Page 2
DPL2930 DPL930VD It is important to read this instruction book prior to using your new product for the first time. Avant d’utiliser votre appareil pour la première fois, il est primordial que vous lisiez attentivement ce Guide d’Instructions. Bevor Sie Ihr neues Produkt das erste Mal anwenden, müssen Sie unbedingt dieses Bedienhandbuch lesen.
Page 3
Macrovision ALERTING YOU OF S I D E . R E F E R S E RV I C I N G I M P O R T A N T " D A N G E R O U S...
1 X grey/grey stripped wire for rear right speaker Unpacking The Speakers • one set of speakers including 1 set of left and right front speakers, 1 centre speaker, 1 subwoofer, 1 wireless signal receiver and 1 set of left and right rear speakers.
DVD writer, the write software and the disc used. 10cm/4” DVD video - Digital video discs - 12 cm and 8 cm, single or dou- Front Rear bled sided, single or dual layer. DVDs are high-density optical discs on which high quality picture and audio are recorded by means of 5cm/2”...
Setup video output You can select either S-video or SCART as your video output (default is SCART). Try power off the unit and turn it on again if you see any picture distortion on the TV. When S-VIDEO output is selected, SCART will only provide composite video signal.
Push Speaker terminal tab down to insert wire. Speaker Polarity 2. Move the TV support rod up and down as illustrated to adjust the height of the stand. Tighten the screw When connecting the speakers, make sure the polarities (“+”...
4. It is advised that you should place the receiver as high as possible. 5. The reception will be weaker if you face the back or but- tom side of the receiver to the transmitter. 6. Try turning the receiver when the reception is weak.
Advanced Setting Magnetic shielding Angle Speakers placed less than two feet from the TV set must be Placing the left and right speakers to form a 45-degree magnetically shielded in order to prevent picture distor- angle with your favorite viewing position will duplicate the tion.
(A), or to the sides or rear of the viewing area aimed upwards. In the lat- ter case, they can go right on the floor, or preferably, a few feet off the floor such as on end tables (B).
Subwoofer = STRONG details. Restore to default settings When the receiver is on and the disc tray is opened, press SUBWOOFER for 5 seconds until the screen goes black, then the initial language selection menu will appear. All system settings will be restored to default, the parental password will also be reset.
7. PRESET + / NEXT • To go to the next preset memory location in tuner mode. • To skip to the next track in CD mode and the next chapter in 1. ON / ECO DVD mode (only during playback).
3. PR+, PR- • To select programmed stations in TUNER mode. 9. MENU • To skip to the next or previous chapter, track or image in DVD, CD, mp3 • Press to exit a menu. and JPEG mode. 15. INFO (Yellow) 4.
KHz / MHz • Audio output is in Dolby Digital mode. (For DVD only) • Tuner frequency unit. • Audio output is in Dolby PL II Movie, Dolby PL II Music • Speaker Icons. or Dolby Prologic Emulation mode. • Sleep mode is activated.
Example 1: If you connect a MD player to the AUX 1 input on the receiver and press SOURCE until “AUX 1” shows on the display. You will be able to have the signal from the MD player.
3. Other sources (Tapes,etc) can be connected to this unit - AUX 2 AUX 2 IN provided that the connections are compatible. 4. Refer to the "Connecting To Audio-Visual Components" When a source is selected, the source name is shown on the section for details on connection. display.
Dolby Dolby Pro Logic II Surround. The Pro Logic II mode uses the built-in circuit to steer the Left, Center, Right and Surround left and right channel This unit is equipped with Dolby Digital 5.1-channel so audio signals and uses all five speakers to play both stereo that you can enjoy enhanced full digital surround sound.
Dolby Stereo Choosing the audio input When in AUX 1 mode, you can choose either analog in or optical in, press AUX 1 repeatedly to toggle between them. Default Settings The receiver will keep the last selection in memory as long as it doesn’t enter standby mode.
To test the speaker setting and change the speaker level In the TEST TONE menu, a short noise will come from each speaker respectively, press UP/DOWN to configure the cur- rently playing speaker.
Page 22 Advanced Sound Control Speaker Icons It is important to note, however, that not all Dolby Digital The receiver shows the speakers’ settings on the display sources are encoded with the full complement of five chan- with the following icons: nels plus subwoofer.