Ricoh Pro C900 Replacement Manual
  1. Manuals
  2. Brands
  3. Ricoh Manuals
  4. All in One Printer
  5. Pro C900
  6. Replacement manual

Ricoh Pro C900 Replacement Manual

Tcru
Hide thumbs Also See for Pro C900:
Table of Contents

Advertisement

Quick Links

See also: Installation Manual
Adjustment Item Menu Guide: TCRU

Model Name:

Pro C900S/Pro C900
Read this manual carefully before using this machine and keep it handy for future reference.
1

Advertisement

Table of Contents
loading

Related Manuals for Ricoh Pro C900

Summary of Contents for Ricoh Pro C900

  • Page 1: Model Name

    Adjustment Item Menu Guide: TCRU Model Name: Pro C900S/Pro C900 Read this manual carefully before using this machine and keep it handy for future reference.
  • Page 2 Replacement Guide: TCRU Model Name: Pro C900S/Pro C900...

  • Page 3: Conventions Used In This Manual

    CONVENTIONS USED IN THIS MANUAL CAUTIONS, NOTES, ETC. The following headings provide important information that you must read: WARNING Failure to follow the information could result in serious injury or death. CAUTION Follow the information to ensure safe operation and avoid minor injuries. Important: •...
  • Page 4 Power Plug and Power Cord Always make sure that the power plug is fully completely into the wall outlet. A partially inserted plug could lead to heat generation (due to a power surge caused by high resistance) that can result in fire and other problems. Always check the power plug and make sure that it is free of dust and lint.
  • Page 5 WARNING • Protect the machine from dampness or wet weather, such as rain and snow. • Unplug the power cord from the wall outlet before moving the machine. While moving the machine, take care that the power cord is not damaged under the machine. •...

  • Page 6: Table Of Contents

    Table of Contents CONVENTIONS USED IN THIS MANUAL............2 GENERAL SAFETY INSTRUCTIONS..............2 1. BEFORE YOU BEGIN… ..............6 2. COMMON PROCEDURES.............10 2.1 SWITCH THE MACHINE OFF BEFORE BEGINNING ANY PROCEDURE!10 2.2 OPENING THE TCRU DISPLAY..............12 2.3 REMOVING THE FRONT TOP COVER............15 2.4 REATTACHING THE FRONT TOP COVER ..........

  • Page 7: Before You Begin

    1. BEFORE YOU BEGIN… This manual is only operators who have received training in the procedures shown in this manual. General users are not to perform the procedures shown in this manual. • Never perform any procedure in this manual if you have not received proper training.

  • Page 8: Names Of Components

    NAMES OF COMPONENTS RPG062S 1. Toner hopper cover 2. Front top cover 3. Inner cover 4. Left front cover 5. Right front cover 6. Control panel Parts, Screw Color Codes • Handles and levers colored purple indicate where you should pull or lift a component or part to move or remove it.
  • Page 9 CONTROL PANEL (Pro C900) 1. User Tools 2. Counter 3. Printer function/[fierydriven] 4. ./* key 5. Enter key 6. Clear key 7. On indicator 8. Operation Switch 9. Number keys...
  • Page 10 CONTROL PANEL (Pro C900S) 1. User Tools 2. Counter 3. ./* key 4. Enter key 5. Clear key 6. On indicator 7. Operation Switch 8. Number keys 9. Program...

  • Page 11: Common Procedures

    2. COMMON PROCEDURES 2.1 SWITCH THE MACHINE OFF BEFORE BEGINNING ANY PROCEDURE! WARNING • To prevent electrical shock, turn off the main power switch and disconnect the ground wire from the machine and fixing heater. Preparation Before performing any procedure shown in this manual, always do the following: 1.
  • Page 12 SYSTEM AUTO RESET TIMER (TIMER SETTINGS) The System Reset setting automatically switches the screen to that of the function specified in Function Priority if the machine is left idle for a specified period. • On • Off The setting should be “Off”. If you select "On", you can specify how long the machine waits before switching the screen.

