Page 1 Ryan Masterfile.book Page i Monday, June 9, 2003 2:33 PM Startup and Reference Guide HP Notebook Series Document Part Number: 335555-001 August 2003 Part 1: Startup The Startup part of this guide explains how to set up your notebook for the first time.
Page 2: Table Of Contents
Ryan Masterfile.book Page ii Monday, June 9, 2003 2:33 PM Contents 1 Startup 2 System Components 3 Keyboard 4 Power 5 Drives 6 Multimedia 7 Communications 8 Hardware Options and Upgrades 9 Software Updates, Restorations and Utilities A Specifications Index...
Page 3 Ryan Masterfile.book Page 1 Monday, June 9, 2003 2:33 PM Part-1 Startup This Startup and Reference Guide provides information about setting up and using your notebook. To set up your notebook hardware and software for the first time, follow the procedures in “Part 1: Startup”. To learn more about using your notebook, refer to “Part 2: Reference.”...
Page 4: Setting Up The Hardware
Ryan Masterfile.book Page 2 Monday, June 9, 2003 2:33 PM Startup Setting Up the Hardware To set up the notebook for the first time, you need the notebook, the power cord 1, the AC adapter 2, and the battery pack 3. Insert the battery pack into the notebook, so that the battery can begin to charge as soon as the notebook is connected to external power.
Page 5: Inserting A Battery Pack
Ryan Masterfile.book Page 3 Monday, June 9, 2003 2:33 PM Startup Inserting a Battery Pack To insert the battery pack into the battery bay: 1. Turn the notebook upside down on a flat surface. 2. Insert the alignment tab on the battery pack into the alignment slot on the notebook.
Page 6: Opening The Notebook
Ryan Masterfile.book Page 4 Monday, June 9, 2003 2:33 PM Startup Opening the Notebook To open the notebook: 1. Place the notebook display-side up on a flat surface near an electrical outlet. 2. Slide the display release latch 1, then lift the display 2. Opening the notebook 1–4 Startup and Reference Guide—Part 1...
Page 7: Connecting The Notebook To External Power
Ryan Masterfile.book Page 5 Monday, June 9, 2003 2:33 PM Startup Connecting the Notebook to External Power To connect the notebook to external power: 1. Plug the AC adapter cable into the power connector 1. 2. Plug the power cord into the AC adapter 2, then into an electrical outlet 3.
Page 8: Charging A New Battery Pack
The battery charge light is on while the battery pack is charging. HP recommends that you leave the notebook connected to external power until the battery pack is fully charged and the battery charge light turns off.
Page 9: Turning On The Notebook
If you have installed a battery pack, make sure that the battery pack is firmly seated. Refer to the Worldwide Telephone Numbers booklet included with the notebook to contact an HP Customer Care Center. Startup and Reference Guide—Part 1 1–7...
Page 10: Setting Up The Software
Ryan Masterfile.book Page 8 Monday, June 9, 2003 2:33 PM Startup Setting Up the Software Ä CAUTION: To prevent file corruption and ensure that the correct drivers are installed, install software only when the notebook is connected to external power through the AC adapter. During the installation: Do not unplug the notebook from external power.
Page 11: Installing Optional Software
Ryan Masterfile.book Page 9 Monday, June 9, 2003 2:33 PM Startup Installing Optional Software Instructions for installing and using many of the applications and utilities included with the notebook are provided later in this guide. If you prefer to install optional software now, the following information may be helpful.
Page 12: Turning Off The Notebook
Ryan Masterfile.book Page 10 Monday, June 9, 2003 2:33 PM Startup Setting Regional and Display Preferences Keyboard language and other regional preferences, such as time, date, and currency format, are set in the Regional Options window of the operating system. To access the Regional Options window, select Start >...
Page 13 Ryan Masterfile.book Page 11 Monday, June 9, 2003 2:33 PM Startup Using the Notebook Safetly Protecting the Notebook Against Computer Viruses When you use the notebook for email, network, or Internet access, you expose the notebook to computer viruses. Computer viruses can disable the operating system, your applications, or your utilities or cause them to function abnormally.
Page 14: Protecting The Notebook From Power Surges
Ryan Masterfile.book Page 12 Monday, June 9, 2003 2:33 PM Startup Protecting the Notebook from Power Surges To protect the notebook from the power surges that may be caused by an unreliable power supply or an electrical storm: Plug the notebook power cord into an optional, high-quality surge protector available from most computer or electronic retailers.
Page 15: Getting Help
If you cannot solve a notebook problem by using this guide or the supplementary information, including the Troubleshooting guide, on the Documentation Library CD, you may need to contact HP. Using the Help and Support Center Installed on your notebook desktop is the Help and Support...
Page 16 Ryan Masterfile.book Page 14 Monday, June 9, 2003 2:33 PM Startup With the Help and Support Center, you can get immediate assistance before contacting an HP support specialist. For example, in Help and Support, you can: Troubleshoot and fix common notebook problems.
Page 17: Contacting Technical Support
Properties window, select the Support Information button. Refer to the Worldwide Telephone Numbers booklet included with the notebook to contact an HP Customer Care Center. To provide the fastest possible resolution of your problem, have the notebook and the following information available when...
Page 18 Ryan Masterfile.book Page 16 Monday, June 9, 2003 2:33 PM Startup 1–16 Startup and Reference Guide—Part 1...
Page 19 Ryan Masterfile.book Page 1 Monday, June 9, 2003 2:33 PM Part 2 Reference Startup and Reference Guide—Part 2...
Page 20 Ryan Masterfile.book Page 2 Monday, June 9, 2003 2:33 PM...
Page 21: System Components
Ryan Masterfile.book Page 1 Monday, June 9, 2003 2:33 PM System Components Contents Display ........2–2 Top .
Page 22: Display
Ryan Masterfile.book Page 2 Monday, June 9, 2003 2:33 PM System Components Display Display Display release latch Opens the notebook. 2–2 Startup and Reference Guide—Part 2...
Page 23: Top
Ryan Masterfile.book Page 3 Monday, June 9, 2003 2:33 PM System Components TouchPad Top: TouchPad TouchPad on/off button Enables/disables the TouchPad. TouchPad light On: TouchPad is enabled. TouchPad scroll zone* Scroll up or down. Left and right TouchPad Function like the left and right buttons buttons* on an external mouse.
Page 24: Keys
Ryan Masterfile.book Page 4 Monday, June 9, 2003 2:33 PM System Components Keys Top: Keys Function keys Perform system and application tasks. When combined with the fn key, the function keys f1and f3 through f12 perform additional tasks as hotkeys. Refer to the “Hotkey Quick Reference”...
Page 25: Power Controls
