GE CGS980 Owner's Manual & Installation Instructions page 33

Burner cad is Burner cad is NOT
properS, searea, properly searea.
Front
right Burlier
Burnercau (
_Ul er nead _,_._>_J
Electrode __
Burner b ase __/"
Make sure the hole in the burner
head is positioned over the electrode
and that the burner head is fully
inserted inside the burner base.
A smaegap between the base and
head is normal
C"on[ left burner, BaCK gl I ourne/
anu BaCKeft bun/or
JT
rleBB]e Of
UI1ClOg I118
sman ROle [11
[lle ournfi
RsarJ.
Flec_roue
Make sure the s!ot in the bumer head
is positioned over the electrode.
Holein
burner
The ova! burner head/cap assembly is
removable. Simply lift it off the range
for cleaning. Use a sewing needle or
twist4ie to unclog the small hole in the
burner heads.
Burner Caps and Heads
Before removing the burner caps and heads, remember
their size and location. Replace them in the same location
after cleaning.
NOTE: Do not use steel wool or
scouring powders
t o clean
the burner
parts.
Burnercaps
i,ift ott when ecol. Wash burner caps in hot,
soapy water and rinse _ith clean _ ater. You may
scour _._ith a plastic scouring, l)ad to relno_,e
bm'ned-on tbod partkies.
BurnerHeadsand Oval(Center)Burner
Head/CapAssembly
The burner heads a ndtheoval b urner head/cap assembly
are removable. Simply lift them off the range for cleaning.
For proper ignition, make sure the small bole
in fl_e section that fits o\er the electrode is kept
open. A sewing needle
or wix_ t\_ist-tie works
well to unclog it.
The slitsintheburner heads m ust b ekept c lean at all
times for an even, unhampered flame.
Clogged or dirty burner ports or electrodes _dll
not allow the burner to operate properl}.
A W spill on or around an electrode nmst
be carefldlv cleaned. Take care to not hit an
electrode with an}thing hard or it could be
damaged.
Clean the burner heads routinel 5 especially after
bad spillo_ers, which could clog the openings.
I,ifl off when cool.
To remo\e burned-on
tood, soak the burner
beads in a solution of mild liquid dewrgent and
hot _lter tot 20-30 minutes. For more stubborn
stains, use a toothbrush.
After cleaning
Before putting the burner caps, beads and oval
head/cap assembly back, shake out excess _ter
and then dry them thoroughly b} setting in a
_m'rn oven for 30 minums.
ge.com
Replacement
BurnerHeads
Replace burner beads o_er the electrodes
on
the eooktop, in the eon'ect locatkms according
to their size. There is one small, one medim-n,
one exu'a large and one dual flmne extra large
burner head.
Make sure the slot (on fl'ont left, back right and
back left heads) and the hole (fl'ont ngbt bead)
in the burner head is positioned over file
electrode.
Burnerhead H_
_ Burne[b_ad (
Electrode_1_ Electrode _ ):
_-'_"(_}SI_ t
Front l eft, backright Front righthead
andbackleft heads
Oval(Center)BurnerHead/CapAssembly
Replace the oval ((enter) head/cap assembly
over the electrode
on the cooktop.
Ovalheadand cap Make Suretbe slot in tbe
assembly
burner head is positioned
over the electrode.
* ®
FrontOfrange Electrode
Caps
Replace the matching size caps onto the burner
bases or beads.
Frontof range largecap
Make sure that the heads and caps are replaced
in the con'ect locations.
33
i::::::2i;;iii
i;::::::!iii}ii
g
g