  • Page 13: Opening The Tcru Display

    2.2 OPENING THE TCRU DISPLAY Overview • When installed, the TCRU SD card enables an LCD display application specially designed for use with TCRU machines. • The TCRU SD card can be installed on TCRU machines only. It will not function with other models.
  • Page 14 After connecting the ground leakage circuit breaker to the machine and fixing heater, turn the machine on and wait for it to warm up. For users of Pro C900, press the Printer function/[fierydriven] key on the control panel to display the Main Menu.
  • Page 15 TCRU MENU SUMMARY This section explains the functions of the buttons on the TCRU Menu. The menu displayed under each button in the TCRU menu The function menu is shown below. Note: The following is based on the charge corona unit function menu. [Display PM Counter] buttons There is a [Display PM Counter] button for each unit.

  • Page 16: Removing The Front Top Cover

    2.3 REMOVING THE FRONT TOP COVER Procedure 1. Open the left (2) and right (1) front covers. RPG020S 2. Open the toner hopper cover (1). RPG003S Remove the two screws at (1) and (2) by hand. Note: Use a coin to turn the screws if they are too tight to turn by hand. Lift up the front top cover (3) and remove it.

  • Page 17: Reattaching The Front Top Cover

    2.4 REATTACHING THE FRONT TOP COVER Procedure 1. Hold the front top cover. 2. Align the two tabs (1) on the bottom of the front top cover with the two cutouts (2) on the frame of the machine, and then hook the front top cover. 3.

  • Page 18: Charge Corona Unit

    3. CHARGE CORONA UNIT 3.1 REMOVING THE CHARGE CORONA UNIT What You Need • Accessory hex driver provided with the machine. • Newspaper or other paper covering a nearby flat surface on which you can place removed components. WARNING • To prevent electrical shock, switch off the main power switch and disconnect the ground wire from the machine and fixing heater.
  • Page 19 Procedure Open the left and right front covers. Remove the front top cover (See " REMOVING THE FRONT TOP COVER") Hold the charge corona unit (1) with the lock lever (2) pressed down. RPG022 RPG023 4. Carefully pull the charge corona unit (1) toward you. RPG024 5.
  • Page 20 Important: To protect the charge corona unit from fingerprints, scratches, and dust: • Always hold the charge corona unit (1) with both hands. • Never touch the wire mesh (2) below. • Never allow anything to touch the wire mesh while the charge corona unit is outside the machine.

  • Page 21: Reinstalling The Charge Corona Unit

    3.2 REINSTALLING THE CHARGE CORONA UNIT Important: To protect the charge corona unit from fingerprints, scratches, and dust: • Never touch the wire mesh on the underside of the charge corona unit. • Never allow anything to touch the wire mesh while the charge corona unit is outside the machine.
  • Page 22 Press the [Reset PM Counter] button of the item that is the corresponding color. If a confirmation message appears, press the [Continue] button. Note: The counter will be reset. When the counter is reset, press the [Confirm] button.

  • Page 23: Drum Cleaning Unit

    4. DRUM CLEANING UNIT 4.1 REMOVING THE DRUM CLEANING UNIT What You Need • Accessory hex driver provided with the machine. • Newspaper or other paper covering a nearby flat surface on which you can place removed components. WARNING • To prevent electrical shock, switch off the main power switch and disconnect the ground wire from the machine and fixing heater.
  • Page 24 4. Remove the inner cover (2) of the development unit drawer. RPG026 5. Loosen the drawer stop knob (1) by turning it counterclockwise, and then remove it. RPG027 6. Holding the purple handle (1), carefully pull out the development unit drawer. RPG028 Important: Do not leave the development unit drawer open for a long time.
  • Page 25 7. Turn the drum cleaning unit lock lever (1) counterclockwise. RPG029 8. Grasping both sides (1) of the drum cleaning unit as shown, lift the drum cleaning unit (2) straight up. RPG007S 9. To avoid spilling toner, always carry the drum cleaning unit level with the exposed roller (1) facing up (not down).

  • Page 26: Reinstalling The Drum Cleaning Unit

    4.2 REINSTALLING THE DRUM CLEANING UNIT Procedure Note: If you want to replace the drum unit with the drum cleaning unit, see "DRUM UNIT". 1. Check the drum cleaning unit direction for reinstalling. • The waste toner collection pipe (1) should be at rear side. RPG018S 2.
  • Page 27 4. Gently and firmly push the purple handle (2) into the machine until the drawer can go no further and locks into place. RPG032 Important: Do not pinch the harnesses (1) on the frame when pushing the development unit drawer into the machine. RPG036 5.
  • Page 28 Reattach the front top cover and close the toner hopper cover. (See "REATTACHING THE FRONT TOP COVER".) Reconnect the ground leakage circuit breaker for the machine and fixing heater. Press the main power switch to turn the machine on, close the left and right front covers, and then wait for the machine to warm up.