Ryan Masterfile.book Page 5 Monday, June 9, 2003 2:33 PM System Components Power Controls Top: Power Controls Power button* When the notebook is: Off, press to turn on the notebook. On, briefly press to initiate Hibernation. In Standby, briefly press to resume from Standby.
Page 26: Lights
Ryan Masterfile.book Page 6 Monday, June 9, 2003 2:33 PM System Components Lights Top: Lights Wireless On/Off light On: An integrated wireless device has been enabled. Caps lock light On: Caps lock is on. Num lock light On: Num lock or the keypad is on. 2–6 Startup and Reference Guide—Part 2...
Page 27: Audio Buttons
Ryan Masterfile.book Page 7 Monday, June 9, 2003 2:33 PM System Components Audio Buttons Top: Audio Buttons Decrease volume button Pressing the left side, decreases system volume. Mute button Mutes or restores volume. Increase volume button Pressing the right side, increases system volume.
Page 28: Front Panel
Ryan Masterfile.book Page 8 Monday, June 9, 2003 2:33 PM System Components Front Panel Front Panel Display release latch Opens the notebook. Stereo speakers (2) Produce stereo sound. Hard drive activity light On: The internal hard drive is being accessed. AC power light On: The notebook is receiving AC power.
Page 29: Rear Panel
Ryan Masterfile.book Page 9 Monday, June 9, 2003 2:33 PM System Components Rear Panel Connectors and Jacks Rear Panel: Connectors and Jacks Security cable slot Attaches an optional security cable to the notebook. RJ-11 telephone jack Connects a modem cable. (A modem cable is included with select models.) RJ-45 network jack Connects an Ethernet network cable.
Page 30: Vents
Ryan Masterfile.book Page 10 Monday, June 9, 2003 2:33 PM System Components Vents Rear Panel: Vents Exhaust vents Provides airflow to cool internal components. Ä To prevent overheating, do not obstruct vents. Do not allow a hard surface, such as a printer, or a soft surface, such as a pillow, blanket, rug, or thick clothing, to block airflow.
Page 31: Left Side
Left Side Connectors and Jacks Left Side: Connectors and Jacks Power connector Connects an AC adapter cable. Expansion port Connects to an optional HP Notebook Expansion Base. USB connector Connects an optional 1.1 or 2.0-compliant USB device. 1394 connector Connects an optional 1394 device, such as a camcorder.
Page 32: Vents
Ryan Masterfile.book Page 12 Monday, June 9, 2003 2:33 PM System Components Vents Left Side: Vents Exhaust vents Provide airflow to cool internal components. Ä To prevent overheating, do not obstruct vents. Do not allow a hard surface, such as a printer, or a soft surface, such as a pillow, blanket, rug, or thick clothing, to block airflow.
Page 33: Right Side
Ryan Masterfile.book Page 13 Monday, June 9, 2003 2:33 PM System Components Right Side Right Side Infrared port Provides wireless communication between the notebook and an optional IrDA-compliant device. Digital Media slot Supports SD, MMC, Memory Stick, and SmartMedia. Optical drive release button Opens the optical drive.
Page 34: Bottom
Ryan Masterfile.book Page 14 Monday, June 9, 2003 2:33 PM System Components Bottom Bays and Memory Compartment Bottom: Bays and Memory Compartment Battery pack release latch Releases a battery pack from the battery bay. Memory compartment Contains 2 memory slots. Depending on the model, when the notebook is shipped either one or both memory slots may be filled with a replaceable...
Page 35: Vents
Ryan Masterfile.book Page 15 Monday, June 9, 2003 2:33 PM System Components Vents Bottom: Vents Intake vents Provide airflow to cool internal components. Ä To prevent overheating, do not obstruct vents. Do not allow a hard surface, such as a printer, or a soft surface, such as a pillow, blanket, rug, or thick clothing, to block airflow.
Page 36: Labels
Ryan Masterfile.book Page 16 Monday, June 9, 2003 2:33 PM System Components Labels The labels affixed to the notebook and some notebook components provide information you may need when troubleshooting system problems or traveling internationally with the notebook. The Microsoft Certificate of Authenticity label contains the Product Key number.
Page 37: Additional Standard Components
Ryan Masterfile.book Page 17 Monday, June 9, 2003 2:33 PM System Components Additional Standard Components The components included with the notebook vary by region, country, notebook model, and the optional hardware ordered. The following sections identify the standard external accessories and components included with most notebook models.
Page 38: Adapters And Battery Pack
Ryan Masterfile.book Page 18 Monday, June 9, 2003 2:33 PM System Components Adapters and Battery Pack Additional Standard Components: Adapters and Battery Pack AC adapter Converts AC power to DC power. Country-specific modem Adapts the modem cable to a adapter (included by region non-RJ-11 telephone jack.
Page 39: Restoration And Documentation Cds
Ryan Masterfile.book Page 19 Monday, June 9, 2003 2:33 PM System Components Restoration and Documentation CDs CDs for repairing or reinstalling software and for obtaining supplementary information about the notebook are included with the notebook. For information about restoring, repairing, or reinstalling software, refer to “Software Updates, Restorations and Utilities.”...
Page 40 Ryan Masterfile.book Page 20 Monday, June 9, 2003 2:33 PM System Components 2–20 Startup and Reference Guide—Part 2...
Page 41: Keyboard
Ryan Masterfile.book Page 1 Monday, June 9, 2003 2:33 PM Keyboard Contents TouchPad ........3–2 Identifying TouchPad Components .
Page 42: Touchpad
Ryan Masterfile.book Page 2 Monday, June 9, 2003 2:33 PM Keyboard TouchPad Identifying TouchPad Components The TouchPad includes the following components: Identifying TouchPad components Button name Default assignment TouchPad on/off button Enables/disables the TouchPad. TouchPad light On: TouchPad is enabled. TouchPad scroll zone Scroll up or down.
Page 43: Using The Touchpad
Ryan Masterfile.book Page 3 Monday, June 9, 2003 2:33 PM Keyboard Using the TouchPad The TouchPad provides the navigation, selection, and scroll functions of an optional external mouse. To move the pointer, slide your finger across the TouchPad surface in the direction you want to move the pointer. If the pointer continues to move after you lift your finger from the TouchPad surface, wait a few seconds and the pointer will stop moving.
Page 44: Using Hotkey And Shortcut Keys
Ryan Masterfile.book Page 4 Monday, June 9, 2003 2:33 PM Keyboard Using Hotkey and Shortcut Keys Hotkey and shortcut keys are preset combinations of the with other keys on the keyboard. A hotkey is a combination of the key and one of the function keys.
Page 45: Power
Ryan Masterfile.book Page 5 Monday, June 9, 2003 2:33 PM Keyboard Hotkey and Shortcut Key Quick Reference The following table identifies the default hotkey and shortcut key functions. ✎ For information about changing the function of the hotkey, fn+f5 refer to the “Managing Power Options”...
