Related Manuals for Record KEANE MONROE 2000 Series
Summary of Contents for Record KEANE MONROE 2000 Series
-
Page 1: Hand Of Door Identifiction
SERIES 2000 KEANE MONROE a member of the record group INSTALLATION INSTRUCTIONS MONROE, NC, USA 28111 800 438 1937 REGULAR ARM PARALLEL ARM PARALLEL ARM / PANIC BREAKAWAY SLIDE ARM... -
Page 2: Table Of Contents
KEANE MONROE SERIES 2000 PAGE 1 INSTALLATION INSTRUCTIONS a member of the record group INDEX and OPERATOR HANDING MONROE, NC, USA 28111 800 438 1937 The KM Series 2000 operator has been carefully designed, built, and tested to provide years of service. - Page 3 KEANE MONROE SERIES 2000 PAGE 2. INSTALLATION INSTRUCTIONS a member of the record group ELECTRICAL PREPARATION MONROE, NC, USA 28111 800 438 1937 OWNER INFORMATION TO BE PROVIDED BY THE DISTRIBUTOR / INSTALLER • After the installation instruct the owner on the safe operation of the door.
-
Page 4: Back Plate Installation
KEANE MONROE SERIES 2000 PAGE 3. INSTALLATION INSTRUCTIONS a member of the record group ELECTRICAL PREPARATION (cont.) MONROE, NC, USA 28111 800 438 1937 ELECTRICAL POWER CONCEALED SURFACE MOUNT Run flexible conduit or 3-wire cable down Connect 90 degree elbow to bracket as side jamb, through cut-out. - Page 5 KEANE MONROE SERIES 2000 PAGE 4. INSTALLATION INSTRUCTIONS a member of the record group BACK PLATE INSTALLATION MONROE, NC, USA 28111 800 438 1937 HOLE PREPARATION INSTRUCTIONS For Metal frames with 1/8” or greater material thickness, drill #7 hole and tap for 1/4-20 x 3/4” machine screws as required.
- Page 6 KEANE MONROE SERIES 2000 PAGE 5. a member of the record group INSTALLATION INSTRUCTIONS DUAL BACK PLATE INSTALLATION MONROE, NC, USA 28111 800 438 1937 Installation of Covers and Back plates of a different length than Door Opening 1. Mounted as is...
-
Page 7: Operator Installation - Regular Arm
KEANE MONROE SERIES 2000 PAGE 6. INSTALLATION INSTRUCTIONS a member of the record group OPERATOR INSTALLATION - REGULAR ARM MONROE, NC, USA 28111 800 438 1937 Mounting Operator Right Hand Shown, Left Hand Opposite Mount operator to backplate using 1/4-28 fillister head screws with lockwashers as shown. -
Page 8: Operator Installation Parallel & Slide Arm
KEANE MONROE SERIES 2000 PAGE 7. INSTALLATION INSTRUCTIONS a member of the record group OPERATOR INSTALLATION PARALLEL & SLIDE ARM MONROE, NC, USA 28111 800 438 1937 Mounting Operator Right Hand Shown, Left Hand Opposite Mount operator to backplate using 1/4-28 fillister head screws with lockwashers as shown. -
Page 9: Regular Arm Installation
KEANE MONROE SERIES 2000 PAGE 8. INSTALLATION INSTRUCTIONS a member of the record group REGULAR ARM INSTALLATION MONROE, NC, USA 28111 800 438 1937 Regular Arm Installation Door must have Door Stop Centerline of Hinge Pin Door Preparation for Regular Arm 14 1/4”... - Page 10 KEANE MONROE SERIES 2000 PAGE 9. INSTALLATION INSTRUCTIONS a member of the record group REGULAR ARM INSTALLATION (CONT’D.) MONROE, NC, USA 28111 800 438 1937 Rod End Rod End Sleeve Main Arm Shoe Secondary Rod 1/4-20x5/8” Rd.Hd. Mach. Screw Main Arm Or #14x1 1/4”...
-
Page 11: Parallel Arm Installation
KEANE MONROE SERIES 2000 PAGE 10. INSTALLATION INSTRUCTIONS a member of the record group PARALLEL ARM INSTALLATION MONROE, NC, USA 28111 800 438 1937 Parallel Arm Installation Caution: Before proceeding with preparation of door, determine the depth of reveal. See Table below. - Page 12 KEANE MONROE SERIES 2000 PAGE 11. a member of the record group INSTALLATION INSTRUCTIONS PARALLEL ARM INSTALLATION (CONT.) MONROE, NC, USA 28111 800 438 1937 Sleeve Stud Screw Rod End Rod End Main Arm Door Bracket Secondary Rod Indexing Mounting Parallel Arm Pinion Shaft 1.