  • Page 29: Drum Unit

    5. DRUM UNIT 5.1 REMOVING THE DRUM UNIT What You Need • Accessory hex driver provided with the machine. • Newspaper or other paper covering a nearby flat surface on which you can place removed components. WARNING • To prevent electrical shock, switch off the main power switch and disconnect the ground wire from the machine and fixing heater.
  • Page 30 Procedure Open the left and right front covers, open the hopper cover, and then remove the front top cover. (See "REMOVING THE FRONT TOP COVER".) Remove the charge corona unit. (See "REMOVING THE CHARGE CORONA UNIT.) Remove the drum cleaning unit. (See "REMOVING THE DRUM CLEANING UNIT".) Turn the drum lock nut (1) counterclockwise, and unlock the drum unit.

  • Page 31: Reinstalling The Drum Unit

    5.2 REINSTALLING THE DRUM UNIT Procedure Important: Never touch the green area of the drum. 1. Set the new drum unit (1) in the development unit drawer, and make sure that the two guides (2) (front) (3) (rear) at the development unit drawer are inserted securely in the grooves (4) (front) (5) (rear) at the drum unit.
  • Page 32 3. Using the powder pad applicator, pat the surface of the drum lightly. RPG019S Important: • Setting powder must cover at least 25% of the surface of the drum to prevent damage to the drum cleaning unit and the drum. •...
  • Page 33 Turn the machine's main power switch to ON, close the left and right front covers, and then wait for the machine to warm up. Open the TCRU Display. (See "OPENING THE TCRU DISPLAY".) Press the [Drum Unit] button. Press the [Reset PM Counter] button of the item that is the corresponding color. If a confirmation message appears, press the [Continue] button.

  • Page 34: Developer

    6. DEVELOPER 6.1 REMOVING THE USED DEVELOPER Overview You can remove the developer from more than one developer unit at a time. Important: Dispose of the developer bottle in accordance with the disposal regulations in your area. What You Need •...
  • Page 35 Procedure Open the left and right front cover, open the toner hopper cover, and then remove the front top cover. (See "REMOVING THE FRONT TOP COVER".) Check that the developer you are preparing is the correct color by looking at the combination of the raised markings (1) on the shutter of the developer bottle.
  • Page 36 6. Push the developer bottle to in the direction of the arrow (1) until it it can go no further and locks into place. RPG054 Open the TCRU display. (See "OPENING THE TCRU DISPLAY".) Press the [Developer] button. Press the [Reset PM Counter Developer:Exhaust] button. If a confirmation message appears, press the [Continue] button.
  • Page 37 13. After removing the developer, press the [Confirm] button, and then, while pressing the lock levers on either side of the developer bottle, carefully pull the bottle toward you. Important: To avoid developer spillage while handling the developer bottle, always keep the developer bottle level.

  • Page 38: Adding New Developer

    16. Attach the seal to the shutter (1) of the developer bottle, as shown. Note: To prevent developer leaking during transport, cover the developer bottle's opening. RPG049 Important: At this point, begin the procedure for adding the new developer. (See "ADDING NEW DEVELOPER")
  • Page 39 6.2 ADDING NEW DEVELOPER Important: Be sure to switch the machine on before beginning this procedure. This procedure requires the machine to be powered. Procedure 1. Check that the developer you are preparing is the correct color by looking at the combination of the raised markings (1) on the shutter of the developer bottle.
  • Page 40 4. Push the developer bottle in the direction of the arrow (1) until it can go no further and locks into place. RPG051 5. Pull the seal (1) completely away. RPG050 Open the TCRU display. (See "OPENING THE TCRU DISPLAY".) Press the [Developer] button.
  • Page 41 11. When the confirmation message appears, press the [Confirm] button, and then, while pressing the lock levers on either side of the developer bottle, carefully pull the bottle toward you. RPG052 Disconnect the developer bottle from the contact on the developer inlet, and then remove it.

