Premium 24/22/16-input 4/2 and 2/2-bus mixer with xenyx mic preamps & compressors, british eqs, 24-bit multi-fx processor and usb/audio interface (16 pages)
XENYX XL1600/XL2400/XL3200 Read these instructions. Important Safety Instructions Keep these instructions. Heed all warnings. Follow all instructions. Do not use this apparatus near water. Clean only with dry cloth. Do not block any ventilation openings. Install in accor- This symbol, wherever it appears, alerts you to the dance with the manufacturer’s instructions.
Because we know that your success is our success, too! 5.3.1 MAIN A section .............12 I would like to thank everyone who has made the XENYX pos- 5.4 Level meters .............. 12 sible. You have all made your own personal contributions, from 5.5 Subgroups ..............
Shipment ment packaging (Global Contact Information/European Contact Your XENYX was carefully packed at the factory, and the pack- Information). Should your country not be listed, please contact the distributor nearest you. A list of distributors can be found in the aging was designed to protect the unit from damage caused by support area of our website (www.behringer.com).
XENYX XL1600/XL2400/XL3200 Installation Rack mounting (XL1600 only) The packaging of your XL1600 contains two 19" rack mounts that can be fastened to the side panels of the console. Before you can attach the rack mounts to the mixing console, you need to remove the screws holding the left and right side panels.
When installing the product, ensure that the plug is easily Phantom power is used for operating a capacitor microphone. A accessible. If mounting in a rack (XL1600 only), ensure that the control LED lights up next to the switch when the phantom power mains can be easily disconnected by a plug pull or by an all-pole supply is active.
XENYX XL1600/XL2400/XL3200 Stereo inputs CD/tape connectors LINE L (MONO), LINE R The stereo channels consist of two line inputs (¼" The CD/TAPE input connectors are used to hook up jacks), one for the left and one for the right channel.
XENYX XL1600/XL2400/XL3200 5.1.1 FX, MON, AUX send paths Control elements The send paths FX, MON and AUX allow you to tap This chapter describes the various control elements of your mixing the signals of one or more channels and route them console.
The routing switch routes the signal to the respective subgroup and right input signals before they are routed to the stereo main or the main mix or both. The XENYX features 4 subgroups. The mix bus (or to two subgroups).
XENYX XL1600/XL2400/XL3200 Main section Subgroups The XENYX pro- 5.3.1 MAIN A section vides 4 subgroups which allow you to BAL(ANCE) feed multiple chan- The BAL(ANCE) control adjusts the mix of the nels to mono or left and right output signal before both signals are stereo mixdowns.
5.6.1 Talkback MAIN B section The talkback function of the XENYX allows you to The mixer sum can also be routed to the MAIN B output which communicate with people on stage. The talkback may be connected to a separate power amplifier. This way the signal can be routed to the different bus outputs.
We wish to be absolutely clear that BEHRINGER cannot output signals. be held responsible after you start disassembling your XENYX. If you make much of your warranty privileges, SEND think again. The SEND faders control the output level of the monitor buses.
XENYX XL1600/XL2400/XL3200 4. Damage/defects caused by the following conditions are not covered Warranty by this warranty: improper handling, neglect or failure to operate the unit in compli- § 1 Other warranty rights and national law ance with the instructions given in BEHRINGER user or service manuals.
Suite 200 Bothell, WA 98011, Phone/Fax No.: Phone: +1 425 672 0816 Fax: +1 425 673 7647 hereby declares that the product XENYX XL1600 XENYX XL2400 XENYX XL3200 complies with the FCC rules as mentioned in the following paragraph: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.