THOMSON 42WB03SW - annexe 1 Manual

Plasma monitor

Advertisement

WARNINGS & PRECAUTIONS
! To prevent damage which may result in fire or shock hazard, do not expose this product to rain or
moisture.
! To prevent electric shock, do not remove cover. No user serviceable parts are inside. Refer servicing to
qualified service personnel only.
! Keep monitor away from excessive dust, high temperatures, moisture or direct sunlight.
! Use in a well-ventilated area and do not cover ventilation openings.
! Unauthorized modification of this equipment or usage of an unshielded connecting cable may cause
excessive interference.
! When the monitor is not in use for a long period of time, disconnect it from the electric outlet.
! If the picture displayed is in any way abnormal, turn off the unit and disconnect it from the electric outlet.
Check your signal wire connections and reconnect the monitor to the electric outlet.
! Switch the monitor off using the ON/OFF button, on the rear panel, and disconnect it from the electric
outlet before cleaning. Do not use liquid or aerosol cleaners. Use only a slightly damp cloth for cleaning.
! Do not place this product on an unstable cart, stand or table. The product may fall, causing serious
damage.
! Do not place the unit on a bed, sofa, rug, or other similar surfaces. Never place the unit near or over a
radiator or heat source. Do not install unit in an enclosed area unless proper ventilation is provided.
! The unit should be operated from the type of power source indicated on the label. If the type of available
power is unknown, consult your dealer or local power company.
! The unit is equipped with a 3-pin grounded plug. The plug will only fit into a grounded power outlet. This is
a safety feature. If you are unable to insert the plug into the outlet, contact your electrician. Do not alter
the plug; this will defeat the safety feature.
! Do not rest objects on the power cord and avoid placing power cord near high traffic areas.
! Do not overload wall outlets and extension cords as this can result in a risk of fire or electric shock.
! Switch the monitor off using the ON/OFF button, on the rear panel, disconnect it from the main supply and
refer servicing to qualified service personnel under the following conditions:
Power cord or plug is damaged or frayed.
Liquid has been spilled into the product.
Unit has been exposed to water or moisture.
Unit does not operate normally when the operating instructions are followed. Adjust only those controls
that are covered by the operating instructions, improper adjustment of other controls may result in
damage which often requires extensive work by a qualified technician to restore the unit to normal
operation.
Unit has been dropped or the cabinet has been damaged.
Unit exhibits a distinct change in performance, indicating a need for service.
! Use the screen saver when using a computer.
! Switch the monitor to standby mode when you do not use it.
THOMSON is not liable if the unit is not used in accordance with this manual.
42WB03SW-EN-5-062303.p65

IMPORTANT SAFETY INSTRUCTIONS

WARNING
RISK OF ELECTRIC SHOCK
DO NOT OPEN
WARNING: To reduce the risk of electric shock, do no remove the front or back covers.
No user-serviceable parts inside. Refer servicing to qualified service personnel only.
The lightning flash with arrow-head
within a triangle is intended to inform
the user that parts inside the product
are a risk of electric shock.
1
The exclamation point within a triangle
is intended to inform the user that
important operating and servicing
instructions are explained.
2003/6/23, PM 04:52
EN
1

Advertisement

Table of Contents
loading

Summary of Contents for THOMSON 42WB03SW - annexe 1

  • Page 1: Important Safety Instructions

    ! Do not place the unit on a bed, sofa, rug, or other similar surfaces. Never place the unit near or over a radiator or heat source. Do not install unit in an enclosed area unless proper ventilation is provided.
  • Page 2: Compliance With Ce Standards

    The CE label on this monitor indicates that it complies with the 89/336/EEC directive on electromagnetic compatibility and safety rules as defined in the 73/23/EEC and 93/68/EEC low voltage directives. This unit is protected against interferences from other electronic devices, provided that these devices comply with the standards in force.
  • Page 3: Table Of Contents

    Rear View ............................. 6 CONNECTING THE MONITOR ........................7 Connecting the tuner unit ........................8 Connecting a PC using the RGB IN input ..................... 9 Connecting a PC via the tuner unit ..................... 10 USING THE MONITOR ........................... 11 Powering ON / OFF ..........................11 Selecting Signal Source ........................
  • Page 4: Cleaning And Maintenance

    If the surface is particularly dirty, soak a soft, lint-free cloth in a mild detergent solution. Wring the cloth to remove excess liquid. Wipe the surface of the display to remove dirt. Then use a dry cloth of the same type to dry.
  • Page 5: Package Contents

    PACKAGE CONTENTS Supplied Accessories Please check that the monitor package contains the following items: Power cord Plasma Monitor User Manual Optional Accessories The following accessories are available and may be purchased from your local sales representative: Wall Mount (ACC 913) Audio Cinch Cable 42WB03SW-EN-5-062303.p65...
  • Page 6: Understanding Your Monitor

    If the main power switch (rear of panel) is turned off, this LED will not illuminate. Volume Adjustment +/- Buttons ! ! ! ! ! Yellow - Standby (Power OFF) with AC power Use these buttons to adjust volume up and down. detected They can also be used for adjustment in menus.
  • Page 7: Connecting The Monitor

    You can view TV images from the tuner unit, using the DVI socket, and you can connect to this tuner different units such as a satellite receiver, a videorecorder, a DVD player, etc. You can also connect a computer via the RGB sockets.
  • Page 8: Connecting The Tuner Unit