  • Page 42: Image Transfer Belt Cleaning Unit

    7. IMAGE TRANSFER BELT CLEANING UNIT TRANSFER BELT CLEANING REMOVING THE IMAGE UNIT What You Need • Accessory hex driver provided with machine. • Newspaper or other paper covering a nearby flat surface on which you can place removed components. WARNING •...
  • Page 43 Procedure Open the left and right front covers. Remove the two black screws (1) on the inner cover (2) for the image transfer belt cleaning unit using the hex driver. Remove the inner cover (2). Note: To remove the inner cover, pull it out and slightly upward. RPG044 Remove the black screw (1) on the image transfer belt cleaning unit using the hex driver.
  • Page 44 6. Using the handle (1), carefully pull the image transfer belt cleaning unit toward you until it can go no further. RPG039 7. While pressing down the lock tab (1), carefully pull out the image transfer belt cleaning unit. RPG058 Important: To avoid toner spillage while handling the image transfer belt cleaning unit, always keep the image transfer belt cleaning unit level.

  • Page 45: Installing The Image Transfer Belt Cleaning Unit

    7.2 INSTALLING THE IMAGE TRANSFER BELT CLEANING UNIT Procedure 1. While holding the image transfer belt cleaning unit with both hands, set the image transfer belt cleaning unit (1) on its rails (2), and then carefully push it in until it can go no further. RPG041 RPG040 Fasten the black screw (1) on the image transfer belt cleaning unit using the...
  • Page 46 11. Rotate the cleaning blade contact lever (2) counterclockwise. RPG037 Reattach the inner cover and then fasten the two black screws on the inner cover of the image transfer belt cleaning unit using the hex driver. (See "REMOVING THE IMAGE TRANSFER BELT CLEANING UNIT".) Close the left and right front covers.

  • Page 47: Paper Transfer Roller Unit

    8. PAPER TRANSFER ROLLER UNIT 8.1 REMOVING THE PAPER TRANSFER ROLLER UNIT What You Need • Newspaper or other paper covering a nearby flat surface on which you can place removed components. WARNING • To prevent electrical shock, switch off the main power switch and disconnect the ground wire from the machine and fixing heater.
  • Page 48 Using the hex driver, remove the black screw in the rear lock (1), and then slide the rear lock to the rear end. Using the hex driver, remove the black screw in the front lock (2), and then slide the front lock to the front end. RPG065S 5.

  • Page 49: Installing The Paper Transfer Roller Unit

    8.2 INSTALLING THE PAPER TRANSFER ROLLER UNIT Procedure While holding the paper transfer roller unit (1) with both hands, align the stays (2) of the paper transfer roller unit with the shafts of the registration unit drawer, and then set the paper transfer roller unit on the registration unit drawer. Slide the rear lock (3) forward to align it with the shaft screw hole.
  • Page 50 Troubleshooting: TCRU Model Name: Pro C900S/Pro C900...
  • Page 51 Table of Contents 1. BEFORE YOU BEGIN .................3 1.1 GUIDE TO COMPONENTS................3 1.2 ADJUSTMENT: USING THE TCRU SD CARD ..........4 2. TROUBLESHOOTING SERVICE CALL PROBLEMS (SC CODES) ..5 2.1 WHAT ARE SC CODES? ................5 2.2 SC CODE LIST....................5 3.

  • Page 52: Before You Begin

    1. BEFORE YOU BEGIN If the machine will not print, does not print as expected, or exhibits any other problem, find the problem in this manual and troubleshoot accordingly. CAUTION Before you replace any unit: • Always turn the machine off and unplug the power cord from the power source.

  • Page 53: Adjustment: Using The Tcru Sd Card

    2. Turn the main power on, and then wait for the machine to warm up. 3. After the machine has started up, press the Printer function/[fierydriven] key on the control panel for users of Pro C900. For users of Pro C900S, press the [Program] key to display the Main Menu.

  • Page 54: Troubleshooting Service Call Problems (Sc Codes)

    2. TROUBLESHOOTING SERVICE CALL PROBLEMS (SC CODES) 2.1 WHAT ARE SC CODES? If an error occurs during operation, the machine displays an SC code ("SCnnn" , where "nnn" is a three-digit number). The machine stops and cannot be used when an SC code is displayed.
  • Page 55 Code Error Procedure SC306 Charge grid high voltage error: M Replace the magenta charge corona unit. SC307 Charge grid high voltage error: Y Replace the yellow charge corona unit. SC308 Charge cleaning unit: Position error: K Detach and reattach the black charge corona unit or replace it.

