Related Manuals for THOMSON THT504
Summary of Contents for THOMSON THT504
- Page 1 Digital Terrestrial HD Receiver THT504 User Manual Manuel d’utilisation Manuale utente Manual del usuario Manual do Utilizador Instrukcja obsługi Felhasználói kézikönyv Ръководство на потребителя...
- Page 4 This product has been manufactured and sold under the responsibility of STRONG Group. THOMSON and the THOMSON logo are trademarks of Technicolor (S.A.) or its affiliates and are used under license by STRONG Group. Represented by STRONG Ges.m.b.H. Franz-Josefs-Kai 1 1010 Vienna, Austria Email: support_at@thomsonstb.net...
-
Page 5: Table Of Contents
STRONG declares that this item complies with the basic requirements and other relevant regulations of directives 2004/108/EC and 73/23/EC, RoHS 2002/95/EC. THOMSON and the THOMSON logo are trademarks of Technicolor (S.A.) or its affiliates and are used under license by STRONG Group. Any other product, service, company, trade name and logo referenced herein are neither endorsed nor sponsored by Technicolor (S.A.) or its affiliates. -
Page 6: Introduction
1.0 INTRODUCTION 1.1 Safety Instructions DO NOT INSTALL YOUR RECEIVER: In a closed or poorly ventilated cabinet; directly on top of or under any other equipment; on a surface which might obstruct the ventilation slots. DO NOT EXPOSE THE RECEIVER OR ITS ACCESSORIES: - To direct sunlight or any other equipment that generates heat;... -
Page 7: Equipment Set-Up
the receiver in its original packaging with its accessories. Failing to comply with such packaging procedures could damage the product and void your warranty. 1.3 Equipment Set-up We recommend you consult a professional installer to set up your equipment. Otherwise, please follow the instructions below: - Refer to the user manual of your TV and antenna. -
Page 8: Your Receiver
2.0 YOUR RECEIVER 2.1 DEFAULT PIN: 1234 2.2 Front Panel Fig. 1 IR sensor Point your remote control towards this sensor. Mode indicator RED indicates that the receiver is in STANDBY mode. GREEN indicates that the receiver is in OPERATING mode. Connector for USB storage devices. -
Page 9: Installing The Batteries
EXIT Exits from the menu or sub-menu Menu Off: Change channel to previous/next. Menu On: Moves the cursor up/down. 10. tu Menu Off: Increases/decreases the volume level. Menu On: Change settings for specific menus 11. OK Menu Off: Displays the current channel list Menu On: Activates the highlighted menu item. -
Page 10: Connection
NOTE: Managing the receiver will be limited or not possible if there are obstacles between the remote control sensor (at the front panel of the receiver) and the remote control. Direct sunlight or very bright light can reduce or disturb the reception of the remote control signals. -
Page 11: Connecting To A Digital Audio Amplifier And Tv Using Hdmi
3.5 Connecting to a digital audio amplifier and TV using HDMI Fig. 6 By connecting your receiver to the latest digital amplifiers or Home Cinema systems you will enjoy the best possible sound quality and multi-channel audio (depending on broadcast). Connect the HDMI output of the receiver to an input of your amplifier, and then connect the HDMI output of the amplifier to your TV set. -
Page 12: Quick Guide To Using Your Receiver
Select All to store scrambled and free to air channels or select Free Scan mode: to store only free to air channels. Note: Scrambled channels cannot be viewed with this receiver. Use this option to adjust the established connection to your TV set. Connection: Select HDMI or TV SCART. -
Page 13: Operation
6.0 OPERATION Your new receiver is equipped with several features to make watching TV a true pleasure. This paragraph describes these features. Please also read chapter 7.0 to get familiar with the menu of your receiver. 6.1 Changing channels Following ways are possible for changing channels with your new receiver: Via direct access using the 0~9 buttons. -
Page 14: Teletext
Use pq to select the desired stream and confirm with OK. The audio channel as stereo, mono, left and right can be selected with the tu buttons. 6.4 Teletext Your receiver includes a fully featured Teletext. To access Teletext, press the TTX button in viewing mode and use the 0~9 buttons to input the number of the page you wish to see. -
Page 15: Instant Recording
6.8 Instant Recording Your new receiver allows you to make an instant recording of the programme you are watching. Simply press RECORD to start the recording. To enter the duration for the recording, press RECORD again. Use the 0~9 buttons to enter the recording time and press OK to confirm. At the beginning of the recording a recording sign will be shown for a short while on the upper left corner of your TV screen. - Page 16 To lock or unlock a channel, press RED while in TV Channel List. Press pq to select a channel and press OK to lock or unlock it. You are asked to input the PIN code. (DEFAULT PIN: 1234) Locked channels will be marked with the symbol. Locking/unlocking multiple channels in one session is possible.
