TP-Link Tapo RV10, Tapo RV10 Lite - Robot Vacuum & Mop Manual
Package Contents
Overview
Power/Clean
- Press once: Start/pause cleaning.
- Press and hold for 5 seconds: Turn on/off the robot vacuum. *For the first use, slide the power switch from OFF to ON to turn on.
Dock
- Return to the dock to charge.
Spot Cleaning/Child Lock
- Press once: Start spot cleaning.
- Press and hold for 5 seconds: Turn on/off the child lock.
Combination Button
- Press and hold simultaneously for 5 seconds:
Enter setup mode to configure network. - Press and hold simultaneously for 10 seconds:
Restore to factory default settings.
LED
- Red: Battery level < 20%; Error
- Orange: Battery level between 20% and 80%
- Green: Battery level > 80%
Position the Dock
- Remove the bottom cover of the dock, connect the power cord to the dock, and then replace the cover.
- Place the dock on a level surface, flat against a wall, without obstacles within 1.5m (4.9ft) in front and 0.5m (1.6ft) on left and right.
Notes - To ensure a better user experience, make sure the area is with good Wi-Fi signals.
- Do not place it in direct sunlight. Ensure the area around the dock is free of clutter to improve docking performance.
- To prevent the risk of your robot vacuum falling downstairs, ensure that the dock is placed at least 1.2m (4 ft) away from stairs.
- Always keep the dock powered on, otherwise the robot vacuum will not automatically return. And do not move the dock frequently.
- Place a waterproof pad to prevent the mop from wetting the floor when the robot vacuum is being charged.
Remove Protective Strip
Before use, remove the protective strips on both sides of the front bumper.
Remove Protective Film
Remove the protective film on the front bumper.
Power On and Charge
Slide the power switch from OFF to ON to turn on your robot vacuum.
Notes
- If the power switch is in the ON position, you can also press and hold the button for 5 seconds to turn on/off your robot vacuum.
- If the power switch is in the OFF position, the robot vacuum will automatically turn on when it is charged on the dock, and turn off when it leaves the charging dock.
Place the robot vacuum on the charging dock or tap to send it back to the dock to charge.
It will return to the dock at the end of a cleaning job and whenever it needs to recharge.
Notes
- When the LED of the charging dock flashes 3 times and then goes out, the charging will begin.
- We recommend that you charge the robot vacuum fully for about 4 hours prior to starting the first cleaning job.
Download the Tapo App and Connect to Wi-Fi
- Download the Tapo app from the App Store or Google Play, then log in.
OR
- Open the Tapo app, tap + icon, and select your model. Follow the step-by-step instructions to easily set up your robot vacuum.
In the Tapo app, you can enjoy the following functions.
- Cleaning Modes & Preferences
Customize vacuum power, water level, and cleaning times. - Scheduled Cleaning
Set an automatic cleaning schedule, then the robot vacuum will clean automatically at the set time and return to the dock after cleaning.
Cleaning
Press Once
Start/pause cleaning.
Press Once
Start spot cleaning.
Notes
- Cleaning cannot start if the battery is too low. Charge your robot vacuum first.
- Pick up obstacles like wires, clothing, and plastic bags. Loose wires and objects may get caught in the robot vacuum, resulting in disconnection or damage to wires and property.
- Put away high pile carpet before cleaning.
- Do not pick up the robot vacuum during cleaning.
- If the cleaning area is too small, the area may be cleaned twice.
- If the robot vacuum is idle for 10 minutes, it will automatically enter sleep mode and the cleaning job will be canceled.
The robot vacuum will automatically explore and clean your home in neat rows. It will return to the charging station at the end of a cleaning job and whenever it needs to recharge.
In Spot Cleaning mode, it will sweep the circular area with a diameter of 1.5m (4.9ft) calculated from its own position.
Mopping
- Take out the dustbin and water tank.
- Remove the rubber plug and add up to 300ml of water to the water tank.
- Fill with cool/room temperature water only. Be careful not to wet the metal contacts.
- Use only cleaning agents specified by Tapo. Others may corrode the water tank.
- Install the washable mop cloth.
- Install the mop cloth mount.
- Re-install the dustbin and water tank.
- Vacuum floors at least 3 times before the first mopping cycle.
- The ability to cross obstacles is reduced when mopping.
- It is recommended to wash the mop cloth after each use.
- Remove the mop cloth mount.
- Empty the water tank.
- Remove the washable mop cloth.
- Clean the mop cloth.
- Sun dry mop cloth and mop cloth mount.
Care and Maintenance
To maintain optimal performance, maintain the robot vacuum according to the following guidelines.
Part | Maintenance Frequency | Replacement Frequency* |
Dustbin | Clean/wash as needed | / |
Filter | Once a week | 3-6 months |
Main Brush | Every 2 weeks | 6-12 months |
Side Brush | Once a month | 3-6 months |
Mop Cloth | After each use | 2-3 months |
Caster Wheel | Clean as needed | / |
Main Wheels | Once a month | / |
Sensors | Once a month | / |
Charging Contacts | Once a month | / |
*Replacement frequency may vary depending on the actual situation. Parts should be replaced if visible wear appears.
Empty the Bin
- Remove the dustbin and water tank.
- Open the dustbin to empty the dustbin.
- Place the dustbin back inside the robot vacuum.
