Ricoh Aficio CL5000 Quick Installation Manual

QUICK INSTALLATION GUIDE
Please read the Safety Information in Maintenance Guide 1 before using this machine. It
contains important information related to USER SAFETY and PREVENTING EQUIP-
MENT PROBLEMS.
WHERE TO PUT THE PRINTER
Power Connection
Connect the power cord to a power source with the following
The printer's location should be carefully chosen
specifications:
because environmental conditions greatly affect its
❒ 120 V, 60 Hz, 11 A or more-
performance.
Space Required for Installing the Printer
Warning
• Confirm that the wall outlet is near the machine Leave enough space around the printer. This space is necessary to
operate the printer. The recommended (or minimum) space
and freely accessible, so that in event of an
requirement is as follows:
emergency, it can be unplugged easily.
• Only connect the machine to the power source
described on this manual.
• Avoid multi-wiring.
• Do not damage, break or make any modifications
to the power cord. Do not place heavy objects
A
on it, pull it hard or bend it more than necessary.
These actions could cause an electric shock or
fire.
Caution
• Keep the machine away from humidity and dust.
A fire or an electric shock might occur.
• Place the machine on a strong and level surface.
A: 10 cm (4 inch) or more
Otherwise, the machine might fall and result in
B: 10 cm (4 inch) or more
an injury.
• If you use the machine in a confined space, C: 55 cm (22 inch) or more
D: 75 cm (30 inch) or more
confirm that there is a continuous flow of air.
Optimum Environmental Conditions
Recommended temperature and humidity
%RH
10˚C 80% 27˚C 80%
80
15˚C 70% 25˚C 70%
32˚C
54%
60
UNPACKING THE PRINTER AND
CHECKING THE CONTENTS OF THE BOX
40
15˚C 30% 25˚C 30%
Caution
15 10˚C 15% 32˚C 15%
• To prevent an injury, this printer should be lifted
˚C
10 20 30
by at least two people.
%RH
50˚F 80% 80.6˚F 80%
Check the contents of the box according to the
80
59˚F 70% 77˚F 70%
following list. If one or some items are missing,
89.6˚F
please contact your sales or service
54%
60
representative.
Important
40
❒ This package does not include an interface cable.
59˚F 30% 77˚F 30%
Please purchase one for use with your host
15 50˚F 15% 89.6˚F 15%
computer. See "Appendix" the in the Administrator
Reference.
50 60 70 80 90 ˚F
MANUALS FOR THIS PRINTER
Possible operation range Recommended range
Quick Installation Guide (This manual)
The machine must be level within 5 mm (0.2 inch) both front to
Maintenance Guide 1
rear and left to right.
Maintenance Guide 2
To avoid possible build-up of ozone, place this printer in a large well
ventilated room that has an air turnover of more than 30 m 3 (183
Option Setup Guide
cubic inch)/hr/person.
CD-ROM "Printer Drivers and Utilities"
If you use this printer in a cold area, leave the printer on or severe
CD-ROM "Operating Instructions"
cold might damage sensitive components inside the printer.
CD-ROM "Document Management Utility"
Depending on the temperature and humidity around the machine,
Development Unit Test Print
vapor might occur when printing. Thus steam can be seen when
prints come out. Power Cable
Ferrite Core
Environments to Avoid
Fuser Oil Unit
Important
❒ Locations exposed to direct sunlight or strong light
❒ Dusty areas
❒ Areas with corrosive gases
❒ Areas excessively cold, hot, or humid
❒ Locations near an air conditioner or humidifier
Paper Feed Unit Labels
❒ Locations near other electronic equipment
❒ Locations where the printer might be subjected to
frequent strong vibration
<G071-7503B>
Remove the plastic bag.
Lift the printer and move it to the place where
you want to install it.
When lifting the printer, pull out the holding handles from the sides
of the printer, and hold them with at least two people.
B
C
Important
❒ When installing the printer to a low position, be
careful not to get your hand or clothes caught under
D
the printer.
Return the grips into the printer.
ZESX302E
Remove adhesive tapes and packing materials
from the printer.
Put the Paper Feed Unit label for Tray 1 on the
front of Tray 1.
PREPARING THE
DEVELOPMENT UNIT
Warning
• Do not incinerate spilled toner or used toner.
Toner dust is flammable and might ignite when
exposed to an open flame.
• Disposal should take place at an authorized
dealer or an appropriate collection site.
• If you dispose of the used toner containers
yourself, dispose of them according to the local
regulations.
Caution
• Do not eat or swallow toner.
• Keep toner (used or unused) and toner
cartridges out of reach of children.
• Our products are engineered to meet the highest
standards of quality and functionality. When
purchasing expendable supplies, we
recommend using only those provided by an
authorized dealer.
ZESX303J
Open the left cover of the printer by pulling the
fasteners ( c ).
ZESX306E
Note
❒ The two round fasteners cannot be detached.
From the top, the development units are installed in the order of
black, yellow, cyan, and magenta.
ZESX307E
Remove all of the packing materials with red tags.
Four packing materials are connected together, and there are two
of them. Remove one by one from the top of the units by holding
the packing material, not the wire.
ZESX433E
ZESX308E
Detach the connectors from the development
units from the top to the bottom by pressing the
sides of the connectors.
ZESX410J
Set the development unit by aligning the guides,
Follow steps to for each development unit
pushing towards direction (
individually. Remove the development unit by
inserting slowly until it stops ( ).
lifting it first as shown in the illustration (
c
).
The illustration shows how to install the black development unit.
The procedure is the same for all four colors.
ZESX411E
The illustration shows how to remove the black development unit.
Note
The procedure is the same for all four colors.
❒ When installing the development unit, it may come
out a little. This is not a malfunction.
Important
❒ Be sure to hold the unit with both hands, and then Confirm the label for the color, and then confirm
pull it slowly. that the unit is securely fit in the stoppers.
Hold the development unit, and then shake it
about 10 times.
When there is a white line showing at the stoppers, reinsert the units.
Important
ZESXE414J
❒ If the development unit is not installed properly,
Important
the printing quality may be poor.
❒ Hold the unit with the roller facing down.
Repeat steps
❒ Do not add shocks to the unit.
development units.
❒ If you do not shake the unit well, it may take longer
for the machine to warm up when turned on.
Insert the connectors to the development units
❒ Do not touch the roller or the gears shown in the
from the bottom ( ) to the top ( ) until they
illustration.
click into place.
ZESX668E
Important
❒ Be sure that all four connectors are connected to
the development units. Turning on the power
without all four connectors connected to the units
may cause a printer malfunction.
Close the left cover of the printer by pushing the
fasteners ( ) while holding the cover ( ).
), and then
ZESX412E
ZESX650J
to to set the rest of the
ZESX046E
ZESX309E