Table of Contents
Advertisement
Quick Links
20 Gallon Parts Washer
set uP and oPeratinG instructions
distributed exclusively by harbor Freight tools
Visit our website at: http://www.harborfreight.com
read this material before using this product.
Failure to do so can result in serious injury.
saVe this manual.
©
Copyright
2008 by Harbor Freight Tools
contained herein may be reproduced in any shape or form without the express written consent of
Harbor Freight Tools. Diagrams within this manual may not be drawn proportionally. Due to continuing
improvements, actual product may differ slightly from the product described herein. Tools required for
assembly and service may not be included.
For technical questions or replacement parts, please call 1-800-444-3353.
With Wheels
3491 Mission Oaks Blvd., Camarillo, CA 93011
®
. All rights reserved. No portion of this manual or any artwork
98332
®
.
Advertisement
Table of Contents
Related Manuals for Chicago Electric 98332
Summary of Contents for Chicago Electric 98332
- Page 1 20 Gallon Parts Washer With Wheels 98332 set uP and oPeratinG instructions ® distributed exclusively by harbor Freight tools 3491 Mission Oaks Blvd., Camarillo, CA 93011 Visit our website at: http://www.harborfreight.com read this material before using this product. Failure to do so can result in serious injury. saVe this manual.
-
Page 2: Important Safety Information
saVe this manual notice is used to address practices Keep this manual for the safety warn- not related to personal injury. ings and precautions, assembly, operat- caution, without ing, inspection, maintenance and cleaning the safety alert procedures. Write the product’s serial symbol, is used to address number in the back of the manual near the practices not related to... - Page 3 avoid body contact with grounded ate conditions will reduce personal surfaces such as pipes, radiators, injuries. ranges and refrigerators. There is Prevent unintentional starting. an increased risk of electric shock if ensure the switch is in the off-po- your body is grounded. sition before connecting to power do not expose power tools to rain source and/or battery pack, pick-...
- Page 4 Power tool use and care service do not force the power tool. use have your power tool serviced by the correct power tool for your ap- a qualified repair person using plication. The correct power tool will only identical replacement parts. do the job better and safer at the rate This will ensure that the safety of the for which it was designed.
- Page 5 approved safety equipment, such as manual cannot cover all possible con- those dust masks that are specially ditions and situations that may occur. designed to filter out microscopic It must be understood by the operator particles. (California Health & Safety that common sense and caution are Code §...
-
Page 6: Extension Cords
Grounded tools: tools with three double insulated tools: tools Prong Plugs with two Prong Plugs Tools marked “Double Insulated” do Tools marked with “Grounding Re- not require grounding. They have quired” have a three wire cord and a special double insulation system three prong grounding plug. - Page 7 The smaller the gauge number of the recommended minimum Wire wire, the greater the capacity of the GauGe For eXtension cords* cord. For example, a 14 gauge cord (120/240 Volt) can carry a higher current than a 16 eXtension cord namePlate gauge cord.
-
Page 8: Specifications
sPeciFications to PreVent serious injurY From accidental Electrical Requirements 120 V~ / 60 Hz oPeration: Fluid Capacity 20 Gallons turn the Power switch of the 5.28 Gallons per Maximum Flow tool to its “oFF” position and Minute unplug the tool from its Fusible Link Tested at 185°... -
Page 9: Operating Instructions
Functions tool set up When used with an appropriate sol- to PreVent vent (not included) this Parts Washer serious injurY is useful for cleaning mechanical From accidental parts of dirt, grease and other con- oPeration: taminants. turn the Power switch of the tool to its “oFF”... -
Page 10: Maintenance And Servicing
Appropriate brushes, grips, rags, To prevent accidents, turn off the tool etc. should be provided for effective and disconnect its power supply after cleaning. use. Clean, then store the tool in- doors out of children’s reach. Safe disposal must be provided for any rags or other materials used in maintenance and the cleaning process. - Page 11 aFter use, clean external surfaces After draining the Parts Washer of of the tool with clean cloth. solvent, remove these parts and blow clean with dry compressed air. WarninG! if the supply cord of this power tool is damaged, it must Wipe the components clean and rein- be replaced only by a qualified stall before refilling the Parts Washer...
-
Page 12: Parts List
Parts list Parts list Part description Qty. Part description Qty. Cover Switch Box Work Basket Screw Spring Pan Switch Flexible Pipe Safety Plate Elbow Seat Work Shelf Elbow Body Plastic Washer Spring Washer Spigot Seal Ring O-ring Pump Drain Plug Shelf Spring Washer Toothed Washer... -
Page 13: Assembly Diagram
assemBlY diaGram record Product’s serial number here: note: If product has no serial number, record month and year of purchase instead. note: Some parts are listed and shown for illustration purposes only, and are not avail- able individually as replacement parts. SKU 98332 For technical questions, please call 1-800-444-3353. -
Page 14: Limited 90-Day Warranty
limited 90 daY WarrantY Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards, and warrants to the original purchaser that this prod- uct is free from defects in materials and workmanship for the period of 90 days from the date of purchase.