  • Page 56: Troubleshooting Image Quality Problems

    3. TROUBLESHOOTING IMAGE QUALITY PROBLEMS This section describes some common image quality problems and tells you what to do about them. Paper Feed Direction Before you begin this section, note that the dark arrow in each illustration indicates the direction of paper feed. 3.1 IMAGE QUALITY PROBLEMS 3.1.1 PROBLEM 1: WHITE SPOTS White dots or small lines appear, spaced at 314 mm (12 in.)

  • Page 58: Problem 2: Sharp Spots

    3.1.2 PROBLEM 2: SHARP SPOTS These spots mark the page with very sharp dots at 314 mm (12 in.) intervals in the direction of paper feed. CAUSE: The drum unit has worn out or the drum is scratched. NOTE: See the following page for an actual sample. The sample image is not at 1:1 scale.

  • Page 60: Problem 3: Vertical Stripes

    3.1.3 PROBLEM 3: VERTICAL STRIPES Vertical stripes (less than 1 mm wide) appear, parallel to the direction of paper feed. CAUSE: 1. The drum unit has worn out or the drum is scratched. 2. The blade of the drum cleaning unit has worn out and cannot clean properly.

  • Page 62: Problem 4: Density Too Low

    3.1.4 PROBLEM 4: DENSITY TOO LOW Sheets are too light, especially in areas of solid fill. CAUSE: The density setting is too low. NOTE: See the following page for an actual sample. The sample image is not at 1:1 scale. Step 1 In [Adjustment] menu, carry out 3-820-002 (Execute Density Adj).

  • Page 64: Problem 5: Density Too High

    3.1.5 PROBLEM 5: DENSITY TOO HIGH Sheets are too dark, especially in areas of solid fill. CAUSE: The density setting is too high, or the developer has deteriorated. NOTE: See the following page for an actual sample. The sample image is not at 1:1 scale. Step 1 In [Adjustment] menu, carry out 3-820-002 (Execute Density Adj).

  • Page 66: Problem 6: Dirty Background

    3.1.6 PROBLEM 6: DIRTY BACKGROUND Random "powdered" dots appear, creating a dirty background. CAUSE: The developer has deteriorated. NOTE: See the following page for an actual sample. The sample image is not at 1:1 scale. Step 1 Replace the developer. Step 2 If changing the developer does not solve the problem, call for service.

  • Page 68: Problem 7: Patchy

    3.1.7 PROBLEM 7: PATCHY Printed sheets are patchy. CAUSE: The developer has deteriorated. NOTE: See the following page for an actual sample. The sample image is not at 1:1 scale. Step 1 Print three full-page A3 or DLT sheets in each color (cyan, yellow, magenta, and black).

  • Page 70: Problem 8: Streaks (1)

    3.1.8 PROBLEM 8: STREAKS (1) Wide streaks appear in the direction of paper feed. CAUSE: The electrical discharge from the charge corona unit is not constant. NOTE: See the following page for an actual sample. The sample image is not at 1:1 scale. Step 1 In [Adjustment] menu, carry out SP 3-820-002 (Execute Density Adj).

  • Page 72: Problem 9: Streaks (2)

    3.1.9 PROBLEM 9: STREAKS (2) When printing on one side only, toner streaks appear only on the printed side or only on the back. Toner streaks appear even when printing only in cyan, magenta, yellow, or black. CAUSE: 1. The image transfer belt cleaning unit is faulty. 2.

  • Page 73: Problem 10: White Lines Or Drag Marks

    3.1.10 PROBLEM 10: WHITE LINES OR DRAG MARKS White strips (about 314 mm, 12.4 inches wide) or drag marks appear on prints, or if fine white lines appear on the front of prints. CAUSE: There is dirt or oil on the surface of the drum unit.
  • Page 74 White lines...
  • Page 75 Drag marks...

  • Page 76: Problem 11: Toner Stains

    3.1.11 PROBLEM 11: TONER STAINS Toner stains appear on the prints. CAUSE: There is dirt or oil on the surface of the drum unit. Step 1 In [Adjustment] menu, enable 3-309-010 (Oil removal mode).

