Ricoh AficioSP C410DN Quick Installation Manual

Quick Installation Guide
Read this manual carefully before you use the product and keep it handy for future reference.
For safe and correct use, please be sure to read the Safety Information in "Safety Information"
before using the machine.
❖ Optimum Environmental Conditions
Where to Put the Printer
Permissible and recommended temperature and
humidity ranges are as follows:
The printer's location should be carefully chosen
because environmental conditions greatly affect its
performance.
Warning
• Confirm that the wall outlet is near the machine and
freely accessible, so that in event of an emergency, it
can be unplugged easily.
• Only connect the machine to the power source
described on this manual.
• Avoid multi-wiring.
• Do not damage, break or make any modifications to
%RH
the power cord. Do not place heavy objects on it, pull
it hard or bend it more than necessary. These actions
could cause an electric shock or fire.
• The supplied power cord is for use with this equipment
only. Do not use with other appliances. Doing so may
result in fire, electric shock, or injury.
Caution
• Do not handle the plug with wet hands. Doing so might
cause an electrical shock.
• White area: Permissible Range
• Keep the machine in an area that is within optimum
• Gray area: Recommended Range
environmental conditions. Operating the machine in
an environment that is outside the recommended
ranges of humidity and temperature can cause an
electrical fire hazard. Keep the area around the socket • The machine must be level within 5 mm, 0.2˝ from
free of dust. Accumulated dust can become an
both front to rear and left to right.
electrical fire hazard. • To avoid possible build-up of ozone, locate this
machine in a large well ventilated room that has an
• Place the machine on a strong and level surface.
air turnover of more than 30 m
Otherwise, it might fall and injure someone.
• When you use this machine for a long time in a
• If you use the machine in a confined space, ensure
confined space without good ventilation, you may
there is continuous air circulation.
detect an odd smell. To keep the workplace
comfortable, we recommend you keep it well
ventilated.
❖ Space Required for Installation
Leave enough space around the printer. This space is
❖ Space Required for Installation
necessary to operate the printer. The recommended (or
minimum) space requirements are as follows:
• Areas exposed to direct sunlight or strong light
• Dusty areas
• Areas with corrosive gases
• Areas that are excessively cold, hot, or humid
• Locations near air conditioners or humidifiers
• Locations near other electronic equipment
• Locations subject to frequent strong vibration
❖ Power Source
Connect the power cable to a power source of the
AQC025S
following specification:
A: 50 cm (19.7 inches) or more
B: 10 cm (4 inches) or more
• 120 V, 60 Hz, 11 A or more
C: 10 cm (4 inches) or more
D: 70 cm (27.6 inches) or more
Checking the Contents of
the Box
Follow the procedure below to verify the items that
come with the printer.
• Ensure that the box contains all items listed below. If
there are any missing or defective items, contact your
sales representative.
❖ Manuals and CD-ROMs
Quick Installation Guide (This manual)
CD-ROM "Printer Drivers and Utilities"
CD-ROM "Manuals"
CD-ROM "Document Management Utility"
Ferrite Core x 2
Toner Cartridges: Black (K), Magenta (M), Cyan
TS4K031KE
(C), Yellow (Y)
3 /hr/person.
Paper Feed Unit Labels
Color Calibration Sample Sheet
Additional Documentation
• This package does not include an interface cable.
Purchase one to use with your host computer. See
"Appendix", Hardware Guide.
Unpacking
To protect it from shock and vibration during transit,
this printer comes packaged in cushioning foam and
secured with tape. Remove these protective materials
after bringing the machine to where it will be installed.
Caution
• When lifting the machine, use the inset grips on both
sides. The printer could break or cause an injury if
dropped.
• Place no objects on the left or inner cover.
• Be sure to remove all four strips of tape from the
photo conductor unit to avoid malfunction.
• Removed tape is dirty. Be careful not to let it touch
your hands or clothes.
Remove the plastic bag.
AET510S
Lift the printer with two people by using
the inset grips on both sides of the printer.
AET028S
AET034S
• Leave the tape holding the paper feed tray and cover
in place while moving the printer.
• Lower the machine slowly and carefully to prevent
trapping your hands.
AET031S
Remove the orange adhesive tape from
the printer body.
Open the left cover. Do not remove the
orange tape attached to the left cover.
AQC026S
CLP30DN/CLP27DN/C7531dn/C7526dn/LP231cn/
LP226cn/Aficio SP C411DN/Aficio SP C410DN
Turn the two green levers Remove the protective sheet, as shown.
counterclockwise ( ), and then slowly
Pinch the orange tape, and then pull it
open the inner cover ( ).
out.
AQC032S
Remove the end of the tape from the pinter.
Turn the green lever clockwise to lock
the unit.
AET802S
Remove the four pieces of tape from
the photo conductor unit.
Close the inner cover. Lock the inner
cover by pressing in ( ) and then
turning the two green levers clockwise
( ).
AET803S
Remove the securing pin, as shown,
from the transfer unit. Pinch it, and
then pull it out.
Close the left cover.
Close the left cover firmly using both hands, until it
clicks into place.
Open the top cover by grasping the
handles on the left and right sides.
AET804S
Turn the green lever of the transfer unit
counterclockwise to unlock the unit.
AET805S
AET806S
AET146S
AQC014S
AQC007S