Page 46: Hotkey And Shortcut Key Procedures
Ryan Masterfile.book Page 6 Monday, June 9, 2003 2:33 PM Keyboard Hotkey and Shortcut Key Procedures To use a hotkey or shortcut key command on the notebook keyboard, use either of the following procedures: Briefly press the key, then briefly press the second key of the hotkeys command.
Page 47 Composite video (televisions, camcorders, VCRs, and video capture boards with composite-video-in jacks) ✎ Composite video devices can only be connected to the notebook when it is docked in an optional HP Notebook Expansion Base. Startup and Reference Guide—Part 2 3–7...
Page 48 Ryan Masterfile.book Page 8 Monday, June 9, 2003 2:33 PM Keyboard Initiate Standby (fn+f5) hotkey is set by default to initiate Standby. Standby can fn+f5 be initiated only while the notebook is on. If the notebook is in Hibernation, you must restore from Hibernation before you can initiate Standby.
Page 49 Ryan Masterfile.book Page 9 Monday, June 9, 2003 2:33 PM Keyboard Play, Pause, or Resume an Audio CD or DVD (fn+f9) hotkey functions only when an audio CD or DVD is fn+f9 inserted. If the audio CD or DVD is: Not playing, press the hotkey to begin or resume fn+f9...
Page 50: Keypad
Ryan Masterfile.book Page 10 Monday, June 9, 2003 2:33 PM Keyboard Keypad The keypad consists of 17 keys that can be used like the keys on an external keypad. Identifying the keypad keys 3–10 Startup and Reference Guide—Part 2...
Page 51: Quick Launch Buttons
Ryan Masterfile.book Page 11 Monday, June 9, 2003 2:33 PM Keyboard Quick Launch Buttons The three Quick Launch buttons enable you to use one keystroke to access a software application or to activate a wireless network device. Identifying the Quick Launch buttons Button name Default assignment Media button...
Page 52: Drives
Ryan Masterfile.book Page 12 Monday, June 9, 2003 2:33 PM Keyboard Using Custom Assignments and Schemes A Quick Launch button can be re-assigned to an Internet or network destination or to any software application or data file. For example, an Quick Launch button can be assigned to open your Internet browser to a favorite Web page or to open an application, such as Microsoft Word, or a document, such as an Excel worksheet, on a notebook or network drive.
Page 53 Ryan Masterfile.book Page 1 Monday, June 9, 2003 2:33 PM Power Contents Selecting a Power Source......4–2 Understanding Standby, Hibernation and Shutdown .
Page 54: Selecting A Power Source
Charged battery pack in the applications. notebook External power supplied through the following devices: ❐ AC adapter ❐ Optional HP Notebook Expansion Base Charge or calibrate a battery External power supplied through: pack in the notebook. AC adapter Optional HP Notebook Expansion Base...
Page 55: Understanding Standby, Hibernation And Shutdown
Ryan Masterfile.book Page 3 Monday, June 9, 2003 2:33 PM Power Understanding Standby, Hibernation and Shutdown This section describes Standby, Hibernation, and shutdown and explains when to implement them. Standby and Hibernation are energy-saving features that can be initiated by you or by the system.
Page 56: Hibernation
Ryan Masterfile.book Page 4 Monday, June 9, 2003 2:33 PM Power Hibernation Hibernation takes a snapshot of the current system memory, saves it to the hard drive, then shuts down the notebook. When you resume from Hibernation, your work returns to the screen exactly as you left it.
Page 57: Shutdown
Ryan Masterfile.book Page 5 Monday, June 9, 2003 2:33 PM Power To verify that Hibernation is enabled, select Start > Control Panel > Performance and Maintenance > Power Options > Hibernate tab. Be sure that the Enable Hibernation check box is selected.
Page 58: Initiating Standby, Hibernation Or Shutdown
Ryan Masterfile.book Page 6 Monday, June 9, 2003 2:33 PM Power Initiating Standby, Hibernation or Shutdown The following sections describe when to initiate Standby or Hibernation and when to shut down your notebook. When Leaving Your Work Initiate Standby for shorter times and Hibernation for longer times or for more power conservation.
Page 59: When Using Infrared Or Drive Media
Ryan Masterfile.book Page 7 Monday, June 9, 2003 2:33 PM Power When Using Infrared or Drive Media Standby and Hibernation interfere with the use of infrared communication and drive media. If the notebook is in Standby or Hibernation, you cannot initiate an infrared transmission.
Page 60: Using Default Power Settings
Ryan Masterfile.book Page 8 Monday, June 9, 2003 2:33 PM Power Using Default Power Settings This section explains the default Standby, Hibernation, and shutdown procedures and includes information about turning the display on or off. You can change many of these settings according to your preferences.
Page 61: Turning The Notebook Or Display On Or Off
Ryan Masterfile.book Page 9 Monday, June 9, 2003 2:33 PM Power Turning the Notebook or Display On or Off Task Procedure Results Turn on the Press the power button. The power/standby light notebook. turns on. ✎ Pressing the The operating system power button loads.
Page 62: Using Emergency Shutdown Procedures
Ryan Masterfile.book Page 10 Monday, June 9, 2003 2:33 PM Power Using Emergency Shutdown Procedures If the notebook does not respond and you are unable to use normal Windows shutdown procedure, try the following emergency shutdown procedures in the sequence provided: Press Select the Shut Down button, then select ctrl+alt+delete.
Page 63: Initiating Or Resuming From Standby
Ryan Masterfile.book Page 11 Monday, June 9, 2003 2:33 PM Power Initiating or Resuming from Standby Task Procedure Result Initiate Standby With the notebook on, use The power/standby light either of the following flashes. procedures: The screen clears. Press the fn+f5 hotkey. Select Start >...
Page 64: Initiating Or Resuming From Hibernation
Ryan Masterfile.book Page 12 Monday, June 9, 2003 2:33 PM Power Initiating or Resuming from Hibernation Task Procedure Result Initiate With the notebook on, use either The power/standby Hibernation of the following procedures: light turns off. Briefly press the power The screen clears.
Page 65: Managing Power Options
Ryan Masterfile.book Page 13 Monday, June 9, 2003 2:33 PM Power Managing Power Options Many of the default power settings, such as timeouts and alarms, can be changed in Power Options. For example, you can set an audio alert to warn you when the battery reaches a low-power condition.
Page 66: Displaying The Power Meter Icon
Ryan Masterfile.book Page 14 Monday, June 9, 2003 2:33 PM Power Displaying the Power Meter Icon The Power Meter icon changes shape to indicate whether the notebook is running on a battery pack or external power. Double-click the icon to display the Power Options window. To hide or show the Power Meter icon on the taskbar: 1.
Page 67: Using A Security Password