  • Page 77: Problem 12: Difference In Glossiness

    Load paper into the paper tray. You can use A3, SRA A3, DLT, or 12"x18" for test printing. Step 2 For users of Pro C900, press the Printer function/[fierydriven] key on the control panel. For Pro C900S, press the [Program] key. Step 3 Press [Print].

  • Page 78: Troubleshooting Paper Delivery Problems

    4. TROUBLESHOOTING PAPER DELIVERY PROBLEMS Important: For details about the items displayed in [Adjustment] menu, see the Adjustment Item Menu Guide. Problem Cause Solution Sheets cannot be The ends of the sheets are Remove the sheets from the paper tray, delivered.
  • Page 79 Problem Cause Solution Multiple sheets feed The ends of the sheets are Remove the sheets from the paper tray, in at once. slightly curled. flatten and fan them thoroughly, and then put them back into the paper tray. Sheets of differing paper types Removed mixed sheets from the paper or thickness are loaded in the tray, and then reload the paper tray with...
  • Page 80 4. Using the hex driver, turn the black screws to lock the front (1) and rear (2) locks. RPG068S RPG067S Carefully the registration unit drawer into the machine until it can go no further and locks into place. Rotate the lock lever (1) of the registration unit drawer clockwise. RPG043 Reconnect the ground leakage circuit breaker for the machine and fixing heater.
  • Page 81 Press the [Reset PM Counter:Paper Transfer Roller Unit] button. If a confirmation message appears, press the [Continue] button. Note: The counter will be reset. When the counter is reset, press the [Confirm] button. Copyright © 2008, 2009 G178-9504B...
  • Page 82 Introduction This manual contains detailed instructions and notes on the operation and use of this machine. For your safety and benefit, read this manual carefully before using the machine. Keep this manual in a handy place for quick reference. Important •...
  • Page 83 TABLE OF CONTENTS IMPORTANT NOTICE ..................... 4 1. Opening the [Adjustment] Menu ...........5 2. Display/Items and Features ............6 3. Values for Settings on the [Adjustment] Menu ......8 3.1 [Adjustment] List......................8 3.2 Adjustment Settings ....................11 4. Using the [Adjustment Settings for Skilled Operators] Menu ..28 4.1 Preparation: Displaying the [Adjustment Settings for Skilled Operators] menu ..

  • Page 84: Important Notice

    IMPORTANT NOTICE IMPORTANT NOTICE SAFETY INFORMATION RWARNING 1. Do not open or remove the exterior covers while the main switch is turned on. 2. To avoid injury, never touch moving or high voltage components. 3. Keep hands away from internal components. Mechanisms inside the machine can activate automatically, causing injury to hands.

  • Page 85: Opening The [Adjustment] Menu

    Turn the main power switch to ON, and wait for the machine to warm up. After the machine has warmed up, press the Printer function/[fierydriven] key on the control panel for users of Pro C900. For users of Pro C900S, press the [Program] key to display the Main Menu.

  • Page 86: Display/Items And Features

    2. Display/Items and Features 2. Display/Items and Features SUP013S 1. Items of Settings Adjustment Settings are displayed in order. SUP008S 2. [Open All], [Close All] Open or close all Adjustment Settings categories at the same time. 3. Sorting Types of Adjustment Settings can be scrolled or searched through by [Page] or [Line].
  • Page 87 2. Display/Items and Features 2.1.1 Inputting To enter numbers or select items, use the machine’s [./*], [1-0], and [#] keys.

  • Page 88: Values For Settings On The [Adjustment] Menu

    3. Values for Settings on the [Adjustment] Menu 3. Values for Settings on the [Adjustment] Menu 3.1 [Adjustment] List Note: Items are displayed according to the direction of paper feed, which you can specify by pressing [Moving Direction = Horizontal (right and left)] and [Crossing Direction = Vertical (top and bottom)].
  • Page 89 3. Values for Settings on the [Adjustment] Menu u Finishing Position Adjustments Item Description Reference 6-700 Staple Pos. Adj. Adjust the vertical position of the 3.2.2 staples. 6-705 Punch Pos. Adj. (V) Adjust the horizontal position of the punch holes. Specify this setting for all types of punches.
  • Page 90 3. Values for Settings on the [Adjustment] Menu u Other Adjustment Settings Item Description Reference 1-730 Detect Skew Use this if the print image is misaligned 3.2.4 by more than 2-3 mm when printing on 1-761 Detect Side Regist color, pre-printed, or narrow sheets up to 147 mm wide.

