Related Manuals for Ricoh FS-108R
Summary of Contents for Ricoh FS-108R
- Page 1 Finisher (FS-108R) User’s Guide © 2007 Ricoh Corporation 5 Dedrick Place West Caldwell, NJ 07006 January 2007 N905437B...
- Page 2 © 2007 Ricoh Corporation. All rights reserved. No part of this document may be reproduced without the expressed permission of Ricoh Corporation. The material in this document is for informational purposes and is subject to change without notice. Ricoh Corporation assumes no responsibility for errors or omissions in this document.
- Page 3 Revisions Revision Page No. (Contents) Date Original Release April 2006 Generic Version; Add rev history page, copyright page updated January 2007...
-
Page 4: Table Of Contents
Contents Chapter 1. Introduction ..........1-1 1.1. -
Page 5: Chapter 1. Introduction
Chapter 1. Introduction 1.1. Finisher Configuration 1.1.1. External View of the Finisher The figure below shows an external view of the finisher and descriptions of the main parts. f f f f f f f Finisher F i n i s h e r l l l l 3. -
Page 6: Opening The Finisher
1.1.2. Opening the Finisher Front Cover Open the finisher front cover according to the following figure. F i n i s h e r Finisher Front Cover... -
Page 7: Internal View Of The Finisher
1.1.3. Internal View of the Finisher The following figure shows an internal view of the finisher with the front cover open. Sub Tray Main Tray 2. Stapler Unit 1. Stacker Unit (1) Staple F (2) Staple R Operator’s Side Staple Cartridge... - Page 8 1. Stacker Unit Clear stacked paper when the Operator’s Panel of the printer indicates. 2. Stapler Unit (1) Staple F Replace the staple cartridge in the Staple F on the opera- tor’s side. (2) Staple R Replace the staple cartridge in the Staple R on the oppo- site side of the operator’s.
-
Page 9: Chapter 2. General Information
Chapter 2. General Information 2.1. Powering on the Finisher If your Finisher is connected to a DDP 70/92, turn the finisher on and off using the switch on the printer. The mark on the switch represents the binary characters “O” for off and “I”... -
Page 11: Chapter 3. Replacing Consumables
Chapter 3. Replacing Consumables 3.1. When to Replace Consumables The Operator’s Panel on the printer displays a message informing you when a supply needs to be replaced. However, the following item will help you anticipate when to replace consumables. Consumable Replace every... -
Page 12: Replacing The Staple Cartridge
3.2. Replacing the Staple Cartridge Replace the staple cartridge when LOW STAPLE (R) or LOW STAPLE (F) is displayed on the Operator’s Panel. 1. Open the finisher front cover. 2. Pull out the stacker unit by holding the stacker unit handle. - Page 13 5. Insert the new cartridge into the housing. Note: Do not remove the remaining staples inside the housing; otherwise, the first sheet output after the replenishment will not be stapled. 6. Insert the cartridge housing while sliding it along the stapler rail, then push in and down to secure it in place.
-
Page 15: Chapter 4. Troubleshooting
Chapter 4. Troubleshooting 4.1. Clearing Paper Jams The finisher stops when a misfeed occurs and PAPER JAM is displayed on the Oper- ator’s Panel of the printer. Follow the steps below to clear paper from the finisher. Move the blue tab and remove paper. Turn the blue knob, move the blue tab, then remove paper. -
Page 16: Clearing Wedged Staples
4.2. Clearing Wedged Staples Follow the steps below to clear wedged staples. Pull out the stacker unit by holding the stacker unit handle. Pull up the cartridge housing, then remove it while sliding it along the stapler rail. Pull the lever of cartridge, then open the cover. Remove the wedged staples. - Page 17 Return the Cover of cartridge to its original position. Insert the Cartridge housing while it along the stapler rail, then push in and down to secure it in place. Return the stacker Unit to its original position. After removing the wedged staples, staples do not come out from the stapler for several times, then execute the TEST PRINT of staple mode till staple appears on the paper.
-
Page 19: Chapter 5. Others
Chapter 5. Others 5.1. Extend the Tray Extend the Main Tray and the Sub Tray, Main Tray Sub Tray when the length of the printed paper is 9 inches or more. 5.2. Cancel of Staple Job When the staple job is canceled, the paper of this job is delivered to the Main Tray without staple.