Ryan Masterfile.book Page 15 Monday, June 9, 2003 2:33 PM Power Using a Security Password You can add a security feature that prompts you for a password when the notebook turns on or resumes from Standby or Hibernation. To set a password prompt, access the Power Options window > Advanced tab.
Page 68: Using Battery Power
Ryan Masterfile.book Page 16 Monday, June 9, 2003 2:33 PM Power Using Battery Power Identifying the Power Lights Battery pack procedures refer to the front panel lights: Identifying the battery and power/standby lights Top: TouchPad Power/standby light On when the notebook has power. Battery light On in the absence of AC power, when the notebook is running on battery...
Page 69: Switching Between Battery And External Power
Ryan Masterfile.book Page 17 Monday, June 9, 2003 2:33 PM Power Switching Between Battery and External Power The notebook switches between AC power and battery power according to the availability of an external AC power source, always preferring AC power. If the notebook contains a charged battery pack and is running on external AC power, the notebook will switch to battery power only if the AC adapter is disconnected from the notebook.
Page 70: Monitoring The Charge In A Battery Pack
Ryan Masterfile.book Page 18 Monday, June 9, 2003 2:33 PM Power Monitoring the Charge in a Battery Pack Obtaining Accurate Charge Information To increase the accuracy of all battery charge displays: Allow the battery pack to fully discharge before charging it. Charge the battery pack fully.
Page 71: Managing Low-Battery Conditions
Ryan Masterfile.book Page 19 Monday, June 9, 2003 2:33 PM Power Managing Low-Battery Conditions Some low-battery condition alerts and system responses can be changed in the Power Options window of the operating system. The information in this section describes the alerts and system responses set at the factory.
Page 72: When External Power Is Available
Ryan Masterfile.book Page 20 Monday, June 9, 2003 2:33 PM Power Resolving Low-Battery Conditions Ä CAUTION: If the notebook has reached a critical low-battery condition and has begun to initiate Hibernation, do not restore power until the Power/Standby light turns off. When External Power Is Available To resolve a low-battery condition when external power is available, connect the AC adapter.
Page 73: Calibrating A Battery Pack
Ryan Masterfile.book Page 21 Monday, June 9, 2003 2:33 PM Power Calibrating a Battery Pack When to Calibrate Even if a battery pack is heavily used, it should not be necessary to calibrate it more than once a month. It is not necessary to calibrate a new battery pack before first use.
Page 74 Ryan Masterfile.book Page 22 Monday, June 9, 2003 2:33 PM Power Ä CAUTION: If you plan to leave the notebook unattended during discharge, save your work before starting the discharge procedure. To fully discharge the battery pack: 1. Select the power icon on the taskbar or select Start > Control Panel >...
Page 75: Recharging The Battery Pack
Ryan Masterfile.book Page 23 Monday, June 9, 2003 2:33 PM Power Recharging the Battery Pack 1. Connect the notebook to external power and keep the notebook connected until the battery pack is fully recharged and the battery light turns off. You can use the notebook while the battery pack is recharging, but the battery pack will charge faster if the notebook is turned off.
Page 76: Storing A Battery Pack
Ryan Masterfile.book Page 24 Monday, June 9, 2003 2:33 PM Power Storing a Battery Pack If the notebook will be unused and unplugged for more than 2 weeks, remove and store the battery pack. Ä CAUTION: To prevent damage to a battery pack, do not expose it to high temperatures for extended periods of time.
Page 77: Battery Conservation Settings
Ryan Masterfile.book Page 25 Monday, June 9, 2003 2:33 PM Power Battery Conservation Settings Using the following battery conservation settings and procedures extends the run time of a battery pack. Turn off wireless and local area network (LAN) connections and exit modem applications when you are not using them. Disconnect from the notebook any external devices that use power from the notebook.
Page 78: Replacing A Battery Pack
Ryan Masterfile.book Page 26 Monday, June 9, 2003 2:33 PM Power Replacing a Battery Pack Ä CAUTION: To prevent loss of work when removing a battery pack that is the only power source, initiate Hibernation or turn off the notebook before removing the battery pack.
Page 79: Disposing Of A Used Battery Pack
Ryan Masterfile.book Page 27 Monday, June 9, 2003 2:33 PM Power ❏ To insert a battery pack, insert the alignment tab on the battery pack into the alignment slot on the notebook, then tilt the battery pack downward until it snaps into place. Inserting a battery pack 2.
Page 80 Ryan Masterfile.book Page 28 Monday, June 9, 2003 2:33 PM Power 4–28 Startup and Reference Guide—Part 2...
Page 81 Ryan Masterfile.book Page 1 Monday, June 9, 2003 2:33 PM Drives Contents Understanding Drives......5–2 Adding a Drive to the System .
Page 82: Multimedia
Ryan Masterfile.book Page 2 Monday, June 9, 2003 2:33 PM Drives Understanding Drives The hard drive and optical (CD/DVD) drive are standard features of the notebook, but the optical drive features vary by model. Some notebooks include a diskette drive and/or a USB Digital drive.
Page 83: Caring For Drives
Ryan Masterfile.book Page 3 Monday, June 9, 2003 2:33 PM Drives Caring for Drives Drives are fragile notebook components that must be handled with care. The following cautions apply to all drives. Additional cautions are included with the procedures to which they apply. Ä...
Page 84: Hard Drive
Ryan Masterfile.book Page 4 Monday, June 9, 2003 2:33 PM Drives Hard Drive This section discusses the primary hard drive of the notebook. Identifying the Hard Drive Activity Light The hard drive activity light turns on when the internal hard drive is being accessed.
Page 85: Replacing The Internal Hard Drive
Ryan Masterfile.book Page 5 Monday, June 9, 2003 2:33 PM Drives Replacing the Internal Hard Drive The hard drive in the hard drive bay is the internal hard drive. Remove the internal hard drive only for repair or replacement. Ä CAUTION: To prevent an unresponsive system and loss of work, do not begin this procedure until you have: Saved your work, closed all open applications, and shut down the...
Page 86 Ryan Masterfile.book Page 6 Monday, June 9, 2003 2:33 PM Drives 7. Remove the hard drive cover 1. 8. Using the handle, unseat the hard drive by sliding the hard drive towards the edge of the notebook 2, then remove it from the hard drive bay 3.
Page 87 Ryan Masterfile.book Page 7 Monday, June 9, 2003 2:33 PM Drives 9. To install a hard drive, lower the hard drive into the hard drive bay 1, then slide the hard drive away from the notebook edge until it is fully seated 2. Lower the hard drive cover onto the hard drive bay 3.
Page 88: Optical Drive