  • Page 91: Adjustment Settings

    3. Values for Settings on the [Adjustment] Menu 3.2 Adjustment Settings 3.2.1 Shift Image Adjustment 1. Using the [./*] key and [1-0] keys, enter the value you require for the setting, and then press the [#] key. Note: 1. Leading Edge Registration1,2 + shifts right.
  • Page 92 A4/LT LCT Upper Tray A4/LT LCT Middle Tray A4/LT LCT Lower Tray Main Bypass Tray A3/DLT LCT1 Upper Tray A3/DLT LCT1 Lower Tray A3/DLT LCT2 Upper Tray A3/DLT LCT2 Lower Tray Note: Settings for A4/LT LCT are available only on Pro C900.
  • Page 93 3. Values for Settings on the [Adjustment] Menu 3.2.2 Finishing Position Adjustments 1. Using the [./*] key and [1-0] keys, enter the value you require for the setting, and then press the [#] key. Item Setting Default Maxim Minim Gradat Unit Value Value...
  • Page 94 3. Values for Settings on the [Adjustment] Menu Item Setting Default Maxim Minim Gradat Unit Value Value Value Value Vertical DLT Vertical LG Vertical LT Vertical Other 6-735 Fold Pos. Adj. A3 Vertical B4 Vertical A4 Vertical B5 Vertical 12"X18" Vertical DLT Vertical LG Vertical...
  • Page 95 3. Values for Settings on the [Adjustment] Menu Note: Enter the degree of edge square deviation in "Rect. Angle Adj.".
  • Page 96 3. Values for Settings on the [Adjustment] Menu 3.2.3 Jogger Adjustments 1. Using the [./*] key and [1-0] keys, enter the value you require for the setting, and then press the [#] key. Item Setting Default Maxim Minim Gradat Unit Value Value Value...
  • Page 97 3. Values for Settings on the [Adjustment] Menu Item Setting Default Maxim Minim Gradat Unit Value Value Value Value LG Vertical LT Vertical Horizontal HLT Vertical Horizontal Other 6-720 End Bind Jogger Adj Horizontal Horizontal Horizontal 6-740 Adj. Booklet Stapling Pos. A3 Vertical +1.5 -1.5...

  • Page 98: Detect Skew

    A4/LT LCT Upper Tray A4/LT LCT Middle Tray A4/LT LCT Lower Tray Main Bypass Tray A3/DLT LCT1 Upper Tray A3/DLT LCT1 Lower Tray A3/DLT LCT2 Upper Tray A3/DLT LCT2 Lower Tray Note: Settings for A4/LT LCT are available only on Pro C900.

  • Page 99: Detect Side Regist

    A4/LT LCT Upper Tray A4/LT LCT Middle Tray A4/LT LCT Lower Tray Main Bypass Tray A3/DLT LCT1 Upper Tray A3/DLT LCT1 Lower Tray A3/DLT LCT2 Upper Tray A3/DLT LCT2 Lower Tray Note: Settings for A4/LT LCT are available only on Pro C900.

  • Page 100: Paper Curl Adjustment

    3. Values for Settings on the [Adjustment] Menu 1 Paper Curl Adjustment 1. Using the [./*] key and [1-0] keys, enter the value you require for the setting, and then press the [#] key. Item Setting Selection Default value 1-906 Paper Curl Paper 0: Default Position: Lower...

  • Page 101: Erase Paper Lead Edge

    3. Values for Settings on the [Adjustment] Menu 1 Erase Paper Lead Edge 1. Using the [./*] key and [1-0] keys, enter the value you require for the setting, and then press the [#] key. Item Setting Default Maxim Minim Gradat Unit Value...
  • Page 102 3. Values for Settings on the [Adjustment] Menu Item Setting Default Maxim Minim Gradat Unit Value Value Value Value Trace: Special5 Plain: Special5 MidThick: Special5 Trace: Special6 Plain: Special6 MidThick: Special6...