Clean the Filter
- Remove the dustbin and open the lid.
- Remove the filter.
- Clean the filter with a cleaning brush.
- Wash the dustbin and filter.
Do not wash with hot water or detergents. - Air-dry the dustbin and filter thoroughly, then install the filter in the previous orientation.
Clean the Main Brush
- Turn the robot vacuum over, then unlatch and remove the main brush cover.
- Remove the brush and its end cap.
- Remove any hair or debris with the cleaning brush.
- Re-install the cap and main brush. Press on the main brush cover to lock it in place.
Clean the Side Brush
- Pull firmly to remove the side brush and remove any entangled debris. Wipe with a damp cloth if needed.
- Re-install the side brush and press it tightly to ensure it is installed in place.
Clean the Caster Wheel
- Pull firmly to remove the caster wheel and remove hair or dirt.
- Re-install the caster wheel and press it firmly in place.
Clean Main Wheels
Wipe main wheels with a clean, dry cloth.
Clean the Sensors
Wipe the sensors with a clean, dry cloth.
Wipe the charging contacts with a clean, dry cloth.
Troubleshooting
Issues | Solution |
Setup failure | - Check if the power switch on the left side of the robot vacuum is toggled to "ON".
- The battery level is low. Please place the robot vacuum on the dock to charge and it will start automatically when it is ready.
- Check your internet connection or check if you have configured Allow List or Firewall settings on your router.
|
Charging failure | - Please remove the robot vacuum and check whether the indicator light of the dock is on, and make sure that both ends of the power adapter of the dock are plugged in.
- Poor contact. Please clean up the spring contacts on the dock and the charging contacts on the robot vacuum.
|
Recharge failure | - There are many obstacles near the dock. Please place the dock in an open area and try again.
- The robot vacuum is far from the dock. Please place the robot vacuum near the dock and try again.
- Please clean up the spring contacts on the dock and the recharge sensor/charging contacts on the robot vacuum.
|
Abnormal operation | Shut down and try again. |
Abnormal noise during cleaning | There may be foreign matter entangled in the main brush, side brush or wheels. Please clean up after shutdown. |
Decreased cleaning ability or dust leakage | - The dustbin is full. Please clean the dustbin.
- The filter is clogged. Please clean or replace the filter.
- The main brush is entangled by foreign matter. Please clean the main brush.
|
Failure to connect to Wi-Fi | - The Wi-Fi signal is poor. Please make sure the robot vacuum is in an area with good Wi-Fi signals.
- Wi-Fi connection is abnormal. Please reset the Wi-Fi and download the latest app and try again.
- The password is entered incorrectly. Please check.
- The robot vacuum only supports the 2.4 GHz frequency band. Please connect to a 2.4 GHz Wi-Fi.
|
Scheduled cleaning doesn't work | - The battery level is low. The scheduled cleaning will work when the battery level is above 20%.
- The cleaning is already in progress when the schedule starts.
- Do Not Disturb is set in the app. Make sure the schedule is not within the set Do Not Disturb period.
- There is no internet access for your Wi-Fi network and your robot vacuum has restarted.
|
Whether the robot vacuum consumes power when it is placed on the dock | The power consumption is very low when the robot vacuum is placed on the dock, which helps the battery to maintain optimal performance. |
Whether the robot vacuum needs to be charged for 16 hours for the first three times | Lithium battery has no memory effect when in use, and there is no need to wait when it is fully charged. |
If the corresponding issues cannot be solved by referring to the above methods, please contact our Technical Support.
Energy Saving Mode
When the robot vacuum is docked, press and hold the Power button and the Dock button for about 15 seconds until you hear an alert sound. It will also enter the Energy Saving mode when it is fully charged.
In this mode, only the charging feature will work. Other functions will not work, such as LEDs will be off, sensors will not work, and Wi-Fi will be disconnected.
To exit the Energy Saving mode, press any button on the robot vacuum.
Customize Cleaning Preferences
Swipe up the panel to set cleaning times and vacuum power as needed.
- Choose cleaning times from 1 to 3.
- Choose vacuum power from Quiet, Standard, Turbo, and Max. The noise might be loud with the max vacuum power.
- Choose water level from None, Low, Moderate, and High.
Low: Suitable for wooden floors.
Moderate: Suitable for wood and tile floors.
High: Suitable for kitchen and dining floors.
Schedule Your Robot Vacuum to Clean Regularly
Add cleaning schedules to have your robot vacuum clean floors regularly.
- Tap the menu icon on the top right corner. Tap "Schedules".
- Tap the + icon or "Add Schedule".
- Set the time when your robot vacuum starts cleaning.
- Customize the cleaning preferences including cleaning time, vacuum power, and water level as needed.
- If you want to receive a notification before the cleaning job starts, you can set the alert time. And you will be notified before each cleaning job starts, and you can also disable a scheduled cleaning.
- Choose days you want to repeat the cleaning.
- Tap "Save" on the top right corner to apply settings.
Documents / Resources
References
Download manual
Here you can download full pdf version of manual, it may contain additional safety instructions, warranty information, FCC rules, etc.
Download TP-Link Tapo RV10, Tapo RV10 Lite - Robot Vacuum & Mop Manual
Need Assistance?
Do you have a question about the Tapo RV10 that isn't answered in the manual? Leave your question here.