-
Page 13: Manual Rotation Of Operator Pinion
KEANE MONROE SERIES 2000 PAGE 12. INSTALLATION INSTRUCTIONS a member of the record group MANUAL ROTATION OF OPERATOR PINION MONROE, NC, USA 28111 800 438 1937 Manual Rotation of Operator Pinion Sweep Valve Pinion 1. Using the main arm or an open end wrench, rotate pinion of operator approximately 1/4 turn, hold in that position. -
Page 14: Parallel Arm Installation With Panic Breakaway
KEANE MONROE SERIES 2000 PAGE 13. INSTALATION INSTRUCTIONS a member of the record group PARALLEL ARM INSTALLATION W/ PANIC BREAKAWAY MONROE, NC, USA 28111 800 438 1937 Parallel Arm Installation with Panic Breakaway Caution: Before proceeding with preparation of door, determine the depth of reveal. - Page 15 KEANE MONROE SERIES 2000 PAGE 14. INSTALLATION INSTRUCTIONS a member of the record group PARALLEL ARM INST. W/PANIC BREAKAWAY(CONT.) MONROE, NC, USA 28111 800 438 1937 Panic Breakaway Main Arm Stud Screw Secondary Rod Rod End Sleeve Door Bracket Rod End...
-
Page 16: Panic Breakaway Adjustment
KEANE MONROE SERIES 2000 PAGE 15. INSTALLATION INSTRUCTIONS a member of the record group PANIC BREAKAWAY ADJUSTMENT & CHECK MONROE, NC, USA 28111 800 438 1937 Panic Breakaway Adjustment and Checkout Tension Preset The tension on the panic breakaway assy. has been pre-adjusted at the factory before shipment. -
Page 17: Slide Arm Installation
KEANE MONROE SERIES 2000 PAGE 16. a member of the record group INSTALLATION INSTRUCTIONS MONROE, NC, USA 28111 800 438 1937 SLIDE ARM INSTALLATION Slide Arm Installation Door frame must have door stop Door preparation for Slide Arm RH shown, LH opposite Door opening width Dim. - Page 18 KEANE MONROE SERIES 2000 PAGE 17. INSTALLATION INSTRUCTIONS a member of the record group SLIDE ARM INSTALLATION CONT’D MONROE, NC, USA 28111 800 438 1937 Main Arm Slide Track Assy. Pinion Shaft Drive Roller Slide arm Mounting Slide Arm 1. Insert stud into drive roller, screw stud into threaded hole...
- Page 19 KEANE MONROE SERIES 2000 PAGE 18. INSTALLATION INSTRUCTIONS a member of the record group SPEED AND PRESSURE ADJUSTMENT MONROE, NC, USA 28111 800 438 1937 Adjustment and Checkout Speed and Pressure Important Test all functions of the operator using operational switching devices such as sensors, press wall switches, or mats and the On/Off/Hold Open switch.
- Page 20 KEANE MONROE SERIES 2000 PAGE 19. INSTALLATION INSTRUCTIONS a member of the record group LIMIT SWITCH ADJUSTMENT & CHECKOUT MONROE, NC, USA 28111 800 438 1937 Limit Switch Adjustment and Checkout Function of Limit Switch The operation of the motor is to open the door, not to hold it open. The limit switch is used to shut off the motor after opening the door through the back check zone, thus allowing the door energy to be quenched before the 90°...
- Page 21 KEANE MONROE SERIES 2000 PAGE 20. a member of the record group INSTALLATION INSTRUCTIONS BACKCHECK ADJUSTMENT AND CHECKOUT MONROE, NC, USA 28111 800 438 1937 Backcheck Adjustment and Checkout Backcheck The KM operator has a dual backcheck system, 1) a backcheck valve (“BC”) which regulates the cushioning of the door to the...
- Page 22 KEANE MONROE SERIES 2000 PAGE 21. INSTALLATION INSTRUCTIONS a member of the record group SWEEP AND LATCH ADJUSTMENT AND CHECK MONROE, NC, USA 28111 800 438 1937 Adjustment and Checkout Sweep and Latch 0 sec. Door Closing Control Sweep The closing speed of the door is controlled by the sweep...
-
Page 23: Cover Installation
KEANE MONROE SERIES 2000 PAGE 22. INSTALLATION INSTRUCTIONS a member of the record group COVER INSTALLATION MONROE, NC, USA 28111 800 438 1937 Cover Installation Important Before installing the cover, be sure that all wires are secured in such a manner they will not interfere with the operation of the unit or the installation of the cover. - Page 24 KEANE MONROE SERIES 2000 PAGE 23. INSTALLATION INSTRUCTIONS a member of the record group SIGNAGE and CODE CONFORMANCE MONROE, NC, USA 28111 800 438 1937 Signage Application Make sure all doors have proper signage as follows. An arrow sign (Fig. 1) shall be visible from the approach side of a swinging door mounted on the door at a height 58 inches ±...
- Page 25 KEANE MONROE SERIES 2000 PAGE 24. a member of the record group “D” CONTROL WIRING DIAGRAM MONROE, NC, USA 28111 800 438 1937...
- Page 26 KEANE MONROE SERIES 2000 PAGE 25. a member of the record group “B” CONTROL WIRING DIAGRAM MONROE, NC, USA 28112 800 438 1937...
- Page 27 KEANE MONROE SERIES 2000 PAGE 26. a member of the record group OPERATOR WIRING DIAGRAM MONROE, NC, USA 28112 800 438 1937...