback on the connection status of the CT-536+ and the ADSL link. The individual tests are listed below. If a test displays a fail status, click Rerun Diagnostic Tests at the bottom of this page to make sure the fail status is consistent.
  • Page 85 Down: Indicates that the DSL Router does not detect the wireless network. ADSL Pass: Indicates that the DSL modem has detected a DSL Synchronization signal from the telephone company. A solid WAN LED on the router also indicates the detection of a DSL signal from the telephone company.

  • Page 86: Chapter 9 Management

    Chapter 9 Management The Management section of the CT-536+ supports the following maintenance functions and processes: Settings System log SNMP Agent Internet Time Access Control Update software Save/Reboot Settings The Settings option allows you to back up your settings to a file, retrieve the setting file, and restore the settings.

  • Page 87: Configuration Backup

    9.1.1 Configuration Backup The Backup option under Management>Settings save your router configurations to a file on your PC. Click BACKUP Settings in the main window. You will be prompted to define the location of the backup file to save. After choosing the file location, click Backup Settings.

  • Page 88: Tools - Update Settings

    9.1.2 Tools – Update Settings The Update option under Management>Settings update your router settings using your saved files.

  • Page 89: Restore Default

    9.1.3 Restore Default Clicking the Restore Default Configuration option in the Restore Settings screen can restore the original factory installed settings. NOTE: This entry has the same effect as the hardware reset-to-default button. The CT-536+ board hardware and the boot loader support the reset to default button.
  • Page 90 Default settings The CT-536+ default settings are LAN port IP= 192.168.1.1, subnet mask = 255.255.255.0 Local user name: root Password: 12345 Remote user name: root Remote user password: 12345 After the Restore Default Configuration button is selected, the following screen appears.

  • Page 91: System Log

    System Log The System Log option under Management>Settings allows you to view the system events log, or to configure the System Log options. The default setting of system log is disabled. Follow the steps below to enable and view the system log. 1.
  • Page 92 Option Description Indicates whether the system is currently recording events. The user can enable or disable event logging. By default, it is disabled. To enable it, tick Enable and then Apply button. Log level Allows you to configure the event level and filter out unwanted events below this level.

  • Page 93: Snmp Agent

    3. Click View System Log. The results are displayed as follows. SNMP Agent Simple Network Management Protocol (SNMP) allows a management application to retrieve statistics and status from the SNMP agent in this device. The System Log option under Management>Settings allows you to view the system events log, or to configure the System Log options.

  • Page 94: Internet Time

    Internet Time The Internet Time option under Management menu bar configures the Modem’s time. To automatically synchronize with Internet Time servers, tick the corresponding box displayed on the screen. Then click Save/Apply.

  • Page 95: Access Control

    Access Control The Access Control option under Management menu bar configures the access-related parameters, including three parts: Services, IP Address, and Passwords.

  • Page 96: Services

    9.5.1 Services The Services option limits or opens the access services over the LAN or WAN. These services are provided FTP, HTTP, ICMP, SNMP, SSH (Security Socket Share), TELNET, and TFTP. Enable the service by checking the item in the corresponding checkbox, and then click Save/Apply.

  • Page 97: Access Ip Addresses

    9.5.2 Access IP Addresses The IP Addresses option limits the access by IP address. If the Access Control Mode is enabled, only the allowed IP addresses can access the router. Before you enable it, configure the IP addresses by clicking the Add button. Enter the IP address and click Apply to allow the PC with this IP address managing the DSL Router.

  • Page 98: Passwords

    9.5.3 Passwords The Passwords option configures the access passwords for the router. Access to your DSL router is controlled through three user accounts: root, support, and user. “root” has unrestricted access to change and view configuration of your DSL Router. "support"...

  • Page 99: Update Software

    Update software The Update Software screen allows you to obtain an updated software image file from your ISP. Manual software upgrades from a locally stored file can be performed using the following screen. Step 1: Obtain an updated software image file from your ISP. Step 2: Enter the path to the image file location in the box below or click the Browse button to locate the image file.

  • Page 100: Save And Reboot

    Save and Reboot The Save/Reboot options saving the configurations and reboot the router. Close the DSL Router Configuration window and wait for 2 minutes before reopening your web browser. If necessary, reconfigure your PC's IP address to match your new configuration.