Ryan Masterfile.book Page 8 Monday, June 9, 2003 2:33 PM Drives 10. If you have installed a hard drive, reinsert the 4 hard drive retaining screws. (If you removed but did not replace a hard drive, put the retaining screws in a safe place.) Replacing the hard drive retaining screws Optical Drive Ä...
Page 89: Inserting An Optical Disc
Ryan Masterfile.book Page 9 Monday, June 9, 2003 2:33 PM Drives Inserting an Optical Disc 1. Turn on the notebook. 2. Press the release button 1 on the drive bezel to release the media tray, then pull the tray outward until it is fully extended 2.
Page 90: Removing An Optical Disc (With Power)
Ryan Masterfile.book Page 10 Monday, June 9, 2003 2:33 PM Drives Removing an Optical Disc (With Power) 1. Turn on the notebook. 2. Press the release button 1 on the drive bezel to release the media tray, then pull the tray outward until it is fully extended 2.
Page 91: Removing An Optical Disc (Without Power)
Ryan Masterfile.book Page 11 Monday, June 9, 2003 2:33 PM Drives Removing an Optical Disc (Without Power) If the notebook is turned off or if no power is available, the release button on the optical drive will not work. To remove a disc from an optical drive without using the release button: 1.
Page 92: Playing An Optical Disc
Ryan Masterfile.book Page 12 Monday, June 9, 2003 2:33 PM Drives Playing an Optical Disc You can play a CD in a CD drive or a DVD drive. You can play a DVD only in a DVD drive. The information in this section applies to most optical drives and most disc software.
Page 93: Protecting Playback
Ryan Masterfile.book Page 13 Monday, June 9, 2003 2:33 PM Drives Protecting Playback Ä CAUTION: Inserting or removing any device while running any multimedia application may pause or stop the play. Ä CAUTION: Initiating Standby or Hibernation while playing a drive medium may stop the play or diminish the quality of the play.
Page 94: Setting The Boot Order
Ryan Masterfile.book Page 14 Monday, June 9, 2003 2:33 PM Drives Setting the Boot Order By default, the notebook starts up from the internal hard drive. You can set the notebook to start up from any bootable CD or DVD in the optical drive. A bootable CD or DVD contains files needed by the notebook to start up and operate properly.
Page 95 Ryan Masterfile.book Page 1 Monday, June 9, 2003 2:33 PM Multimedia Contents Adjusting Volume ......6–3 Using the Volume Buttons .
Page 96 Ryan Masterfile.book Page 2 Monday, June 9, 2003 2:33 PM Multimedia Preparing to Use Easy CD & DVD Creator ..6–15 Formatting Recording Media....6–16 Creating CDs .
Page 97: Adjusting Volume
Ryan Masterfile.book Page 3 Monday, June 9, 2003 2:33 PM Multimedia Adjusting Volume Volume can be adjusted by using the audio buttons on the notebook or by using the volume control software. The mute button overrides all software volume settings. Using the Volume Buttons To adjust volume using the audio buttons: To increase volume, press the increase volume button 3.
Page 98: Using The Volume Control
Ryan Masterfile.book Page 4 Monday, June 9, 2003 2:33 PM Multimedia Using the Volume Control To place the volume control icon on the taskbar: Select Start > Control Panel > Sounds, Speech, and Audio Devices > Sounds and Audio Devices icon > Volume tab. Select the Place volume icon in the task bar check box.
Page 99: Using The Speakers
Ryan Masterfile.book Page 5 Monday, June 9, 2003 2:33 PM Multimedia Using the Speakers The internal speakers plays sound in stereo from applications, the operating system, games, drive media, the Internet, and other sources. ✎ If an external device, such as a headset, is connected to the audio-out jack, the internal speakers are disabled.
Page 100: Identifying The Audio Jacks
Ryan Masterfile.book Page 6 Monday, June 9, 2003 2:33 PM Multimedia Identifying the Audio Jacks The notebook has 2 audio jacks: The microphone jack 1, sometimes called the line-in jack, connects an optional monaural or stereo microphone. The audio line-out jack 2, sometimes called a line-out jack, connects headphones or external stereo speakers.
Page 101: Using The Microphone Jack
Ryan Masterfile.book Page 7 Monday, June 9, 2003 2:33 PM Multimedia Using the Microphone Jack When connecting a microphone to the microphone jack, use a monaural microphone with a 3.5-mm plug. A monaural electret condenser microphone is recommended. If you connect a stereo microphone, left channel sound will record on both channels.
Page 102: Connecting An S-Video Device
Ryan Masterfile.book Page 8 Monday, June 9, 2003 2:33 PM Multimedia Connecting an S-Video Device Connecting the Audio The S-Video jack supports video signals only. If you are setting up a configuration that combines audio and video functions, such as playing a DVD movie on your notebook and displaying it on your television, you will need a standard 3.5-mm audio cable available from most computer or electronics retailers.
Page 103: Turning A Video Device On And Off
Ryan Masterfile.book Page 9 Monday, June 9, 2003 2:33 PM Multimedia Turning a Video Device On and Off When an S-Video device is turned on, an image is displayed. When the device is off, an image is not displayed. To turn on a video device that is connected to the notebook: Start or restart the notebook.
Page 104: Using Multimedia Software
Ryan Masterfile.book Page 10 Monday, June 9, 2003 2:33 PM Multimedia Region-specific formats are set at the factory for most notebooks, but the region setting can be changed on any notebook. Refer to “Changing DVD Region Settings” later in this chaper. Color television format settings are changed in the Setup utility.
Page 105: Playing Video Cds And Dvds With Intervideo Windvd
PCFriendly that may interfere with WinDVD. Installing WinDVD If WinDVD has been uninstalled and you insert a DVD that contains a non-HP player program, you are prompted to install that non-HP player program. If you prefer to use WinDVD, decline the non-HP player installation, close the installation window, and re-install WinDVD.
Page 106: Changing Dvd Region Settings
Ryan Masterfile.book Page 12 Monday, June 9, 2003 2:33 PM Multimedia To play a DVD or video CD: 1. Insert the DVD or video CD into the optical drive. 2. Assign WinDVD to play the video: ❏ If the Microsoft Windows XP AppPicker window is displayed, select Play Video By Using WinDVD.
Page 107: Creating Cds With Roxio Easy Cd & Dvd Creator
Ryan Masterfile.book Page 13 Monday, June 9, 2003 2:33 PM Multimedia To change the region setting on drive media: 1. Open WinDVD by doing one of the following: ❏ Select the WinDVD icon on the taskbar. ❏ Select Start > All Programs > InterVideo WinDVD > InterVideo WinDVD.
Page 108 Ryan Masterfile.book Page 14 Monday, June 9, 2003 2:33 PM Multimedia Understanding Easy CD & DVD Creator Features Easy CD & DVD Creator includes the following 4 applications: Application Allows you to Disc Copier create backup copies of personal discs. Creator Classic create CDs backups or archives of files on your hard drive.