  • Page 103: Detect Multi Feed

    A4/LT LCT Upper Tray A4/LT LCT Middle Tray A4/LT LCT Lower Tray Main Bypass Tray A3/DLT LCT1 Upper Tray A3/DLT LCT1 Lower Tray A3/DLT LCT2 Upper Tray A3/DLT LCT2 Lower Tray Note: Settings for A4/LT LCT are available only on Pro C900.

  • Page 104: Blow Fan Duty Adj

    3. Values for Settings on the [Adjustment] Menu 1 Blow Fan Duty Adj. 1. Using the [./*] key and [1-0] keys, enter the value you require for the setting, and then press the [#] key. Item Setting Default Maxim Minim Gradat Unit Value...

  • Page 105: Air Feed Start Time Adj

    3. Values for Settings on the [Adjustment] Menu 1 Air Feed Start Time Adj. 1. Using the [./*] key and [1-0] keys, enter the value you require for the setting, and then press the [#] key. Item Setting Default Maxim Minim Gradat Unit...

  • Page 106: Initialize T Sensor

    3. Values for Settings on the [Adjustment] Menu 1 Initialize T Sensor Press the color to initialize the sensor, and then press the [#] key. If you press [Execute], the machine carries out initialization every time the developer is replaced. Item Setting Selection...

  • Page 107: Stacker Full Setting

    3. Values for Settings on the [Adjustment] Menu 1 Stacker Full Setting 1. Using the [./*] key and [1-0] keys, enter the value you require for the setting, and then press the [#] key. Item Setting Selection Default Value 6-770 Stacker Full Setting 0: 100% 0: 100%...

  • Page 108: Using The [Adjustment Settings For Skilled Operators] Menu

    4. Using the [Adjustment Settings for Skilled Operators] Menu 4. Using the [Adjustment Settings for Skilled Operators] Menu You can specify some of the items that are available on the [Adjustment] menu on the [Adjustment Settings for Skilled Operators] menu also. 4.1 Preparation: Displaying the [Adjustment Settings for Skilled Operators] menu To use the [Adjustment Settings for Skilled Operators] menu, you must first...
  • Page 109 4. Using the [Adjustment Settings for Skilled Operators] Menu 4. Press [Administrator Authentication Management]. If any keys cannot be selected on the display, press [ Next]. 5. Press [Machine Management]. 6. Select [On] for "Admin. Authentication". 7. Press [OK].
  • Page 110 4. Using the [Adjustment Settings for Skilled Operators] Menu 8. Press [Exit]. [Adjustment Settings for Skilled Operators] appears.

  • Page 111: Change The [Adjustment Settings For Skilled Operators] Mode

    4. Using the [Adjustment Settings for Skilled Operators] Menu 4.2 Change the [Adjustment Settings for Skilled Operators] Mode Press [Adjustment Settings for Skilled Operators]. Press [Login]. 3. Enter your login user name, and then press [OK]. If you are logging on as the administrator for the first time, enter "admin". 4.
  • Page 112 4. Using the [Adjustment Settings for Skilled Operators] Menu 5. Enter your login password again, and then press [OK]. The screen appears for Adjustment Settings for Skilled Operators Mode. Note: If a print job is suspended, press [APL Window] instead of [Exit] to exit the Adjustment Settings for Skilled Operators Mode.

  • Page 113: Values For Settings On The [Adjustment Settings For Skilled Operators] Menu

    4. Using the [Adjustment Settings for Skilled Operators] Menu 4.3 Values for Settings on the [Adjustment Settings for Skilled Operators] Menu For details about each setting in this menu, see the corresponding SP number in "3. Values for Settings in the [Adjustment] Menu". Although setting names might differ, matching numbers indicate the same function.
  • Page 114 Index Items of Settings, 6 Adj Leading edge stopper press, 9, 16 Adj. Booklet Stapling Pos., 9, 17 Jogger Adjustments, 9, 16 Adjust Output jog Position, 9, 16 Air Feed Start Time Adj., 10, 25 Leading Edge Registration1, 8, 11, 12, 18, 19, 23 Leading Edge Registration2, 8, 11, 12, 18, 19, 23 Blow Fan Duty Adj., 10, 24 Oil removal mode, 10, 25...
  • Page 115 Copyright © 2008, 2009 G178-9505B...

This manual is also suitable for:

Pro c900s

Table of Contents