  • Page 101: Appendix A: Firewall

    Appendix A: Firewall Stateful Packet Inspection Refers to an architecture, where the firewall keeps track of packets on each connection traversing all its interfaces and makes sure they are valid. This is in contrast to static packet filtering which only examines a packet based on the information in the packet header.
  • Page 102 Destination Port: This can take on either a single port number or a range of port numbers. Packets having a destination port equal to this value or falling within the range of port numbers(portX : portY) will be dropped. Examples: Filter Name : Out_Filter1 Protocol...
  • Page 103 Protocol: Can take on any values from: TCP/UDP, TCP, UDP or ICMP Source IP Address/Source Subnet Mask: Packets with the particular "Source IP Address/Source Subnet Mask" combination will be accepted. Source Port: This can take on either a single port number or a range of port numbers.
  • Page 104 Filter Name : In_Filter2 Protocol : UDP Source Address : 210.168.219.45 Source Subnet Mask : 255.255.0.0 Source Port : 5060:6060 Dest. Address : 192.168.1.45 Dest. Sub. Mask : 255.255.255.0 Dest. Port : 6060:7070 This rule will ACCEPT all UDP packets coming from WAN interface mer_0_35/nas_0_35 with IP Address/Sub.Mask 210.168.219.45/16 and a source port in the range of 5060 to 6060, destined to 192.168.1.45/24 and a destination port in the range of 6060 to 7070.
  • Page 105 Source MAC Address: Of the form, XX:XX:XX:XX:XX:XX. Frames with this particular source address will be Forwarded/Dropped depending on whether the Global Policy is Blocked/Forwarded. Frame Direction: LAN <=> WAN --> All Frames coming/going to/from LAN or to/from WAN. WAN => LAN --> All Frames coming from WAN destined to LAN. LAN =>...
  • Page 106 Addition of this rule forwards all PPPoE frames going from WAN-side to LAN-side with a Dest. MAC Addr. of 00:12:34:56:78:90 and Source MAC Addr. of 00:34:12:78:90:56 on the br_0_34 WAN interface. All other frames on this interface are dropped. Daytime Parental Control This feature restricts access of a selected LAN device to an outside Network through the router, as per chosen days of the week and the chosen times.

  • Page 107: Appendix B: Pin Assignments

    Appendix B: Pin Assignments Console (RJ45) Definition Definition Line port (RJ11) Definition Definition ADSL_TIP ADSL_RING Pin Assignments of the RJ11 Port LAN Port (RJ45) Definition Definition Transmit data+ Transmit data- Receive data- Receive data+ Pin assignments of the LAN Port...

  • Page 108: Appendix C: Specifications

    Appendix C: Specifications Rear Panel RJ-11 X1 for ADSL, RJ-45 X 4 for LAN, Reset Button X 1, Power Jack X 1, Power switch X 1, Console (RJ45) X 1 ADSL Standard ANSI T1.413 Issue 2, ITU-T G.992.1, G.992.2 , G.992.3, G.994.1 G.992.5 (ADSL2+) Downstream : 24 Mbps Upstream : 1.3 Mbps...
  • Page 109 Bridge Functions Transparent bridging and learning IEEE 802.1d VLAN support Spanning Tree Algorithm IGMP Proxy/Snooping Routing Functions Static route, RIP, and RIPv2, NAT/PAT, DHCP Server/DHCP Relay, DNS Proxy, Security Functions Authentication protocols PAP, CHAP, TCP/IP/Port filtering rules, Port triggering/Forwarding, Packet and MAC address filtering, access control, SSH Application Passthrough PPTP, L2TP, IPSec, VoIP, Yahoo messenger, ICQ, RealPlayer, NetMeeting, MSN,...

  • Page 110: Appendix D: Ssh Client

    Appendix D: SSH Client Linux OS comes with ssh client. MicroSoft Windows does not have ssh client but there is a public domain one “putty” that you can download. http://www.chiark.greenend.org.uk/~sgtatham/putty/download.html To access the router using Linux ssh client: From LAN: Use the router WEB UI to enable SSH access from LAN. (default is enabled) type: ssh -l admin 192.168.1.1 From WAN: In the router, use WEB UI to enable SSH access from WAN.

This manual is also suitable for:

Ct-5371

Table of Contents