Page 109: Preparing To Use Easy Cd & Dvd Creator
CD. The write process is sensitive to vibration. Choosing Recording Media HP recommends using high-quality media that correspond to the maximum speed of the optical drive. The notebook can write or copy to CDs which provide one-time, non-erasable recording (CD-R) or to CDs which provide erasable recording (CD-RW).
Page 110: Formatting Recording Media
Ryan Masterfile.book Page 16 Monday, June 9, 2003 2:33 PM Multimedia Responding to the UDF Prompt The first time you insert a CD into an optical drive, you may be prompted to install Universal Disk Format (UDF) Reader. The UDF Reader is preinstalled on select notebook models. If UDF Reader is installed on your notebook, a CD created with the Drag-to-Disc application can be used in a compatible optical drive on a computer without Drag-to-Disc, provided you select...
Page 111: Creating Cds
Ryan Masterfile.book Page 17 Monday, June 9, 2003 2:33 PM Multimedia To record information to a CD using Creator Classic or Disc Copier, do not use a CD formatted for Drag-to-Disc or erase the information from a rewriteable disc to use it again. Creating CDs Refer to the Roxio Easy CD and DVD Creator online User’s Guide for details on burning CDs.
Page 112: Selecting Easy Cd & Dvd Creator Settings
Ryan Masterfile.book Page 18 Monday, June 9, 2003 2:33 PM Multimedia Erasing Recorded Media with Creator Classic To erase recorded media formatted with Creator Classic: 1. Insert the CD into the optical drive. 2. Open the Creator Classic window by selecting Start > All Programs >...
Page 113: Creating Dvds Using Intervideo
Ryan Masterfile.book Page 19 Monday, June 9, 2003 2:33 PM Multimedia The following table describes the Track-at-Once and Disc-at-Once recording methods. Option Description Track-at-Once Writes data to the disc in multiple passes and allows you to copy one track or data file at a time to the disc.
Page 114: Preparing To Use Intervideo Windvd Creator
DVD. The write process is sensitive to vibration. Choosing Recording Media HP recommends using high-quality media that correspond to the maximum speed of the optical drive. The notebook can write or copy to DVDs which provide one-time, non-erasable recording (DVD+R) or to DVDs which provide erasable recording (DVD+RW).
Page 115: Communications
Ryan Masterfile.book Page 1 Monday, June 9, 2003 2:33 PM Communications Contents Modem ........7–2 Connecting the Modem .
Page 116: Modem
Ryan Masterfile.book Page 2 Monday, June 9, 2003 2:33 PM Communications Modem All notebook models include an RJ-11 telephone jack, and a preinstalled V.92 modem. A modem cable with RJ-11 connectors at each end is also included with select models. If you purchased a notebook with an internal modem in a country where RJ-11 telephone jacks are not standard, a country-specific modem adapter is included with the notebook.
Page 117: Connecting The Modem
Ryan Masterfile.book Page 3 Monday, June 9, 2003 2:33 PM Communications Connecting the Modem A modem must be connected to an analog telephone line. Å WARNING: To reduce the risk of electric shock, fire, or damage to the equipment, do not plug a telephone cable into the RJ-45 network jack. Å...
Page 118: Connecting A Network Cable
Ryan Masterfile.book Page 4 Monday, June 9, 2003 2:33 PM Communications Connecting a Network Cable For information on connecting a network cable, refer to the Modem and Networking Guide included on the Documentation Library CD. Turning a Network Connection Off and On To conserve power, turn off a network connection you are not using.
Page 119: Wireless (Select Models Only)
Ryan Masterfile.book Page 5 Monday, June 9, 2003 2:33 PM Communications Wireless (Select Models Only) If your notebook is equipped with a wireless device, you can connect by radio to an 802.11b or 802.11g wireless local area network (WLAN) and access computers and other resources on the network.
Page 120: To Turn Wireless Communication On And Off
Ryan Masterfile.book Page 6 Monday, June 9, 2003 2:33 PM Communications To Turn Wireless Communication On and Off Wireless networks and cellular modems are examples of devices that use wireless communication. Such devices may be restricted in some situations or environments, such as when traveling in an airplane.
Page 121: Connecting To A Wireless Network
Ryan Masterfile.book Page 7 Monday, June 9, 2003 2:33 PM Communications Connecting to a Wireless Network You can connect to an access point that gives you access to a local area network, or you can connect directly to other computers in an “ad hoc”...
Page 122: Infrared
Ryan Masterfile.book Page 8 Monday, June 9, 2003 2:33 PM Communications Infrared The notebook is IrDA-compliant and can communicate with another infrared-equipped device that is also IrDA-compliant. The IrDA connection speed standard is 4 megabits per second (Mbps). The infrared port supports low-speed connections up to 115 kilobits per second (Kbps) as well as high-speed connections up to 4 Mbps.
Page 123: Setting Up An Infrared Transmission
Ryan Masterfile.book Page 9 Monday, June 9, 2003 2:33 PM Communications Setting Up an Infrared Transmission For information about using infrared software and enabling or disabling infrared ports, refer to the operating system Help files and to the documentation included with the external infrared device.
Page 124 Ryan Masterfile.book Page 10 Monday, June 9, 2003 2:33 PM Communications 7–10 Startup and Reference Guide—Part 2...
Page 125 Ryan Masterfile.book Page 1 Monday, June 9, 2003 2:33 PM Hardware Options and Upgrades Contents External Devices ....... 8–2 Connecting a Monitor or Projector .
Page 126: Hardware Options And Upgrades
Ryan Masterfile.book Page 2 Monday, June 9, 2003 2:33 PM Hardware Options and Upgrades External Devices The jacks and connectors described in this guide support standard external devices. For information about which jack or connector to use, refer to the documentation included with the device. For information about installing or loading any software, such as drivers, required by the device, refer to the documentation included with the device.
Page 127: Connecting A Usb Device
USB (universal serial bus) is a hardware interface that can be used to connect external devices such as a USB keyboard, mouse, drive, printer, scanner, or hub to the notebook or optional HP Notebook Expansion Base. A hub is a connecting device that can be either powered or unpowered.
Page 128: Using A Usb Device
Ryan Masterfile.book Page 4 Monday, June 9, 2003 2:33 PM Hardware Options and Upgrades Using a USB Device To use a USB device, plug the device into one of the four USB connectors on your notebook. Legacy USB 1.1 support is enabled by default. This supports a USB keyboard or hub connected to a USB connector on the notebook during startup (before Windows loads) or in a non-Windows application or utility.
Page 129: Selecting A Pc Card