    CONNECTING THE MONITOR Connecting the tuner unit The following diagram shows how to connect the tuner unit. Plasma Monitor Main Power Tuner Unit 42WB03SW-EN-5-062303.p65 2003/6/23, PM 04:52...
  • Page 9: Connecting A Pc Using The Rgb In Input

    You can connect a PC to your Wysius , directly using a VGA cable (not provided). Connect the cable to the RGB IN socket, on the plasma monitor, and to the corresponding socket, on the computer. Plasma Monitor Main Power Computer 42WB03SW-EN-5-062303.p65...
  • Page 10: Connecting A Pc Via The Tuner Unit

    Connecting a PC via the tuner unit You can connect a PC via the tuner unit. To do so, connect one end of a VGA cable (not provided) to the PC IN socket, on the front panel of the tuner unit, and the other end to the corresponding socket on the computer.
  • Page 11: Using The Monitor

    ! ! ! ! ! Green - Power ON Selecting Signal Source 1. Press the INPUT button on the front panel to select one of the available input signal soruces. Input Select (Toggle) This button is only active in RGB mode (when you connect a PC, directly or through the tuner unit).
  • Page 12: Advanced Functions

    1. Press the MENU +/- buttons on the front panel to access the main menu. 2. Use the ADJ +/- buttons to access the “OTHER” sub-menu as displayed below. Please note that the front panel buttons are only active in RGB mode (when you connect a PC, directly or through the tuner unit).
  • Page 13: Sound Adjustments

    2. Use the ADJ +/- buttons to access the “SOUND” sub-menu. 3. Use the MENU +/- buttons to select the various options described in this section. Please note that the front panel buttons are only active in RGB mode (when you connect a PC, directly or through the tuner unit).
  • Page 14: Signal Frequency Information Display

    1. Press the MENU +/- buttons on the front panel to access the main menu. 2. Use the ADJ +/- buttons to access the “OTHER” sub-menu. Please note that the front panel buttons are only active in RGB mode (when you connect a PC, directly or through the tuner unit).
  • Page 15: Adjusting Picture

    An explanation of each adjustment is listed below. 4. Use the ADJ +/- buttons to change the setting. Please note that the front panel buttons are only active in RGB mode (when you connect a PC, directly or through the tuner unit). Contrast Adjust Contrast to increase the level of “white”...
  • Page 16: Troubleshooting

    TROUBLESHOOTING Troubleshoot Common Conditions The following table lists some problems that you may encounter and methods for remedy. Please refer to this table before contacting a service representative. Possible Cause Remedy Symptom No picture is displayed. The power cord is disconnected.
  • Page 17: Specifications

    Pixel Pitch 1.08mm X 1.08mm Luminosity 1000 cd/m (without filter) Power Source Input voltage 100 ~ 240 Vac , 50 / 60 Hz Input current 3.3A Inrush current 60 A p-p/20ms Max. Power consumption 380±10% Watts Stand-by & Power Save 5 Watts Max.
  • Page 18 17 TMDS Data 0- TMDS Data 2+ 10 TMDS Data 1+ 18 TMDS Data 0+ TMDS Data 2/4 Shield 11 TMDS Data 1/3 Shield 19 TMDS Data 0/5 Shield TMDS Data 4- 12 TMDS Data 3- 20 TMDS Data 5-...
  • Page 19 No pulse No pulse No video Power off Power saving Pulse No pulse blanked Less than 5 watts No pulse Pulse This Plasma display is Energy star compliant when used with a computer equipped with DPMS. 42WB03SW-EN-5-062303.p65 2003/6/23, PM 04:52...
  • Page 20 SPECIFICATIONS Preset Timing Chart Item Description: Total time Active display area including borders Active display area excluding borders Left/Top border Right/bottom border Blanking time Front porch Sync-width Back porch Mode No H Resolution V Resolution Refresh Rate Pixel 25.175 31.5 31.5...
  • Page 21 H Resolution 1024 1024 1024 1024 1280 1280 1280 V Resolution 1024 1024 1024 Refresh Rate Pixel 78.75 94.5 157.5 28.320 25.175 MHz Horizontal visible 1024 1024 1024 1024 1280 1280 1280 Dots Horizontal total 1344 1328 1312 1376 1688...
  • Page 22: Wall Mount Installation (Optional)

    WALL MOUNT INSTALLATION (OPTIONAL) Package Content An optional wall-mount is available. Please contact your local retailer for more information. Left Wall Angle Right Wall Angle Horizontal Support Module Module Screws for Wall Screws for Fix Angle x 8 Mounting x 8 42WB03SW-EN-5-062303.p65...
  • Page 23 WALL MOUNT INSTALLATION (OPTIONAL) Setup Steps Step 1. Attach Horizontal Supports (C and D) to the Left and Right Wall Angle Module ( A and B) with screws (E). Step 2. Install the Wall Mount Bracket onto the wall. Note: The screws in this package are for mounting onto a wooden wall.
  • Page 24 This type of equipment is to be installed by qualified installers, please contact with authouized dealer for installation. Please make sure that your wall is capable of supporting this wall mount and plasma monitor which can weigh over 120 kg.

This manual is also suitable for:

42wb03sw 1

Table of Contents