-
Page 17: Installation
enter them with OK. When you have finished editing, press BLUE to enter the changes. When all changes have been made, press EXIT twice. Select Yes to save the changes or No to discard. Delete Press BLUE in Edit Channel to enable the Delete function. The Delete sign will move up to indicate that Delete is selected. -
Page 18: System Setup
7.2.2 Channel Scan Use pq to select Installation, press OK or u to advance. Use pq to select Channel Scan and press OK to enter. Use tu to toggle between available scan modes: By Channel and By Frequency. If By Channel is selected, use the cursor buttons to select Scan Band and Channel No. If By Frequency is selected, use the cursor buttons to select Frequency and Bandwidth. - Page 19 7.3.2 TV System Use this menu to match your receiver to your TV set. The following settings are available: Use this option to select the video resolution of your TV screen. Video Resolution: Options are: By Source (automatic detection of video resolution offered to the receiver), By Native TV (automatic detection of maximal resolution of TV screen), and manual selections 480i, 576i up to 1080p Please use a setting that matches your TV’s...
- Page 20 7.3.4 Timer Setting This menu allows you to set up to 8 timed events for recording or waking up the receiver. Use pq to select Timer Setting from the System Setup menu and press OK to enter. The receiver will display a list with 8 timers, followed by their respective status. Select the timer you wish to set or change with pq and press OK to proceed.
-
Page 21: Tools
7.3.7 Auto Standby Auto Standby is a new feature that helps you reducing power consumption. When set to 30Min/1 Hour/2 Hours or 3 Hours, the receiver will switch to standby if it doesn’t receive any commands during this time. Set Auto Standby to Off to deactivate the automatic standby function. -
Page 22: Games
Select Upgrade by USB from the Tools menu and press OK to proceed. The upgrade menu will now be displayed. Use pq to select Upgrade Mode and choose option Allcode. Use pq to select Upgrade File and choose the file containing the latest and correct software. Once all settings are made, move the highlight to Start and press OK to start the upgrade process. - Page 23 First select which files you like to play back. Use the button 1 to switch between Video/Record/ Music or Image. Press pq to select a file or folder and then press OK to open the folder/ subfolder (if applicable) or start playback of the file. Press the EXIT button to exit. Use the buttons like described below in order to choose functions during the different playback modes (like described in the help banner below): Video:...
- Page 24 EXIT: One step back or leave the folder and quit the function. Image: Press 4 to open a previously created play list. Then you can select the image file that you want to add your play list by pressing 5 (a single file will be added to the play list) or 6 (all files of this directory/folder will be added to the play list).
-
Page 25: Troubleshooting
Use pq to move the highlight and tu to change settings. Select between Auto, Pause or Off. When Timeshift is set to Auto Timeshift: it will automatically start every time after tuning to a channel. When Timeshift is set to Pause it will start only after pressing the YELLOW/2 button. -
Page 26: Technical Specifications
Problem Possible cause What to do No picture or sound on TV HDMI or SCART is not Switch to correct TV/amplifier or amplifier selected on your TV or input amplifier or the unit is set to Select lower resolution on higher resolution as the TV receiver supports. - Page 27 Video Decoder Profile level: MPEG-2 MP@ML, AVC/H264HP@L4.1, MPEG4 ASP supported Video resolutions: 480i / 480p / 576i / 576p / 720p / 1080i / 1080p / By Native TV /By source Decoding & Video out: Aspect ratio: 4:3 Letterbox, 4:3 Pan & Scan, 16:9, Auto Audio Decoder Audio support: Dolby Digital Plus*/AC3+/PCM...
- Page 28 Operating temperature: 0 °C ~ +40 °C Storage temperature: -10 °C ~ +50 °C Operating humidity range: 10~85%, RH, Non-condensing Size (WxDxH) in mm: 148 x 130 x 37 Net-weight: 0.26kg...