Ryan Masterfile.book Page 5 Monday, June 9, 2003 2:33 PM Hardware Options and Upgrades Selecting a PC Card A Type I, Type II, or Type III PC Card can be used. Zoomed video PC cards are not supported. Configuring a PC Card Ä...
Page 130: Inserting A Pc Card
Ryan Masterfile.book Page 6 Monday, June 9, 2003 2:33 PM Hardware Options and Upgrades Inserting a PC Card Ä CAUTION: To prevent damage to the PC Card connectors: Use minimal force when inserting a PC Card into a PC Card slot. Do not move or transport the notebook while a PC Card is inserted.
Page 131: Stopping And Removing A Pc Card
Ryan Masterfile.book Page 7 Monday, June 9, 2003 2:33 PM Hardware Options and Upgrades Stopping and Removing a PC Card Ä CAUTION: To prevent loss of work or an unresponsive system, stop the PC Card before removing it. ✎ Stopping a PC Card, even if it is not in use, conserves power. 1.
Page 132: Using Digital Media
Ryan Masterfile.book Page 8 Monday, June 9, 2003 2:33 PM Hardware Options and Upgrades Using Digital Media The digital media slot supports the following digital media formats: Secure Digital (SD) Multimedia Card (MMC) Memory Stick (MS) SmartMedia (SM) Ä CAUTION: To prevent damage to the digital media card connectors: Use minimal force when inserting a SD, MMC, Memory Stick, or Smart Media into a Digital Media slot.
Page 133: Using The Digital Media Light
Ryan Masterfile.book Page 9 Monday, June 9, 2003 2:33 PM Hardware Options and Upgrades Using the Digital Media Light The digital media light turns on when an inserted Digital Media card is being accessed. The digital media light turns off when inserted digital media is inactive or when the digital media slot is empty.
Page 134: Inserting Digital Media
Ryan Masterfile.book Page 10 Monday, June 9, 2003 2:33 PM Hardware Options and Upgrades Inserting Digital Media To insert a digital media card: 1. Hold the card label-side up with the connectors facing the notebook. 2. Gently push the card into the Digital Media slot until the card is seated.
Page 135: Removing Digital Media
Ryan Masterfile.book Page 11 Monday, June 9, 2003 2:33 PM Hardware Options and Upgrades Removing Digital Media To remove a Digital Media card: 1. Complete all activities that are supported by the card (such as a data transfer) and close all applications. 2.
Page 136: Increasing Memory
Hardware Options and Upgrades Increasing Memory You can increase the amount of RAM (random access memory) in the notebook with an optional HP-approved memory module. The notebook memory slot supports one 128-MB, 256-MB, 512-MB, or 1024-MB memory module. Some notebook models ship with a vacant memory slot. On other models the memory slot contains a preinstalled memory module that can be replaced at any time.
Page 137: Removing Or Inserting A Memory Module
All other areas that require a tool to access should be opened only by an HP authorized service provider. Å WARNING: To prevent exposure to electrical shock and damage to the notebook, shut down the notebook, unplug the power cord, and remove the battery pack before installing a memory module.
Page 138 Ryan Masterfile.book Page 14 Monday, June 9, 2003 2:33 PM Hardware Options and Upgrades 5. Turn the notebook upside down. 6. Remove the two memory compartment screws 1. 7. Slide the memory compartment cover towards the notebook display hinges and lift up to remove 2. Opening the memory compartment 8–14 Startup and Reference Guide—Part 2...
Page 139 Ryan Masterfile.book Page 15 Monday, June 9, 2003 2:33 PM Hardware Options and Upgrades 8. Remove or insert the memory module. To remove a memory module: a. Pull away the retention clips on each side of the module 1. (The module tilts upward.) b.
Page 140 Ryan Masterfile.book Page 16 Monday, June 9, 2003 2:33 PM Hardware Options and Upgrades To insert a memory module: a. Align the keyed (notched) edge of the module with the keyed area in the memory slot 1. b. With the module at a 45-degree angle from the surface of the memory compartment, press the module into the memory slot until it is seated 2.
Page 141 Ryan Masterfile.book Page 17 Monday, June 9, 2003 2:33 PM Hardware Options and Upgrades 9. Align the tabs on the memory compartment cover with the cover slots on the notebook, then lower the cover and slide it towards the front of the notebook 1. 10.
Page 142: Connecting An Optional Cable Lock
Ryan Masterfile.book Page 18 Monday, June 9, 2003 2:33 PM Hardware Options and Upgrades Connecting an Optional Cable Lock The purpose of security solutions is to act a deterrent. The solutions do not prevent the product from being mishandled or stolen.
Page 143: Software Updates
Ryan Masterfile.book Page 1 Monday, June 9, 2003 2:33 PM Software Updates, Restorations and Utilities Contents Updating Software ......9–2 Preparing for a Software Update .
Page 144: Software Updates, Restorations And
Prepare for a ROM (read-only memory) update by identifying the ROM version currently installed on the notebook. 1. Access the updates at the HP Web site. 2. Download and install the updates. ✎ The notebook ROM stores the BIOS (basic input-output system).
Page 145: Accessing Notebook Rom Information
Ryan Masterfile.book Page 3 Monday, June 9, 2003 2:33 PM Software Updates, Restorations and Utilities The product name, notebook model, and notebook serial number are also displayed in the same section of the Setup utility that displays ROM information, as described in the next section. Accessing Notebook ROM Information To determine whether an available ROM update is a later ROM version than the ROM version currently installed on the...
Page 146: Downloading And Installing An Update
Downloading a ROM Update: 1. Access the page at the HP Web site that provides software for your notebook: Select Start > Help and Support, then select a software update link. Or, visit the HP Web site at: http://www.hp.com/support...
Page 147 Ryan Masterfile.book Page 5 Monday, June 9, 2003 2:33 PM Software Updates, Restorations and Utilities 3. At the download area: a. Record the date, name, or other identifier of any ROM update that is later than the ROM currently installed on your notebook.
Page 148 Downloading and Installing a Non-ROM SoftPaq To update software other than a ROM update: 1. Access the page at the HP Web site that provides software for your notebook: Select Start > Help and Support, then select a software update link. Or, visit the HP Web site at: http://www.hp.com/support...
Page 149: Backing Up And Restoring Data
Setting System Restore points manually provides additional protection for your system files and settings. HP recommends that you set System Restore points: Before you add or extensively modify software or hardware.
Page 150: Repairing Or Reinstalling The Operating System
After the operating system has been reinstalled, all device drivers must also be reinstalled. HP recommends that you try to restore your system by using the System Restore utility before you consider repairing or reinstalling your operating system. For restoration instructions, refer to “Backing Up and Restoring Data”...
