Connecting to Audio-Visual Components DIGITAL CONNECTION If you have a SAT receiver DVD player or CD player with a digital output, you can make use of an optical digital cable (not supplied) or coaxial digital cable (not supplied) to S-VIDEO carry the audio portion of the signal and enjoy Dolby Digital sound quality.
AM antenna and snap into place as shown nents to the receiver. below in AM Loop Antenna. 2. Press down on the Antenna tab to open the termi- Digital In Jacks can accept Dolby Digital (AC-3), DTS or PCM signals when compatible components are connected.
2/3 inch (15 mm). Press down on the tab to open the terminal CENTER FRONT SPEAKERS SPEAKERS and insert the wire. Release tab to lock wire in the terminal. RIGHT LEFT CENTER Antenna and Speaker Wire Connection...
They carry primarily music and sound effects 2 Center In surround mode, the center speaker carries much of the dialogue as well as music and effects. It should be set between the left and right speakers. 3 Surround (Rear Speakers) Their overall sound balance should be as close as pos- sible to the front speakers.
Even though you adjust the surround channel to be Function = Tuner as loud as the others on the test signal, you'll find Volume setting = 45 that on actual program material the surround chan- Bass &...
Preset” on pg 16) Remote control selector must be on hifi. 15. Operations Buttons In Tuner mode, press REV or FWD keys to tune down 1. ON/OFF or up radio frequency. To turn on or off the receiver and other auxiliary The remote control currently operates most components (see page 14 “Using the Remote to...
Operating Your Receiver Display DVD / VCR / SAT / TUNER / TAPE / V-AUX / COAX C D / TV • Coaxial digital input detected. • The arrow points to the repective icon to show the current source. • Tuner stereo signal detected.
Operating Your Receiver Switching on/off Example 1: If you connect a VCR player to the VCR input (audio + video) on the receiver and press the SOURCE • To switch on the receiver, press ON/ECO button on the main unit until VCR1/ANL button once, or any source button on the remote shows on the display.
TAPE IN/OUT (audio only) NOTE - FM/AM built-in When a source is selected, the arrow will point to the To play Dolby Digital or DTS sound, the source source name on the display. must be connected to the receiver via the opti-...
Operating the Radio 5- Tune the stations by pressing TUNING UP or DOWN on the main unit or REV or FWD on the remote control repeatedly until the desired station is The receiver has a built-in tuner that allows for found.
Page 19
Storing radio stations: Manual preset The receiver can store up to 40 radio stations in 1. Select FM or AM band by pressing BAND on the memory. You can enter every single radio station main unit or tuner onthe remote control repeatedly.
Page 20
MEMO on the remote control to enter preset setting hifi dvd /cd mode (MEMORY icon shows on display), Press TUN- down ING UP/DOWN on the unit or pr+ / pr - on the vcr/sat rep. remote control to select preset station. TUNING...
Page 21
SUBWOOFER 6 CH. EXTERNAL INPUT PRE OUT RELIGION = any aspect of beliefs, faith & God or Gods PHONE IN = public forum by phone TRAVEL = feature and programs concerning travelling To activate 6 Channel external input, press the HOBBY = recreational activities &...
Dolby Surround. Dolby Pro Logic II The Pro Logic II mode uses the built-in circuit to steer the This unit is equipped with Dolby Digital 5.1-channel so Left, Center, Right and Surround left and right channel that you can enjoy enhanced full digital surround sound.
The selected source and input source will be displayed size and type of listening environment. Press DSP on the display as long as they are active, except for MODE on the main unit to select among DSP some temporary change of display (e.g. adjusting vol- options.(Not available in Dolby Digital/DTS)
Right Speaker Configurations 2. To adjust the volume level of the test tone, turn up/down the VOLUME knob or press vol + / - key on You can also change the setup of the speakers by the remote control. pressing the SETUP button until the display shows...
Page 25
If the letter is flashing, the signal is either too weak or just gone. 5. When set up is done, wait for 5 seconds to auto- matically save your settings or press any key to save your selection and set up mode.
Install the batteries before attempting to operate the Frequency Response: 40Hz to 20kHz +/-3dB remote. Be sure to match the + and - ends of each bat- Signal to Noise Ratio: 65dB (Dolby digital mode mode) tery to the symbols shown in the remote battery com- partment.
Satellite Receiver Standby/on Switch the key to vcr/sat position to control the THOMSON VCR or a SAT Access to the menu with the center VCR only setting functions...
Standby/on Switch the key to dvd/CD position to control the Thomson DVD or CD unit DVD only Access to the menu with the setting functions Audio...
Page 30
Universal remote control Programming You can program your remote control to control other devices. Before making the following adjustments, see below for the 3 number code which corresponds to the brand of your device, and write it down in the chart below.