Automatic Oven Timer - GE JBP29G Use And Care & Installation Manual

Automatic Oven Thner
The oven timer will automatically
start and stop your oven cooking or
self-cleaning operation for you
For automatic oven cooking:
1. Push COOK TIME button.
2, Turn SET knob to set length of
baking ti_me_
3. Push BAKE button.
4. Turn SET knob to set desired
temperature,,
When cook time is reached, the
End-of-Cycle Tone will sound and
the oven will turn off
During automatic cooking:
o You can push the S'IOP TIME
button to fred out when the End-of-
Cycle Tone wil! sound and the oven
will turn off,
o You can push the CLOCK button
to display time of day without
cancelling the oven operation.
To Delay Starthlg an
Automatic Oven Operation
If a delayed cooking operation
is desired:
1. Push COOK TIME button_
2. Set length ofbakJng time with
SET [:nob.
3. Push STOP TIME button.
4. Turn SET knob to time of day
when baking should be completed.
Do not set a stop time that is tess
than the length of cooking time
plus the current time of day.
5. Push BAKE button°
6. Turn SET knob to desired
temperature.
When stop time is reached, the
End-of-Cycle Tone will sound and
the oven will turn off.
Caution: Never let food sit in the
oven for more than 4 hours before
cooking starts. Room temperature
is ideal for the growth of hazmful
bacteria_ Be sure oven light is off
because heat from the bulb will
speed bacteria growth
Note: You can push the STOP
TIME button to find out when the
oven will turn off, Push and hold
the COOK TIME button to find out
when the oven will turn on_
If a delayed self-cleaning oven
operation is desired, see page 26.
How to Change
a Program
When a function has been
entered, you can recall what has
been programmed by pushing
the corresponding function
button° The messages in the
display show you which function
is currently being displayed.
While the function is displayed,
you can change it with the SET
knob° You can change any
programmed function at any
time°
Tones
End-of-Cycle Tone (3 long beeps--
one second on, one second off):
shows that a timed oven operation
has reached STOP TIME or that
the Minute/Second Timer has
counted down.
Attention Tone (series of short
beeps, 1/4-second on, 1/4-second
off, until proper response is given):
will sound if oven has only been
partially programmed. For example,
if you have selected a cook time but
no temperature, you will hear the
Attention Tone until you select a
temperature or push CANCEL.
Notification Tone (single, one-
second beep): indicates oven has
stabilized at selected temperature_
Key Tone (single, 1/10-second
beep): sounds when any button
is pushed.
Function Error Tone (series of
very rapid beeps, t/8-second on,
U4-second off): display will show a
failure code_ Cancel Function Error
Tone by pushing the CANCEL
button. If the Function Error Tone
starts again (after about 15 seconds),
call for service. Disconnect the range
electrical supply to stop the tone.
If the function error occurred
while you were programming the
Electronic Control, push the
CANCEL button and try again.
To Cancel the Tone,., If you don't
want an audible tone when you push
a button, you can eliminate the Key
Tone by pushing and holding the
CANCEL button until you hear a
short beep (in approximately two
seconds). To activate the tone again,
push and hold the CANCEL button
once more until you he_ a short
beep. Cancelling or activating the
tone should only be done when there
is no oven operation programmed_
Pushing the CANCEL button wilt
clear all functions except the Clock
and Minute/Second Timer.
17