Page 151: Reinstalling The Operating System
Ryan Masterfile.book Page 9 Monday, June 9, 2003 2:33 PM Software Updates, Restorations and Utilities 6. Press to continue. A Licensing Agreement screen is enter displayed. 7. Press to accept the agreement and continue. The Setup window is displayed. 8. Press to repair the selected Windows installation.
Page 152: Reinstalling Device Drivers And Other Software
Ryan Masterfile.book Page 10 Monday, June 9, 2003 2:33 PM Software Updates, Restorations and Utilities 6. Press to continue. A Licensing Agreement screen is enter displayed. 7. Press to accept the agreement and continue. The Setup window is displayed. 8. Press to continue installing a new copy of the operating system instead of repairing it.
Page 153: Installing A Retail Version Of An Operating System
Ä CAUTION: Replacing an operating system enhanced by HP with a retail version of an operating system will result in the loss of all HP enhancements. In some cases, the loss of these enhancements may result in an unresponsive system or the loss of complete USB support.
Page 154: Navigating And Selecting In The Setup Utility
Ryan Masterfile.book Page 12 Monday, June 9, 2003 2:33 PM Software Updates, Restorations and Utilities Navigating and Selecting in the Setup Utility Because the Setup utility is not Windows-based, it does not support the TouchPad. Navigation and selection are by keystroke. To navigate, use the up and down arrow keys or tab.
Page 155: Specifications
Ryan Masterfile.book Page 1 Monday, June 9, 2003 2:33 PM Specifications The information in this appendix may be helpful if you plan to use or transport the notebook internationally or in extreme environments. Notebook Dimensions Dimension Metric U.S. Height (front) 4.25 cm 1.67 inches Height (rear)
Page 156: Operating Environment
DC power source, HP strongly recommends that the notebook be powered only with an AC adapter supplied or approved by HP. An AC adapter provided by HP for use with this notebook is capable of accepting AC power within the following specifications.
Page 157 Ryan Masterfile.book Page 3 Monday, June 9, 2003 2:33 PM Specifications The notebook is capable of accepting DC power within the following specifications. Input Power Rating Operating voltage 18.5V DC @6.5A- 120W Operating current 4.9A This product is designed for IT power systems in Norway with phase-to-phase voltage not exceeding 240 Vrms.
Page 158 Ryan Masterfile.book Page 4 Monday, June 9, 2003 2:33 PM Specifications A–4 Startup and Reference Guide—Part 2...
Page 159 Ryan Masterfile.book Page 1 Monday, June 9, 2003 2:33 PM Index 1394 connector 2–11 backup, system 9–7 battery bay AC adapter identifying 2–14 connecting 1–5 inserting battery pack 1–3 identifying 2–18 removing battery pack 4–26 power connector 2–11 battery light 2–8 AC power 1–12 battery pack adapter...
Page 160 Ryan Masterfile.book Page 2 Monday, June 9, 2003 2:33 PM Index button(s) Certificate of Authenticity label PC Card eject 2–13 8–6 2–16 9–9 power 2–5 compartment, memory 2–14 8–12 TouchPad 2–3 3–3 connector(s) volume 2–7 6–3 1394 2–11 See also key; latch; switch, drive 5–3 display external monitor 2–9...
Page 161 Ryan Masterfile.book Page 3 Monday, June 9, 2003 2:33 PM Index display switch function, changing 4–13 Easy CD and DVD Creator identifying 4–8 creating CDs 6–13 display, internal erasing media 6–17 brightness 3–8 features 6–14 opening 1–4 formatting media 6–16 switching image 3–7 preparing to use 6–15 Documentation Library CD 2–19...
Page 162 Ryan Masterfile.book Page 4 Monday, June 9, 2003 2:33 PM Index fn key changing function of fn+f5 changing Standby function 4–13 4–13 procedures 3–6 identifying 2–4 Quick Reference 3–5 Standby function 4–8 hotkeys commands function keys 2–4 access Help and Support 3–6 display brightness 3–8 initiate QuickLock 3–8 hard drive bay...
Page 163 Ryan Masterfile.book Page 5 Monday, June 9, 2003 2:33 PM Index IDE drive 5–4 power/standby 2–8 line-out jack 2–11 6–6 applications 2–4 lock, security cable 8–18 fn 2–4 locked system 1–10 2–5 4–10 function (F1, F2, etc.) 2–4 locking latches, battery pack 4–27 hotkeys 3–4 keypad 2–4 3–10...
Page 164 Ryan Masterfile.book Page 6 Monday, June 9, 2003 2:33 PM Index Microsoft logo key 2–4 model, identifying notebook 9–2 opening the notebook 1–4 2–2 modem operating environment approvals label 2–16 specifications A–2 cable 2–17 operating system connecting 7–3 installing retail version of 9–11 country-specific adapter 2–18 loading 4–9 specifications 7–2...
Page 165 Ryan Masterfile.book Page 7 Monday, June 9, 2003 2:33 PM Index power power/standby light 4–8 button 2–5 Preboot eXecution Environment connecting the notebook to (PXE) 7–4 external 1–5 preloaded utilities 1–9 conservation 4–4 4–25 Product Key number 2–16 controls 4–8 projector cord 2–17 connecting 2–9...
Page 166 Ryan Masterfile.book Page 8 Monday, June 9, 2003 2:33 PM Index resolution, screen 1–10 SD Card 8–8 restoring software 2–19 security cable 2–9 RJ-11 telephone jack socket services, PC Card 8–5 identifying 2–9 SoftPaq modem cable 2–17 described 9–4 RJ-45 network jack downloading and installing 9–6 identifying 2–9 software...
Page 167 Ryan Masterfile.book Page 9 Monday, June 9, 2003 2:33 PM Index specifications temperature dimensions A–1 specifications A–2 modem 7–2 storage, battery pack 4–24 network 7–3 1394 connector 2–11 operating environment A–2 time, settting the 1–10 rated input power A–2 TouchPad Standby components 3–3 avoiding when playing media...
Page 168 Ryan Masterfile.book Page 10 Monday, June 9, 2003 2:33 PM Index Windows applications key 2–4 audio-out jack Windows Media Player function 6–6 accessing with Digital Audio connecting 6–8 button 6–10 vents, fan 2–10 2–12 2–15 using with audio CDs video CDs, DVDs. See CD(s); WinDVD DVD(s) error message 6–11...
Page 169 U.S. and/or other countries. SD Logo is a trademark. The information contained herein is subject to change without notice. The only warranties for HP products and services are set forth in the express warranty statements accompanying such products and services. Nothing herein should be construed as constituting an additional warranty.
Page 170 Ryan Masterfile.book Page 12 Monday, June 9, 2003 2:33 PM...
Page 171 Ryan Masterfile.book Page 13 Monday, June 9, 2003 2:33 PM...
Page 172 Ryan Masterfile.book Page 14 Monday, June 9, 2003 2:33 PM...

HP Pavilion ZD7000 Startup And Reference Manual

Table of Contents

2 System Components

3 Keyboard

4 Power

5 Drives

6 Multimedia

7 Communications

8 Hardware Options and Upgrades

9 Software Updates, Restorations and Utilities

Quick Links

Chapters

Related Manuals for HP Pavilion ZD7000

Summary of Contents for HP Pavilion ZD7000

This manual is also suitable for:

Table of Contents