Elkay EZSG8WS 1B Series Installation & Use Manual
Bottle filling stations & coolers
Hide thumbs
Also See for EZSG8WS 1B Series:
- Installation & use manual (10 pages) ,
- Installation, care & use manual (10 pages)
Advertisement
Quick Links
EZSG8WS*1B
LZSG8WS*1B
INSTALLATION & USE MANUAL
Manual de instalación y uso
Manuel d'installation et d'utilisation
EZ™ & LZ ™ Series Bottle Filling Stations & Coolers
EZ™ & LZ™ Serie versatil Botella Bombas y Enfriadores
EZ™ & LZ™ Stations de Remplissage de Bouteille Série et Refroidisseurs
Page 1
1000001713 (Rev. G - 04/18)
Advertisement
Related Manuals for Elkay EZSG8WS 1B Series
Summary of Contents for Elkay EZSG8WS 1B Series
- Page 1 EZSG8WS*1B LZSG8WS*1B INSTALLATION & USE MANUAL Manual de instalación y uso Manuel d’installation et d’utilisation EZ™ & LZ ™ Series Bottle Filling Stations & Coolers EZ™ & LZ™ Serie versatil Botella Bombas y Enfriadores EZ™ & LZ™ Stations de Remplissage de Bouteille Série et Refroidisseurs Page 1 1000001713 (Rev.
- Page 2 EZSG8WS*1B LZSG8WS*1B Note: Danger! Electric shock hazard. Disconnect power before servicing unit. Nota: peligro! Peligro de descarga eléctrica. Desconecte antes de reparar la unidad. Remarque : Danger ! Risque d'électrocution. Débrancher avant de réparer l'appareil. Pictured is unit only without bottle filler. En la foto, la unidad sólo sin relleno botella.
- Page 3 EZSG8WS*1B LZSG8WS*1B Fig. 2 Page 3 1000001713 (Rev. G - 04/18)
-
Page 4: Entretien
EZSG8WS*1B LZSG8WS*1B HANGER BRACKETS & TRAP INSTALACIÓN DE LOS SOPORTES INSTALLATION DES SUPPORTS INSTALLATION FIJADORES Y EL PURGADOR DE SUSPENSION ET DU SIPHON 1) Remove hanger bracket fastened to back of Retire el soporte fijador que se encuentra conectado 1) Retirez le support de suspension fixé au dos du cooler by removing one (1) screw. - Page 5 EZSG8WS*1B LZSG8WS*1B Service Instructions Lower and Upper Shroud To access the refrigeration system and plumbing connections, remove four screws from bottom of cooler to remove the lower shroud. To remove the upper shroud for access to the pushbars, regulator, solenoid valve or other components located in the top of the unit, remove lower shroud, disconnect drain, remove four screws from tabs along lower edge of upper shroud, unplug two wires and water tube.
-
Page 6: Top Cover
EZSG8WS*1B LZSG8WS*1B 7/16” BOLT HOLES FOR MOUNTING FASTENING UNIT TO WALL TOP COVER SCREWS UNIT CENTER LINE Fig. 4 Fig. 5 BRACKET & SCREWS Fig. 7 Fig. 6 Bottle Filler Installation Instructions 1) Remove two (2) mounting screws with 5/32” Allen wrench holding top cover to Bottle Filler (See Fig. 5). Remove top cover. Note do not discard mounting screws, they will be needed to reinstall top cover. - Page 7 EZSG8WS*1B LZSG8WS*1B BF11 - BF12 PROGRAM SETTING THE CONTROL BOARD VERIFY CONTROL BOARD SOFTWARE Continued from below: 1) To verify the software program of the control board the unit will 2) When the display changes to “SETTINGS”, depress the button again. need to be shut down and restarted.
- Page 8 EZSG8WS*1B LZSG8WS*1B NOTE: When installing replacement bubbler and pedestal, tighten nut only to hold parts snug in position. Do Not Overtighten. NOTA: Al instalar el grifo y pedestal de reemplazo, apriete la tuerca unicamente para mantener las piezas en una Basin posicion adjustada.
- Page 9 EZSG8WS*1B LZSG8WS*1B OPERATION OF QUICK CONNECT FITTINGS OPERATION OF QUICK CONNECT FITTINGS SIMPLY PUSH IN SIMPLY PUSH IN TUBE IS SECURED TUBE IS SECURED PUSH IN COLLET PUSH IN COLLET TUBE TO ATTACH IN POSITION TO RELEASE TUBE TUBE TO ATTACH IN POSITION TO RELEASE TUBE PUSHING TUBE IN BEFORE...
- Page 10 INFORMATIONS POUR LE SERVICE PAR NUMERO SANS FRAIS 1.800.260.6640 PRINTED IN U.S.A. IMPRESO EN LOS E.E.U.U. IMPRIMÉ AUX É.-U. ELKAY MANUFACTURING COMPANY • 2222 CAMDEN COURT • OAK BROOK, IL 60523 • 630.574.8484 1000001713 (Rev. G - 04/18) Page 10...