Page 1
!Insta"ation IOas S"0e'n nstructlons JGSP28 Questions? Call 800.GE.CARES (800.432.2737) or Visit our Website at: www.GEAppliances.com IN THE COMMONWEALTH PARTS INCLUDED MASSACHUSETTS: • This product must be installed by a licensed plumber or gas fitter. • When using ball-type gas shut-off...
Installation Instructions IMPORTANT SAFETY INSTRUCTIONS FOR YOUR SAFETY: This range has been design certified UNDERWRITERS LABORATORIES. You'll find safety precautions in your Owner's Manual. Read them carefully. • Installation of this range must conform with local codes or in the absence of local codes with the National...
Page 3
mnstaliation mnstructions ELECTRICAL REQUIRMENTS ANTI-TIP DEVICE This appliance must be supplied with WARNING -To reduce therisk proper voltage and frequency and connected of tipping, the appliance must be secured to an individual, properly grounded branch by properly installed Anti-Tip bracket packed circuit, protected...
To obtain Kits: a. Visit GE Web Site (See page 1) b. Call GE Answer Center (See page 1) c. Contact Dealer [_] CAREFULLY, TILT RANGE TO ACCESS RANGE LEVELING...
Page 5
Installation Instructions REMOVE THE DOOR JF REMOVE THE DOOR NECESSARY (cont.) Door removam is not a requirement LIFT OFF DOOR installation of the product, but is an added Lift door up and out until the hinge arms convenience. To remove the door: clear the slots.
Page 6
mnstaliation mnstructions PRE-INSTALLATION CHECKLIST (CONT.) [-_ PRE-INSTALLATION CUTOUT AND REQUIRED CLEARANCES If cabinets are placed less than 30" above the range, OWRALLOEPT"'_I see Alternate Construction, Step 19t, on page 16. I.._0-_/o. NOTE: Product meets ANSI Z21.1 requirements for 0" clearance to back and side walls below...
mnstaliation mnstructions ELECTRICAL CONNECTIONS INSTALLATIONmELECTRICAL CONNECTIONS Because of potential safety hazards under certain conditions, we strongly recommend against the use of an extension cord. However, if you still elect to use an extension cord, it is absolutely necessary that it is a UL listed 3-wire grounding-type...
Installation Instructions GAS CONNECTIONS MAKING THE CONNECTIONS MAKING THE CONNECTIONS (cont.} Install 1/2"flare union adaptor to the 1/2" NPT elbow on pressure regulator. Connect flexible appliance connector flare union. Move range into approximate position and connect flexible connector to gas Install a manual shut-off valve in the gas...
Installation Instructions INSTALL THE RANGE r_ INSTALL THE ANTI-TIP BRACKET iNSTALL THE ANTi-TiP BRACKET (cont.) LOCATE THE BRACKET a, Decide whether the bracket will INSTALL THE BRACKET IN WOOD installed on the right or left side of the OR CONCRETE range opening.
Page 10
Installation Instructions INSTALL THE RANGE (CONT.) SUDE {RANGE INTO OPENING SLIDE RANGE INTO OPENING (cont.) Position the range in front of the cabinet opening. Plug the range cord into the receptacle. Locate the cord in the back of the range Make sure that the cooktop edges that in a manner...
Page 11
Installation Instructions r_] REPLACE THE OVEN DOOR REPLACE THE STORAGE DRAWER NOTE: The oven door is heavv. You mav need help lifting the door high enough to slide it Place the drawer rail on the guides. into the hinge stots. Do not lift the door Push the drawer in until it stops.
Page 12
Installation Instructions INSTALL THE RANGE (CONT.) r_] COOKTOP BURNERS r_l COOKTOP BURNERS (cont.) ASSEMBLE THE BURNERS (cont.) ASSEMBLE THE BURNERS c. Place the matching size caps onto the heads. CAUTION: The electrode of the Make sure that the heads and caps are spark igniter is exposed.
Try each valve separately until all burners proper length, call GE Service. have been checked. 1/2" to 3/4" COOKTOP BURNER Flames should circle burner Burners should be checked frequently. WARNING: Ifyou...
nstaJiation nstructions INSTALL THE RANGE (CONT.) ADJUST THE AIR SHUTTER BAKE AND BROIL BURNERS BAKE BURNER If the bake and/or broil burners have lifting "lazy" (floating) flames or you have a yellow 1. Remove the orifice fitting cover. flame, perform the following procedures: 2.
Page 15
mnstaliation mnstructions When the trim is set in the proper position, ALTERNATE CONSTRUCTION tighten the 2 mounting screws. The top of PREPARATION the trim should be located below the cooktop edge to prevent pots, pans and skillets from OPTIONAL MAINTOP FILLER OR BACKGUARD damaging...
Page 16
nstaJiation nstructions INSTALL THE RANGE (CONT.) Please see L.P. conversion instructions ALTERNATE CONSTRUCTION supplied with this range when L.P. Gas PREPARATION (cont.) is used. FOR CABINET OPENINGS NOTE: Instructions are mounted APPROXIMATELY 30-3/8" regulator bracket. If range is installed in cabinet opening approximately 30-3/8", the Vertical Side Trim Kit (JXS86XX)